Sirius Satellite Radio SUT951 Bedienungsanleitung

INSTALLATION

INSTRUCTIONS

CARE AND USE MANUAL FOR:

Ceiling Hood

Models covered by this instructions:

SUT950 - SUT951 - SUT958

*** BEFORE INSTALLATION ***

ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED

DURING SHIPPING

*** SHIPPING DAMAGE ***

MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

WARNING

Thank you for purchasing a Sirius Range Hood.

Please read all the instructions in this manual before

installing the appliance.

Save these instructions for future reference.

Only use this appliance as an exhaust ventilation system for the removal of

cooking vapors. DO NOT use to expel ammable substances or any other

materials or vapors.

The installation procedures in this manual are intended for qualied instal-

lers, service technicians or persons with similar qualied background.

DO NOT attempt to install this appliance yourself.

Ensure that electrical power is turned o at source before commencing in-

stallation. All electrical wiring must be properly installed, insulated and

grounded and conform to all applicable codes and standards.

Make sure all existing duct work is clean of grease build up, or duct work

should be replaced, if necessary, to avoid the possibility of a grease re.

Check all joints on ductwork to ensure proper connection and all joints

should be properly taped. Be careful when cutting through ceilings or walls

not to damage any hidden pipes or electrical wiring. Ensure your kitchen has

sucient air return vents to replace the exhausted air.

Fan ducts should always be vented to the outside of your home and never

into spaces within walls, ceilings, lofts or attics. Only use rigid, smooth

steel for ducting. The exhaust point of the blower requires a 6” or 8” round

connection.

TABLE OF CONTENTS

BEFORE YOU BEGIN 4

DUCTING 4

ELECTRICAL 5

Electrical Supply 5

INSTALLATION 6

Before the installation 6

Panels opening 6

Installation 6

OPERATING PROCEDURES 8

General Advice 8

Technical data 9

Standard conguration 9

Generating a new transmission code 9

Learning the new transmission code 9

MAINTENANCE 10

Cleaning the Filter 10

Cleaning the Hood 10

WARRANTY 12

BEFORE YOU BEGIN: It is advisable to test

run the range hood before installation.

BEFORE STARTING – please read this en-

tire document and ensure you are fully

conversant with the require-ments and

limitations. These units weigh approxi-

mately 125lbs and therefore require a

minimum of two people to install.

Recommended height from cook top to

underside of hood = 30” for gas, 25” for

electric.

BEFORE YOU BEGIN

The manufacturer declines all responsi-

bility in the event of failure to observe the

instructions given here for installation,

maintenance and suitable operation of

the product. The manufacturer further

declines all responsibility for injury due

to negligence and the warranty of the

unit automatically expires due to impro-

per maintenance and/or installation.

Use the shortest most direct ductwork

route possible. Only use metal ducting

- plastic ducting is generally not permit-

ted by code. Do not use exible metal

ducting as the ridges of the ducting cau-

se severe air turbulence and will signi-

cantly reduce the eciency of any hood

-THIS TYPE OF DUCTING WILL REDUCE

EFFICIENCY BY 50%.

Vent hoods may interrupt the proper ow

of exhaust gases from re-places, gas

furnaces and gas water heaters. To mini-

mize the risk of drawing these lethal ga-

ses back into the home please follow the

heating equipment manufacturers safety

standards and guidelines. Refer to NFPA

and ASHRAE for additional information.

DUCTING

If vented externally, 6” / 150mm round

ducting must be available for the hood

through the ceiling, in line with the cen-

tral vertical axis of the range hood.

If it’s gas range or cook top recomman-

ded 8”.

This unit must have it’s own ductwork.

Do not under any circumstances vent this

unit into any other ductwork or exhaust

ducting in the building.

Furthermore, please read carefully all of

the following installation instructions.

- Use an exhausting pipe whose maxi-

mum length does not exceed 5 meters.

- Limit the no. of elbows in the piping,

since each elbow reduces the air capacity

of 1 linear meter. (Ex.: if you use no. 2 x

90 ° elbows, the length of piping must

not exceed 3 meters).

- Avoid abrupt direction changes.

- Use a 6”/8” mm constant diameter

pipe for the whole length.

- Use piping approved by standards in

force.

Electrical Supply.

This appliance requires 120V/60Hz,

3amp electrical supply – ensure an ap-

propriately qualied person completes

the electrical hook-up. The connection

point for the electrical supply is at the top

of the unit, therefore the electrical supply

must be run down from the ceiling alon-

gside the ductwork.

All electrical and venting hook-ups must

be in place before commencing installa-

tion of the hood-fan.

ELECTRICAL

WARNING: All electrical work must be

performed by a qualied electrician.

Please ensure that the appropriate electri-

cal codes or prevailing local building co-

des and ordinances are adhered to.

Ensure that the electricity supply is di-

sconnected at source. Do not use an ex-

tension cord or adapter plug with this

appliance.

This appliance must be grounded. Con-

nect to a properly grounded branch

circuit, protected by a 15 amp circuit

breaker.

INSTALLATION

BEFORE THE INSTALLATION

This models can be used only if connec-

ted with external motors produced by

the same manufacturer.

PANELS OPENING

It is possible to open the steel panels,

which cover the grease lters, by slightly

pulling on a side of the panel itself, as

shown in Fig. 1.

Draw the outline of the hole to house the

ceiling-mounted hood on the solid ceiling

as shown in Fig. 3 according to the model

chosen.

Make 4 holes in the ceiling according to the

dimensions as shown in Fig. 4, place the

metric plugs provided in the holes.

SUT958: 34” 4/64 x 15” 60/64

distance of 12” between the ceiling and the

false ceiling.

After having chosen the most suitable po-

sition, prepare the ducting: an air outlet

connection piece, with a diameter of 6” to

be installed in the side selected, is provided

with the appliance.

Leave any unused exhaust outlets closed.

As shown in g.2.

To achieve the complete opening of

panels, you need to release the safety

chains, by using the appropriate spring

catches.

For proper working, it is recommended

to install the appliance at a distance of

83” from the oor.

Before starting the appliance installation,

please check that all components are not

damaged, in such a case contact your

retailer and do not carry out installation.

INSTALLATION

Fit a false ceiling with an opening that

has the following dimensions:

SUT950: 57” 43/64 x 37” 63/64

distance of 12” between the ceiling and

the false ceiling;

SUT951: 41” 59/64 x 26” 12/64

Open the stainless steel panels and re-

move the grease lters in order to avoid

damaging them in any way and too al-

low installation; screw the threaded bars

provided into the plugs as shown in g.5.

The threaded bars are 9” 27/32 long

and serve to install the ceiling-mounted

hood at a distance from the solid ceiling

of between 10” 40/64 and 14” 9/16 as

shown in g. 6.

MAX

10” 40/64 MAX

14” 36/64

in case of a larger gap between the hood

and the ceiling, you need to use longer

threaded bars.

Connect the power supply into the metal

box placed inside the hood as shown in

g. 7.

and connect the air outlet pipe.

Do not x the ducting to the outlet with

screws - use DUCT TAPE;

place the ceiling-mounted hood into the

niche, the outer edge of the hood needs

to be perfectly ush with the false ceiling.

Insert the plates and nuts provided on

the threaded bars, making sure to tighten

them securely, as shown in Fig. 8; ret

the grease lters and lter cover panels.

OPERATING PROCEDURES

Read all the instructions before opera-

ting the appliance. Save these instruc-

tions for future reference.

General Advice.

Ensure that the grease lters are in place.

Without these components, operating

blowers could catch on to hair, ngers

and loose clothing. Keep fan, lters and

surfaces clean of grease and fat. Always

turn hood fan ON when cooking. NEVER

leave cooking unattended.

NEVER dispose cigarette ashes, ignitable

substances or any foreign objects into

blowers.

Cooking that generates ame is not re-

commended as this hood is equipped

with a thermal overload that will shut

down the motor if it senses excessive

heat.

When frying, oil in the pan can easily

overheat and ignite. Heat oil slowly in an

appropriately sized pot (covering the en-

tire burner) to reduce the risk of boiling

over and burning.

In the event of a range top grease re,

observe the following:

Switch OFF the range hood. Turn o

the cook top then smother ames with

a close tting lid, cookie sheet or other

metal tray. If the ames do not go out

immediately.

EVACUATE AND CALL THE FIRE DEPART-

MENT.

Never pick up a aming pan – you may

be burned. DO NOT USE WATER inclu-

ding wet dishcloths or towels, as a vio-

lent steam explosion may occur.

SUT950 - SUT951 - SUT958

RC001

RADIO CONTROL

Radio control used for the remote operation

of ducted cooker hoods.

TECHNICAL DATA

- Alkaline battery powered: 12 V mod. 23 A

- Operating frequency: 433.92 Mhz

- Combinations: 32.768

- Max. consumption: 25 mA

- Operating temperature: -20 ÷ + 55 °C

- Dimensions: 120 x 45 x 15 mm.

OPERATING DESCRIPTION

The transmitter is equipped with 5 buttons

for cooker hood management, as specied

below:

: Light ON/OFF command.

: Motor ON (speed level 1) / OFF command.

: Reduce speed.

: Increase speed.

: 10-minute timer.

INITIAL OPERATING CONDITION

The manufacturer supplies the radio control

unit ready to be used with codes preset in the

Factory

OPERATION MODE

Standard conguration:

Standard conguration requires all “cooker

hoods – radio control - system” to be provi-

ded with the same transmission code. In the

event two cooker hoods – radio control sy-

stem are installed in the same room or near-

by, each system may aect the operation of

the another. Therefore, the code of one radio

control system must be changed.

Generatiing a new transmiissiion code:

The radio control system is provided with

preset codes. Should new codes be required,

proceed as follows: Press simultaneously but-

tons:

for two seconds. When Leds light on, press

buttons:

(within 5 seconds). Leds ashing 3 times in-

dicate

the procedure is completed.

WARNING! This operation deletes perma-

nently the preset codes.

Learniing the new transmiissiion code:

Once the transmission code is changed in the

radio control unit, the electronic central unit

of the cooker hood must be made to set the

new code in the fol- lowing way:

Press the main power-o button of the hood

and then restore power to the electronic con-

trol unit. Within the next 15 seconds, press

the Liight Button to synchronise the cen-

tral unit with the code.

Reset of the Factory coniguratiion:

To restore the Factory conguration, follow

the pro- cedure described below: press si-

multaneously buttons:

for 2 seconds. When Leds light on, press but-

tons:

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SILT-26 Series Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SDD2EMIX60 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SEM1 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU-DD20 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923 520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUF1 Handbuch

Sirius Satellite Radio

Sirius Satellite Radio SUF1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT966 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 EM WIFI Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SM923L520 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT980 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU35 TC Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT972 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLTC EM 107 G900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Essence S-DD 16 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-28 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH1 Benutzerhandbuch

Sirius Satellite Radio

Sirius Satellite Radio SL85 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT950 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU107 Leitfaden

Sirius Satellite Radio

Sirius Satellite Radio FSED Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT962 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUT950 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch