Sirius Satellite Radio SUT958 H200 Bedienungsanleitung

INSTALLATION

INSTRUCTIONS

Models covered by this instructions:

SUT958 H200

*** BEFORE INSTALLATION ***

ENSURE THERE IS NO VISIBLE OR HIDDEN DAMAGE SUSTAINED DURING SHIPPING

*** SHIPPING DAMAGE ***

MUST BE REPORTED WITHIN 5 DAYS OF RECEIPT

Ceiling Hood

CARE AND USE MANUAL FOR:

WARNING

Thank you for purchasing a Sirius Range Hood.

Please read all the instructions in this manual before

installing the appliance.

Save these instructions for future reference.

Only use this appliance as an exhaust ventilation system for the re-

moval of cooking vapors. DO NOT use to expel ammable substan-

ces or any other materials or vapors.

The installation procedures in this manual are intended for quali-

ed installers, service technicians or persons with similar qualied

background.

DO NOT attempt to install this appliance yourself.

Ensure that electrical power is turned off at source before commen-

cing installation. All electrical wiring must be properly installed, insula-

ted and grounded and conform to all applicable codes and standards.

Make sure all existing duct work is clean of grease build up, or duct

work should be replaced, if necessary, to avoid the possibility of a

grease re. Check all joints on ductwork to ensure proper connec-

tion and all joints should be properly taped. Be careful when cutting

through ceilings or walls not to damage any hidden pipes or electrical

wiring. Ensure your kitchen has sufcient air return vents to replace

the exhausted air.

Fan ducts should always be vented to the outside of your home and

never into spaces within walls, ceilings, lofts or attics. Only use rigid,

smooth steel for ducting. The exhaust point of the blower requires a

6” round or 8” connection.

TABLE OF CONTENTS

BEFORE YOU BEGIN 4

DUCTING 4

ELECTRICAL

Electrical Supply 5

INSTALLATION 6

OPERATING PROCEDURES

General Advice 8

Technical data 9

Standard conguration 9

Generating a new transmission code 9

Learning the new transmission code 9

MAINTENANCE

Cleaning the Filter 11

Cleaning the Hood 11

Substitution of the LED bar 11

WARRANTY SERVICE 12

BEFORE YOU BEGIN: It is advisable to

test run the range hood before installa-

tion.

BEFORE STARTING – please read this

entire document and ensure you are fully

conversant with the require-ments and li-

mitations. These units weigh approximately

125lbs and therefore require a minimum of

two people to install.

Recommended height from cook top to un-

derside of hood = 30” for gas, 25” for elec-

tric.

BEFORE YOU BEGIN

The manufacturer declines all responsibility

in the event of failure to observe the instruc-

tions given here for installation, maintenan-

ce and suitable operation of the product. The

manufacturer further declines all responsibi-

lity for injury due to negligence and the war-

ranty of the unit automatically expires due

to improper maintenance and/or installation.

Use the shortest most direct ductwork rou-

te possible. Only use metal ducting - plastic

ducting is generally not permitted by code.

Do not use exible metal ducting as the rid-

ges of the ducting cause severe air turbulen-

ce and will signicantly reduce the efcien-

cy of any hood -THIS TYPE OF DUCTING

WILL REDUCE EFFICIENCY BY 50%.

Vent hoods may interrupt the proper ow of

exhaust gases from re-places, gas furna-

ces and gas water heaters. To minimize the

risk of drawing these lethal gases back into

the home please follow the heating equip-

ment manufacturers safety standards and

guidelines. Refer to NFPA and ASHRAE for

additional information.

DUCTING

If vented externally, 6” / 150mm round duc-

ting must be available for the hood through

the ceiling, in line with the central vertical

axis of the range hood.

If it’s gas range or cook top recommanded

8”.

This unit must have it’s own ductwork. Do

not under any circumstances vent this unit

into any other ductwork or exhaust ducting

in the building.

Furthermore, please read carefully all of the

following installation instructions.

- Use an exhausting pipe whose maximum

length does not exceed 5 meters.

- Limit the no. of elbows in the piping, since

each elbow reduces the air capacity

of 1 linear meter. (Ex.: if you use no. 2 x 90 °

elbows, the length of piping must not exceed

3 meters).

- Avoid abrupt direction changes.

- Use a 6”/8” mm constant diameter pipe for

the whole length.

- Use piping approved by standards in force.

Electrical Supply.

This appliance requires 120V/60Hz, 3amp

electrical supply - ensure an appropriately

qualied person completes the electrical ho-

ok-up. The connection point for the electrical

supply is at the top of the unit, therefore the

electrical supply must be run down from the

ceiling alongside the ductwork.

All electrical and venting hook-ups must be in

place before commencing installation of the

hood-fan.

ELECTRICAL

WARNING: All electrical work must be

performed by a qualied electrician.

Please ensure that the appropriate electrical

codes or prevailing local building codes and

ordinances are adhered to.

Ensure that the electricity supply is discon-

nected at source. Do not use an extension

cord or adapter plug with this appliance.

This appliance must be grounded. Connect

to a properly grounded branch circuit, pro-

tected by a 15 amp circuit breaker.

Take the product out of the packaging and pla-

ce it on a suitable surface: we suggest to use a

soft material, such as a sponge or a cloth.

Open the glass panel, rotating it as shown in

Fig. 1, and remove the grease lters.

INSTALLATION

insert the plastic plugs into the holes made,

and then x the ceiling brackets as shown in

Fig. 3.

The ceiling brackets are telescopic , so

their height can be adjusted at 2” 3/8 (2” 3/4

SLT958 h200) between the ceiling and the

hood.

You can choose one of the three air out -

lets shown in Fig. 4: t the air outlet plastic

ange in the desired outlet; the remaining

outlets shall be closed with the specicmetal

caps, as shown in g. 4.

g. 1

g. 2

g. 3

g. 4

A recess shall be created , where the ap-

pliance will be placed, which shall have a

34” 1/16 x 15” 15/16 (865mm x 405mm)

rectangular opening and depth ranging from

6” to 10” 5/8.

THE RECESS SHALL BE MADE AFTER

INSTALLING THE APPLIANCE AND ESPE-

CIALLY AFTER CONNECTING THE AIR

OUTLET PIPE

The recess shall be provided with a socket

and a round pipe of 6” diameter, or a similar

section, for the air outlet.

Drill the holes on the ceiling, as shown in

Fig. 2.

Bring the hood close to the brackets pre-

viously xed and then connect the applian-

ce to the supply mains.Secure the hood to

the ceiling, by using the screws supplied, as

shown in Fig. 5.

EXTERNAL MOTOR VERSION

Connect the external motor cable to the ter-

minal board found inside the plastic box of

the appliance wiring . Make sure to respect

the colors of cables when performing the

electrical connection (g. 6).

g. 5

g. 6

OPERATING PROCEDURES

Read all the instructions before operating

the appliance. Save these instructions for

future reference.

General Advice.

Ensure that the grease lters are in place.

Without these components, operating blo-

wers could catch on to hair, ngers and lo-

ose clothing. Keep fan, lters and surfaces

clean of grease and fat. Always turn hood

fan ON when cooking. NEVER leave coo-

king unattended.

NEVER dispose cigarette ashes, ignitable

substances or any foreign objects into blo-

wers.

Cooking that generates ame is not re-

commended as this hood is equipped with

a thermal overload that will shut down the

motor if it senses excessive heat.

When frying, oil in the pan can easily

overheat and ignite. Heat oil slowly in an

appropriately sized pot (covering the entire

burner) to reduce the risk of boiling over

and burning.

In the event of a range top grease re, ob-

serve the following:

Switch OFF the range hood. Turn off the

cook top then smother ames with a close

tting lid, cookie sheet or other metal tray. If

the ames do not go out immediately.

EVACUATE AND CALL THE FIRE DE-

PARTMENT.

Never pick up a aming pan – you may be

burned. DO NOT USE WATER including

wet dishcloths or towels, as a violent steam

explosion may occur.

RC001

RADIO CONTROL

Radio control used for the remote operation of

ducted cooker hoods.

TECHNICAL DATA

- Alkaline battery powered: 12 V mod. 27A

- Operating frequency: 433.92 Mhz

- Combinations: 32.768

- Max. consumption: 25 mA

- Operating temperature: -20 ÷ + 55 °C

- Dimensions: 130x45x15 mm.

OPERATING DESCRIPTION

The transmitter is equipped with 5 buttons for coo-

ker hood management, as specied below:

: Light ON/OFF command.

: Motor ON (speed level 1) / OFF command.

: Reduce speed.

: Increase speed.

: 10-minute timer.

INITIAL OPERATING CONDITION

The manufacturer supplies the radio control unit

ready to be used with codes preset in the Factory

OPERATION MODE

Standard conguration:

Standard conguration requires all “cooker hoods

– radio control - system” to be provided with the

same transmission code. In the event two cooker

hoods – radio control system are installed in the

same room or nearby, each system may affect the

operation of the another. Therefore, the code of

one radio control system must be changed.

Generating a new transmission code:

The radio control system is provided with preset

codes. Should new codes be required, proceed

as follows: Press simultaneously buttons:

for two seconds. When Leds light on, press but-

tons:

(within 5 seconds). Leds ashing 3 times indicate

the procedure is completed.

WARNING! This operation deletes permanen-

tly the preset codes.

Learning the new transmission code:

Once the transmission code is changed in the ra-

dio control unit, the electronic central unit of the

cooker hood must be made to set the new code in

the fol- lowing way:

Press the main power-off button of the hood and

then restore power to the electronic control unit.

Within the next 15 seconds, press the Liight But-

ton to synchronise the central unit with the

code.

Reset of the Factory conguration:

To restore the Factory conguration, follow the

procedure described below: press simultaneously

buttons:

for 2 seconds. When Leds light on, press buttons:

(within 5 seconds). Leds ashing 6 times indicate

the procedure is completed.

WARNING! This operation deletes permanen-

tly the preset codes.

Emergency button:

In the event that the radio control does not work,

use the emergency button to switch the appliance

off. After any necessary repairs have been perfor-

med, reset the emergency button.

WARNING

The battery should be replaced every year to

guarantee the optimal range of the transmitter.

To replace the exhausted battery, take the pla-

stic lid off, remove the battery and replace it

with a new one, observing the correct battery

polarities.

Used batteries should be discarded in special

collection bins.

The below product:

RC001 Radio Controll

complies with the specications set out in the

Directive RED 2014/53/EU.

WARNING

Any adjustments or modications which have

not been expressly approved by the holder of

the legal conformity certicate may invalidate

the user’s rights relating to the operation of

the device.

Rev. 0 26/08/14

The products are endowed with an electronic de-

vice which allows the automatic switching off after

4 hours working from the last operation.

Warning The battery should be replaced eve-

ry year to guarantee the optimal range of the

transmitter. To replace the exhausted battery,

take the plastic lid off, remove the battery and

replace it with a new one, observing the cor-

rect battery polarities. Used batteries should

be discarded in special collection bins.

Filter requires washing indicator: after 30 hours

of use, all the buttons will light up to remind you

that the grease lter should be cleaned. Follow

the instructions for cleaning lters in this booklet.

Once the grease lters have been cleaned and

replaced, reset by pressing the timer button (F).

Do not rely solely on this indicator. Generally, the

grease lter should be washed on a regular basis

to avoid grease lter res.

The blower should be turned on for approximately

5 minutes before cooking in order to establish air

currents upward through the hood. Use the low

speeds for normal use and the higher speeds for

strong odors and fumes.

Inhaltsverzeichnis

Andere Sirius Satellite Radio Dunstabzugshaube Handbücher

Sirius Satellite Radio

Sirius Satellite Radio SL906 L 1500 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL85 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio Valentina SLT977EMEL Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT105 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU906 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SL83 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU1 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUTC919 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT950 EM Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio S-DDH3 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU900 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT950 EM Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-21 B Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL906 DL Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU909 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SLEM80 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SL920 FRESCO Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio Valentina SLT958EM Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SIU3 Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SU-DD20 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SLT955 Kurzanleitung

Sirius Satellite Radio

Sirius Satellite Radio SILT-26 Series Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio ALFRESCO SL80 Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch