SIIG CyberSerial Dual PCI Bedienungsanleitung

CyberSerial PCI

Quick Installation Guide

04-0388A

Introducing the CyberSerial PCI

The CyberSerial PCI high-speed serial I/O card provides

one additional 9-pin serial port. Depending on the

model purchased, this board will fit into either a Full or

Low Profile chassis.

FeaturesandBenefits

•Conforms to PCI v2.2 Plug and Play

•Reduces CPU load and improves system

performance dramatically

•IRQ sharing feature reduces IRQ conflicts

•High-speed serial port (9-pin) works with 56K V.90

external modems, ISDN terminal adapters, PDAs,

digital cameras, label printers and other serial port

devices

•Built-in FIFO buffers dramatically increase data

transmit/receivespeed,especiallyunderWindows'

multitasking environment

•Serial port can be configured for either 5V or 12V

output, for serial devices that require power

SystemRequirements

•Pentium or equivalent computer with an available

PCI slot

•DOS, Windows 95/98/98SE/ME/NT 4.0/2000/

XP/Server 2003

•Linux Kernel 2.4.x or later

PackageContents

•CyberSerial PCI board

• DriverCD

• Low profile bracket (Dual Profile board only)

• Quick installation guide

Layout

JP1

Serial Port

(9-pin)

Full profile

bracket

Figure 1. Layout

Note: Depending on the model purchased, the

bracket size will be either Full or Low-profile.

JumperSettings(JP1)

Open = 0 volts (default)

Short 1-2 = 5V

Short 2-3 = 12V

Note: Mostserialdevicesdonotrequire additional

power through the serial port. Refer to your serial

device's manual for more information.

Hardware Installation

General instructions for installing the card are provided

below, since the design of computer cases and

motherboards vary. Refer to your computer’s reference

manual for further information, if needed.

Static Electricity Discharge may permanently damage

your system. Discharge any static electricity build up in

your body by touching your computer’s case for a few

seconds. Avoid any contact with internal parts and

handle cards only by their external edges.

1. Turn OFF the power to your computer and any

other connected peripheral devices.

2. Unplug the power cord from the back of the

computer.

3. Remove your computer’s cover.

4. Remove the slot bracket from an available PCI slot.

5. Change JP1 jumper settings to the desired voltage

only if your serial device needs additional power

from the serial port. However, most serial devices

do not require additional power. For more

information go to Figure 1 on page 2. The jumper

can be removed if power output is not required.

6. To install the card, carefully align the card's bus

connector with the selected PCI slot on the

motherboard. Push the board down firmly, but

gently, until it is well seated.

7. Replace the slot bracket's holding screw to secure

the card.

8. Replacethecomputercoverandreconnectthepower

cord.

Driver Installation

This section provides information on how to install the

CyberSerial PCI drivers.

DOS

1. Boot up DOS and insert the driver CD.

2. Copy OXSER.EXE from the DOS folder to your C:

drive.

3. At the C: prompt, type in OXSER io=3e8 and the

serial ports will be set up as COM3.

If your system already comes with 4 serial ports

enabled, type in OXSER io=220 instead and the

ports will be set up as COM5.

4. Copy the OXSER command in step 3 into your

autoexec.bat and restart your system.

Windows95

1. At the Update Device Driver Wizard, click Next.

2. Insert the driver CD, and click Other Locations.

Typein D:\9x,click OK,thenFinish.(Change D:to

match your CD-ROM drive letter)

3. From the Insert Disk window, click OK. When the

Copying Files dialog box appears, type in

D:\9x, then click OK.

4. Restart Windows to complete the installation.

Windows98/98SE

1. At the Add New Hardware Wizard window, click

Next.

2. Select Search for the best driver for your device

(Recommend), then click Next.

3. Select Specify a location, uncheck the other boxes,

insert the driver CD, type in D:\9x,then click Next.

(Change D: to match your CD-ROM drive letter)

4. Click Next, then Finish.

5. Repeat steps 1-4.

6. Restart Windows to complete the installation.

WindowsME

1. AttheAddNewHardwareWizard,chooseSpecify

the location of the driver (Advanced), then click

Next.

2. Check Specify a location, uncheck the other box,

insertthedriverCD,typeinD:\Me,thenclickNext.

(Change D: to match your CD-ROM drive letter)

3. Click Next and Finish.

4. Repeat steps 1 and 2.

5. Click Next, Next, then Finish

6. Restart Windows to complete the installation.

ToVerifyWindows95/98/98SE/MEInstallation

1. Fromthemaindesktop,doubleclickMyComputer,

ControlPanel,System,thenclickDeviceManager.

2. Double click Ports (COM & LPT), CyberSerialPCI

16Cxxx... should be displayed.

3. Double click Multi-function adapters, SIIG

CyberPro 1S PCI board and PCI Function should

be displayed.

WindowsNT4.0

1. From the desktop click Start, then Run.

2. Insert the driver CD, type in

D:\NT4\install_serial.exe, then click OK.

(Change D: to match your CD-ROM drive letter)

3. Click Next when the Welcome window appears.

4. Choose Install, then click Next.

5. Click Yes, then click Exit.

6. Restart Windows to complete the installation.

ToVerifyWindowsNT4.0Installation

1. Go to Start / Setting / Control Panel,double click

Ports device icon.

2. AnewCOMportwillbeassignedwhensuccessfully

installed.

Windows2000

1. At the Found New Hardware Wizard, click Next.

2. Select Search for a suitable driver for my device

(recommended) and click Next.

3. SelectSpecifyalocation,unchecktheotheroptions

and click Next.

4. InsertthedriverCD,typeinD:\2000,thenclickOK.

(Change D: to match your CD-ROM drive letter)

5. Click Next and Finish.

6. Repeat steps 1-5 two more times

7. Restart Windows to complete the installation.

WindowsXP

1. AttheFoundNewHardwareWizard,chooseInstall

from a list or specific location (Advanced),then

click Next.

2. Insert the driver CD, check Include this location in

the search,uncheck the other check box, type in

D:\XP,and click Next. (Change D: to match your

CD-ROM drive letter)

3. IftheHardwareInstallationwindowpopsup,click

Continue Anyway, then Finish. Our driver has been

testedforstabilityandcompatibility.

4. Repeat steps 1-3 two more times

5. Restart Windows to complete the installation.

WindowsServer2003

1. AttheFoundNewHardwareWizard,chooseInstall

from a list or specific location (Advanced),then

click Next.

2. Insert the driver CD, check Include this location in

the search,uncheck the other check box, type in

D:\2003,and click Next. (Change D: to match your

CD-ROM drive letter)

3. IftheHardwareInstallationwindowpopsup,click

Continue Anyway, then Finish. Our driver has been

testedforstabilityandcompatibility.

4. Repeat steps 1-3 two more times.

5. Restart Windows to complete the installation.

ToVerifyWindows2000/XP/2003Installation

1. RightclickMyComputer,clickManage,thenselect

Device Manager.

2. Click on the + (plus sign) in front of Ports (Com &

LPT), CyberSerial PCI 16Cxxx... should be

displayed.

3. Double click Multifunction adapters, SIIG

CyberPro 1S PCI board should be displayed.

Linux Kernel 2.4.x or later

1. Open the terminal.

2. Type setserial -bg /dev/ttyS* and hit <enter> to

show the current serial ports installed. SIIG board

will be set up at the next available address. For

example, if your system comes with /dev/ttyS0

and /dev/ttyS1, set up SIIG board as /dev/tty2.

3. Type lspci -v and hit <enter>. This command

displays the CyberSerial Dual PCI's information

similar to the example listed below. This

information is needed to configure the serial ports.

-02:0b.0Serialcontroller:OxfordSemiconductor

Ltd EXSYS EX-41092 Dual 16950 Serial ....

- Subsystem: SIIG Inc: ....

- Flags: medium devsel, IRQ 9

- I/O ports at a000 [size=32]

- Memory at ed800000 (32-bit, ...) ....

- I/O ports at 9800 [size=32]

- Memory at ed000000 (32-bit, ...) ....

- Capabilities: [40] Power Management ....

4. Edit the startup file and add this command line at

end of the startup file.

- setserial /dev/ttyS2 port 0xa000 irq 9 uart 16950.

Note: ttyS value, I/O port address and irq should

be different from one system to another. These

values should be based on the results you get from

steps 2 & 3.

5. Save the startup file and restart your system.

Changing COM Port Address

Some serial devices need a specific COM port in order to

work. If your serial device works properly, do not

change this setting.

Windows95/98/98SE/ME

1. From the Device Manager window double click

Ports(COM & LPT), then double click the

CyberSerial PCI serial port you want to change.

2. Click Settings tab, click the down arrow that is next

tothePortNameboxandselectaCOMaddressthat

is not currently in use.

3. Click OK, then close Device Manager to save the

changes.

Windows2000/XP/Server2003

1. From the Device Manager window double click

Ports(COM & LPT), then double click the

CyberSerial PCI serial port you want to change.

2. Click Settings tab and click Advanced.

3. Click the down arrow that is next to the COM Port

numberboxandselectaCOMportthatisnotinuse.

Click OK.

4. Click OK, then close Device Manager to save the

changes.

Andere Handbücher für CyberSerial Dual PCI

Inhaltsverzeichnis

Andere SIIG PCI-Karte Handbücher

SIIG

SIIG NN-830012-S2 Bedienungsanleitung

SIIG

SIIG LB-US0314-S1 Bedienungsanleitung

SIIG

SIIG SATA II-150 PCI Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCIe Bedienungsanleitung

SIIG

SIIG DP 4-Port USB 3.0 PCIe i/e Bedienungsanleitung

SIIG

SIIG Hi-Speed USB 5-Port PCI Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

SIIG

SIIG DP SuperSpeed USB 3.0 2-Port PCIe i/e Bedienungsanleitung

SIIG

SIIG SC-SAE012-S2 Bedienungsanleitung

SIIG

SIIG SC-SAE212-S2 Bedienungsanleitung

SIIG

SIIG SC-SA3012-S1 Bedienungsanleitung

SIIG

SIIG Low Profile PCI-2S Bedienungsanleitung

SIIG

SIIG SIIG 2S1P Combo-Value Bedienungsanleitung

SIIG

SIIG CyberPro PCI 8S Bedienungsanleitung

SIIG

SIIG LB-GE0114-S1 Bedienungsanleitung

SIIG

SIIG SC-SA4M12 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Bedienungsanleitung

SIIG

SIIG DP CyberSerial 4S PCIe Bedienungsanleitung

SIIG

SIIG Low Profile USB 2.0 Bedienungsanleitung

SIIG

SIIG SoundWave 7.1 PCI Bedienungsanleitung

SIIG

SIIG CyberPro PCI 4S Bedienungsanleitung

SIIG

SIIG Cyber 1S1P PCI Bedienungsanleitung

SIIG

SIIG 8000 Plus Bedienungsanleitung

SIIG

SIIG Serial ATA 4-Channel PCI Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung

Alpha Networks

Alpha Networks WMP-A13V Bedienungsanleitung

Acqiris

Acqiris SA230E Bedienungsanleitung