SIGMA TEK SR 022 Bedienungsanleitung

SR 022

S-DIAS Current Controller Module

Instruction Manual

Date of creation: 06.06.2017

Version date: 26.07.2023

Article number: 20-029-022-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

tributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not responsi-

ble for technical or printing errors in the handbook and assumes no responsibility for damages that occur through

use of this handbook.

S-DIAS CURRENT CONTROLLER MODULE SR 022

26.07.2023 Page 1

S-DIAS Current Controller Module SR 022

with1 DC motor driver

1 incremental encoder input

1 digital input +5 V

2 digital inputs +24 V

The S-DIAS SR 022 current controller module is used to operate a DC

motor with a 12-30 V supply voltage and a maximum motor current of

3.5 A. Higher starting currents are possible for a short period.

Additionally, the motor contains an incremental encoder input (optional

TTL or RS422 signal), as well as three digital inputs (1x +5 V, 2x +24 V).

SR 022 S-DIAS CURRENT CONTROLLER MODULE 
 
Page 2 26.07.2023 
Contents 
Introduction............................................................................. 4 
1 Target Group/Purpose of this Operating Manual......................4 
2 Important Reference Documentation .........................................4 
3 Contents of Delivery.....................................................................4 
2Basic Safety Directives .......................................................... 5 
1 Symbols Used...............................................................................5 
2 Disclaimer......................................................................................7 
3 General Safety Directives ............................................................8 
4 Software/Training .........................................................................9 
3Standards and Directives......................................................10 
1 Directives.....................................................................................10 
1.1 EU Conformity Declaration................................................................10 
4Type Plate...............................................................................11 
5Technical Data .......................................................................12 
1 Motor Output Specifications......................................................12 
2 Incremental Encoder Input Specifications...............................13 
3 +5 V Digital Input Specifications...............................................14 
4 +24 V Digital Input Specifications.............................................14 
5 Electrical Requirements.............................................................14 
6 Miscellaneous .............................................................................17 
7 Environmental Conditions.........................................................17 

 S-DIAS CURRENT CONTROLLER MODULE SR 022 
 
07.2023 Page 3 
6Mechanical Dimensions........................................................18 
7Connector Layout..................................................................19 
1 Status LEDs.................................................................................20 
2 Applicable Connectors...............................................................21 
3 Label Field...................................................................................22 
8Wiring.....................................................................................23 
1 Wiring Example...........................................................................23 
2 Note..............................................................................................24 
9Assembly/Installation ...........................................................25 
1 Check Contents of Delivery.......................................................25 
2 Mounting......................................................................................26 
Addressing.............................................................................28 
Transport/Storage .................................................................31 
Storage...................................................................................31 
Maintenance...........................................................................32 
1 Service.........................................................................................32 
2 Repair...........................................................................................32 
Disposal .................................................................................32 
Hardware Class SR022 .........................................................33 

SR 022 S-DIAS CURRENT CONTROLLER MODULE

Page 4 26.07.2023

15.1 General.........................................................................................34

15.2 DC Motor......................................................................................35

15.3 Incremental Encoder..................................................................36

15.4 Communication Interfaces.........................................................37

1. Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x SR 022

S-DIAS CURRENT CONTROLLER MODULE SR 022

26.07.2023 Page 5

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the speci-

fied measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the speci-

fied measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the speci-

fied measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

SR 022 S-DIAS CURRENT CONTROLLER MODULE

Page 6 26.07.2023

WARNING

Hot Surfaces

Surfaces chaudes

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require atten-

tion.

S-DIAS CURRENT CONTROLLER MODULE SR 022

26.07.2023 Page 7

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the sub-

sequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine opera-

tor is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If neces-

sary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product descrip-

tion. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this operat-

ing manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

SR 022 S-DIAS CURRENT CONTROLLER MODULE

Page 8 26.07.2023

2.3 General Safety Directives

The Safety Directives in the other sections of this operating manual must be observed.

These instructions are visually emphasized by symbols.

INFORMATION

According to EU Directives, the operating manual is a component of a

product.

This operating manual must therefore be accessible in the vicinity of

the machine since it contains important instructions.

This operating manual should be included in the sale, rental or transfer

of the product, or its online availability indicated.

Regarding the requirements for Safety and health connected to the use

of machines, the manufacturer must perform a risk assessment in

accordance with machine directives 2006/42/EG before introducing a

machine to the market.

Operate the unit with devices and accessories approved by

SIGMATEK only.

Inhaltsverzeichnis

Andere SIGMA TEK Steuereinheit Handbücher

SIGMA TEK

SIGMA TEK CCP 531 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SAI 041 Bedienungsanleitung

SIGMA TEK

SIGMA TEK ST 011 Bedienungsanleitung

SIGMA TEK

SIGMA TEK KL 090 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 0812 Bedienungsanleitung

SIGMA TEK

SIGMA TEK ISE 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK CP 112 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 022-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 211 Bedienungsanleitung

SIGMA TEK

SIGMA TEK MDP 102-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK CP 101 Bedienungsanleitung

SIGMA TEK

SIGMA TEK PL 221 Bedienungsanleitung

SIGMA TEK

SIGMA TEK HZS 7321 Bedienungsanleitung

SIGMA TEK

SIGMA TEK STO 081 Bedienungsanleitung

SIGMA TEK

SIGMA TEK CSDI 162 Bedienungsanleitung

SIGMA TEK

SIGMA TEK KL 180 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DC 061-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK PIM 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK PW 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS DM 821 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DC 061-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111-2 Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS AI 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AM 441 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung