Soleus Air FEA-12HP Bedienungsanleitung

12,000 BTU

Portable Air Conditioner

with Heat Pump

Operating

Instruction

V190102

Thank you for choosing a Soleus Air Portable Air Conditioner. This owner’s manual will provide

you with valuable information necessaryfor the proper care and maintenance of your new product.

Please take a few moments to thoroughlyread the instructions and familiarize yourself with all the

operational aspects of your new Soleus Air Portable Air Conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the

store name/location, date purchased, and serial number below:

Store Na

me:

Location:

Purc

ed:

erial

Number

(

located

bac

k of u

nit):

IMPORTANT INSTRUCTIONS

Before installing and using your portable air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference.

1) Always place the unit on a level surface.

2) Never use or store gasoline or other flammable vapor or liquid near this unit unless instructed by this manual.

3) Maintain at least 10 inches (25 cm) clearance space around this unit. Do not block or cover air inlet or outlet

grilles.

4) The unit must be connected to a correctly grounded power supply.

5) Do not start or stop the unit by inserting or pulling out the power plug.

6) Do not use an adapter plug or extension cord.

7) Do not use the unit in the immediate surroundings of a bath, a shower or a swimming pool.

8) Do not insert anything into the air outlet. Do not obstruct air inlet or outlet grills unless instructed by this

manual.

9) Do not let children play near this unit.

10) Always inspect the cord for signs of damage before use. If the power cord is damaged, it must be replaced by

the manufacturer or a qualified service technician.

11) When cleaning the unit, always turn the unit off and unplug the power cord.

12) Do not mix old and new batteries in the remote control.

Do not mix Alkaline, Standard (Carbon - Zinc) or Rechargeable (Nickel - Cadmium) Batteries.

SPECIFICATIONS

The cooling capacity is measured at an ambient temperature of DB 95˚F, WB 83 ˚F.

Noise level is measured at 3.28 ft away from the front of the unit, when the unit is in cooling mode.

Power consumption is measured when the fan runs at the highest speed setting.

These specifications are for reference only. For actual data, please refer to the rating label on the back

of the unit.

If the environment temperature is higher than the max operating temperature or lower than the minimum

operating temperature, the air conditioner may not work properly.

Model Number

FEA-12HP

Cooling Capacity

12,000 BTU

Heating Capacity

10,000 BTU

Dehumidifier Capacity

132 Pints/Day

Cooling Power Usage

1250 Watts/10.6 Amps

Heating Power Usage

1150 Watts/10.3 Amps

Air Flow Volume (H/M/L)

206/196/165 CFM

Power Source

115 V / 60 HZ

Sound Pressure Level

53/52/51 dB(A)

Product Weight

59.4 Lbs.

Operating Temperature

64℉-90℉(Cooling)/55℉-81℉(Heating)

Product Dimension (W x D x H)

17.61” x 14.56” x 28.15”

Refrigerant

R-410A

LCDI POWER CORD AND PLUG

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord

and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded

flexible cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.

The cord will remain de-energized until the device has been manuallyreset. This is intended to reduce the

risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded, and they

must be considered a shock hazards if exposed. The cord shield must not be connected to ground or to any

exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:

1. Plug power cord into wall outlet

2. Press TEST Button, circuit should trip, cutting power to the air conditioner

3. Press RESET button for use

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the air

conditioner or attempt to reset the LCDI Plug. Contact Customer Service for troubleshooting

recommendations.

RESET

TEST

Note: Your unit’s power cord may differ from the one shown.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externallyconnected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

ALTERNATIVE LCDI POWER CORD AND PLUG

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord

and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexible

cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.

The cord will remain de-energized until the device has been manually reset. This is intended to reduce the

risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they

must be considered a shock hazards if exposed. The cord shield must not be connected to ground or to any

exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:

1. Plug power cord into wall outlet. The LED light will turn on.

2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,

the LED light will turn off.

3. Press RESET button to restore power to the machine. Once power is restored, the LED light

will turn on again.

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the

air conditioner or attempt to reset the LCDI Plug. Contact Customer Services for troubleshooting

recommendations.

LED LIGHT

Note: Your unit's power cord and plug may differ from the one shown.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externallyconnected loads or supply circuits.

4. The cord and plug are intended for indoor use only.

PRODUCT DIAGRAM

PARTS & ASSEMBLY

PARTS

ASSEMBLY & INSTALLATION

INSTALLATION

When the unit is operating as an air conditioner or dehumidifier, the unit draws in indoor air and exhausts hot air out

of the room to complete the air exchange. When the unit is operating in fan mode no outdoor air exchange takes

place. The window kit and exhaust hose do not need to be installed when the unit is used as a fan.

NOTE: The supplied window kit can be installed in sliding windows and sliding glass doors up to 4.6 ft. long

(approximate length).

MOUNTING THE EXHAUST HOSE

Choose a suitable location, near a grounded electrical outlet and suitable window or door. Remove

packaging and locate components.

Extend both ends of the exhaust hose approximately 6 inches.

Screw the window kit adapter onto one end of the exhaust hose counter-clockwise.

Screw the exhaust hose connector onto the other end of the exhaust hose counter-clockwise.

Connect the exhaust hose over the Air Exhaust Hose Discharge Opening on the back of the unit.

Open the window or door and adjust the length of window kit to fit the opening. Then make the kit

fixed.

Attach the window kit adapter of the exhaust hose to the window kit.

WINDOW KIT INSTALLATION

FOR SINGLE HOSE AIR CONDITIONER

The venting kit must be installed for the unit to work correctly in the air conditioner mode, dehumidifying mode, and auto

mode. The venting kit should not be used while the unit is fanning.

The window kit has been designed to fit into most vertical and horizontal window openings.

1. Screw the Exhaust Hose

Connector onto one end of the

Exhaust Hose.

2. Connect the Exhaust Hose

over the discharge opening on

the back of the unit.

4. Attach the Optional Window Kit Adapter Extension to the Window

Kit. Attach the Exhaust Hose to the Window Kit Adapter. Attach the

Optional Window Kit Adapter Extension to the WindowKit Adapter.

Close the window tightly. Your Portable Air Conditioner is good to go.

3. Open the window or door to adjust the length of the

Window Kit to fit the opening. If necessary, mark the kit

and cut one end down to properly fit the opening.

Note:When using the venting system, keep the Exhaust Hose as straight as possible. The Exhaust

Hose can be shortened, but it is not recommendedto increase the length of the Exhaust Hose. DO

NOT use an extension cord with your Portable Air Conditioner.

Note: The Portable Air Conditioner above may differ from the unit described in this manual. The above

directions and images show general directions for Soleus Air single hose Portable Air Conditioners.

WINDOW KIT ASSEMBLY GUIDE

SCREW

PANEL

SCREW

1.Parts:

A) Panel

B) Panel with one exhaust hose opening

C) Panel without exhaust hose opening

D) Pins to lock window kit in place

2. Assembly:

Slide Panel B and C into Panel A and size to window width.

Windows sizes vary. When sizing the window width, be sure that

the window kit assembly is free from gaps and/or air pockets

when taking measurements.

3. Insert the screw into the holes that correspond with the width

that your window requires to ensure that there are no gaps or air

pockets in the window kit assembly after installation.

CONTROL PANEL, DISPLAY, & OPERATING INSTRUCTIONS

CONTROL PANEL

OPERATING INSTRUCTIONS

CONTROL PANEL BUTTONS

1) Power On and Off - Press the POWER button once to manuallyturn the unit on. Press the POWER

button once more to turn the unit off.

2) Mode Selection - Press the MODE Button repeatedly to cycle between the different modes: Air

Conditioner mode, Dehumidifier mode, Heat mode, Fan only mode, and Auto mode. Each press of the

MODE button will light up a different icon on the control panel. The exhaust hose and window kit must

be in- stalled when the unit is in Air Conditioner, Heatmode,Dehumidifier mode, and Auto mode. When

using the unit as a fan, it is not necessary to keep the exhaust hose and window kit connected to the unit.

3) Temperature - Select the desired temperature by pressing either ▲ or ▼key when using the unit in

Air Conditioner mode. The temperature indicator flashes to display the desired temperature setting.

After the temperature is set; the unit will display this temperature setting until it is changed by the user.

The

temperature indicator display shows temperature in Fahrenheit. Under stand-by condition,

pre

hold the ▲ and ▼key to switch between Celsius and Fahrenheit.

4) Timer - Press the TIMER button to set the unit automatically turn On or Off. Press the TIMER button

repeatedly to set timer within 1-24 hours. Once the desire time is displayed, wait for 5 seconds and the

timer will be active. Press the TIMER button or POWER button to cancel the timer.

5) Bucket Full -When the unit cannot evaporate the collected moisture fast enough, the excess water

will collect in a backup water tank located inside the unit. The control panel will display “”(Full

Tank) if this occurs.

6) Louver Direction - This unit has 2-way directional louvers and will swing up and down automatically

when the unit is power on.

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air PH-3-12R-03 Bedienungsanleitung

Soleus Air

Soleus Air MA-9000AH Bedienungsanleitung

Soleus Air

Soleus Air MAC 7500 Bedienungsanleitung

Soleus Air

Soleus Air HCC-C09H26-A Bedienungsanleitung

Soleus Air

Soleus Air PH1-12R-03 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-25ESE-C Bedienungsanleitung

Soleus Air

Soleus Air PS08-01 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-06ESE Bedienungsanleitung

Soleus Air

Soleus Air KFH-12/KFH-12-1 Bedienungsanleitung

Soleus Air

Soleus Air SG-TTW-10ESE Bedienungsanleitung

Soleus Air

Soleus Air PSJ-05-01A Bedienungsanleitung

Soleus Air

Soleus Air Air condioner Bedienungsanleitung

Soleus Air

Soleus Air HCB-P13HP-D Bedienungsanleitung

Soleus Air

Soleus Air LX-140 Bedienungsanleitung

Soleus Air

Soleus Air TTWM1-14H-01 Bedienungsanleitung

Soleus Air

Soleus Air PE2-07R-62 Bedienungsanleitung

Soleus Air

Soleus Air KFTHP-9-ID Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-12E1HP Bedienungsanleitung

Soleus Air

Soleus Air KY-32U Bedienungsanleitung

Soleus Air

Soleus Air WS1-15E-02 Bedienungsanleitung

Soleus Air

Soleus Air KY-34 Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-06SE-C Bedienungsanleitung

Soleus Air

Soleus Air GM-TTW-10HC Bedienungsanleitung

Soleus Air

Soleus Air 3046364 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung