SIGMA TEK CP 101 Bedienungsanleitung

CP 101

S-DIAS CPU Module

Instruction Manual

Date of creation: 10.04.2014

Version date: 26.07.2023

Article number: 20-004-101-E

Publisher: SIGMATEK GmbH & Co KG

A-5112 Lamprechtshausen

Tel.: +43/6274/4321

Fax: +43/6274/4321-18

Email: [email protected]

WWW.SIGMATEK-AUTOMATION.COM

SIGMATEK GmbH & Co KG

Translation of the Original Instructions

distributed in any form (print, photocopy, microfilm or in any other process) without the express permission.

We reserve the right to make changes in the content without notice. The SIGMATEK GmbH & Co KG is not

responsible for technical or printing errors in the handbook and assumes no responsibility for damages that occur

through use of this handbook.

S-DIAS CPU MODULE CP 101

26.07.2023 Page 1

S-DIAS CPU Module CP 101

with 1 Ethernet

1 USB Device

1 CAN

The S-DIAS CP 101 CPU module is a high-performance processor unit

for the S-DIAS I/O modules. With the Ethernet and CAN bus interfaces,

the module can be used for various applications. A zero-voltage

protected RAM area is available, which is implemented by copying a

data block from the DDR RAM to the NAND Flash.

The voltage supply is already available in the module. The number of

modules that can be supplied depends on the total current consumption

The CP 101 can supply a maximum of 0.6 A.

S-DIAS has no intelligent master (manager).

CP 101 S-DIAS CPU MODULE 
 
Page 2 26.07.2023 
Contents 
1Introduction............................................................................. 5 
1.1 Target Group/Purpose of this Operating Manual......................5 
1.2 Important Reference Documentation .........................................5 
1.3 Contents of Delivery.....................................................................5 
2Basic Safety Directives .......................................................... 6 
2.1 Symbols Used...............................................................................6 
2.2 Disclaimer......................................................................................8 
2.3 General Safety Directives ............................................................9 
2.4 Software/Training .......................................................................10 
3Standards and Directives......................................................11 
3.1 Directives.....................................................................................11 
3.1.1 EU Conformity Declaration................................................................11 
4Type Plate...............................................................................12 
5Technical Data .......................................................................13 
5.1 Performance Data.......................................................................13 
5.2 Standard Configuration..............................................................14 
5.3 Electrical Requirements.............................................................14 
5.3.1 Module Supply (Input) .......................................................................14 
5.3.2 S-DIAS Bus Supply (Output) .............................................................15 
5.4 Miscellaneous .............................................................................17 
5.5 Environmental Conditions.........................................................17 

 S-DIAS CPU MODULE CP 101 
 
07.2023 Page 3 
6Mechanical Dimensions........................................................18 
7Connector Layout..................................................................19 
1 Status LEDs.................................................................................20 
2 Connectors..................................................................................20 
3 Applicable Connector Cables....................................................21 
4 Applicable Connectors...............................................................22 
5 Label Field...................................................................................23 
8CAN Bus Setup......................................................................24 
1 CAN Bus Station Number ..........................................................24 
2 Number of CAN Bus Participants..............................................24 
3 CAN Bus Data Transfer Rate.....................................................24 
4 CAN Bus Termination.................................................................25 
9Strain Relief ...........................................................................26 
Process Diagram...................................................................27 
Status and Error Messages..................................................28 
Application Exceptions.........................................................35 
1 Data Breakpoint ..........................................................................35 
Wiring Guidelines..................................................................35 
1 Shielding......................................................................................36 
2 ESD-Protection............................................................................36 

CP 101 S-DIAS CPU MODULE 
 
Page 4 26.07.2023 
Assembly/Installation............................................................37 
1 Check Contents of Delivery.......................................................37 
2 Mounting......................................................................................38 
Transport/Storage..................................................................40 
Storage ...................................................................................40 
Maintenance...........................................................................41 
1 Service.........................................................................................41 
2 Repair...........................................................................................41 
Disposal..................................................................................41 
 

S-DIAS CPU MODULE CP 101

26.07.2023 Page 5

1 Introduction

1.1 Target Group/Purpose of this Operating Manual

This operating manual contains all information required for the operation of the product.

This operating manual is intended for:

•Project planners

•Technicians

•Commissioning engineers

•Machine operators

•Maintenance/test technicians

General knowledge of automation technology is required.

Further help and training information, as well as the appropriate accessories can be found

on our website www.sigmatek-automation.com.

Our support team is happily available to answer your questions.

Please see our website for our hotline number and business hours.

1.2 Important Reference Documentation

This and additional documents can be downloaded from our website or obtained through

support.

1.3 Contents of Delivery

1x CP 101

CP 101 S-DIAS CPU MODULE

Page 6 26.07.2023

2 Basic Safety Directives

2.1 Symbols Used

The following symbols are used in the operator documentation for warning and danger

messages, as well as informational notes:

DANGER

Danger indicates that death or serious injury will occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Danger indique une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

WARNING

Warning indicates that death or serious injury can occur, if the

specified measures are not taken.

To avoid death or serious injuries, observe all guidelines.

Avertissement d’une situation dangereuse qui, faute de prendre les

mesures adéquates, entraînera des blessures graves, voire mortelles.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

CAUTION

Caution indicates that moderate to slight injury can occur, if the

specified measures are not taken.

To avoid moderate to slight injuries, observe all guidelines.

Attention indique une situation dangereuse qui, faute de prendre les

mesures adéquates, peut entraîner des blessures assez graves ou

légères.

Respectez toutes les consignes pour éviter des blessures

graves, voire mortelles.

S-DIAS CPU MODULE CP 101

26.07.2023 Page 7

INFORMATION

Information

Provides important information on the product, handling or

relevant sections of the documentation, which require

attention.

CP 101 S-DIAS CPU MODULE

Page 8 26.07.2023

2.2 Disclaimer

INFORMATION

The contents of this operating manual were prepared with the greatest

care. However, deviations cannot be ruled out. This operating manual

is regularly checked and required corrections are included in the

subsequent versions. The machine manufacturer is responsible for the

proper assembly, as well as device configuration. The machine

operator is responsible for safe handling, as well as proper operation.

The current operating manual can be found on our website. If

necessary, contact our support.

Subject to technical changes, which improve the performance of the

devices. The following operating manual is purely a product

description. It does not guarantee properties under the warranty.

Please thoroughly read the corresponding documents and this

operating manual before handling a product.

SIGMATEK GmbH & Co KG is not liable for damages caused

through, non-compliance with these instructions or applicable

regulations.

Inhaltsverzeichnis

Andere SIGMA TEK Steuereinheit Handbücher

SIGMA TEK

SIGMA TEK CCP 531 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111 Bedienungsanleitung

SIGMA TEK

SIGMA TEK STO 081 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 211 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111-S Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS DM 821 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AM 222 Bedienungsanleitung

SIGMA TEK

SIGMA TEK PIM 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK ST 011 Bedienungsanleitung

SIGMA TEK

SIGMA TEK C-DIAS Bedienungsanleitung

SIGMA TEK

SIGMA TEK PL 221 Bedienungsanleitung

SIGMA TEK

SIGMA TEK SCP 111-2 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AI 022-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK MDP 102-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AM 441 Bedienungsanleitung

SIGMA TEK

SIGMA TEK S-DIAS AI 022 Bedienungsanleitung

SIGMA TEK

SIGMA TEK HMI-Link G2 Device Bedienungsanleitung

SIGMA TEK

SIGMA TEK EZ 101 Bedienungsanleitung

SIGMA TEK

SIGMA TEK VI 021 Bedienungsanleitung

SIGMA TEK

SIGMA TEK AO 046 Bedienungsanleitung

SIGMA TEK

SIGMA TEK STO 081 Bedienungsanleitung

SIGMA TEK

SIGMA TEK DC 061-1 Bedienungsanleitung

SIGMA TEK

SIGMA TEK CSDI 162 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung