Soleus Air WS4-10EHW-301 Bedienungsanleitung

4010450

V210208

Air conditioner must be upright for 24 hours prior to operating.

This ensures that the compressor will function as intended.

Model

WS4-10EHW-301 10,000 BTU

WS4-10EH7W-301 10,000 BTU

Electronic Hybrid Air Conditioner w/ Heat

Operating Instructions

Thank you for choosing a Soleus Air Hybrid Air Conditioner. This Owner’s Manual will provide

you with valuable information necessary for the proper care and maintenance of your new product.

Please take a few moments to thoroughly read the instructions and familiarize yourself with all the

operational aspects of your new Soleus Air Window Air Conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the

store name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: _____________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT INSTRUCTIONS

PURCHASE INFORMATION

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this manual in a

safe place for future reference. Your safety and the safety of others is very important to us. Please pay attention to

all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove the ground prong.

• Do not use a plug adapter.

• Do not use an extension cord.

• Unplug the air conditioner before servicing.

• Use two or more people to move and install the air

conditioner.

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you or others or even cause death.

All safety messages will directly follow the safety alert symbol and/or the words “DANGER”

or “WARNING.”

All Safety messages alert you of potential hazards, how to reduce the chance of injury, and what

can happen if instructions are not followed correctly.

Failure to immediately follow these in-

structions may cause serious injury or

even death.

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord

and plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexi-

ble cord with no termination on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the

nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.

The cord will remain de-energized until the device has been manually reset. This is intended to reduce the

risk of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they

must be considered a shock hazard if exposed. The cord shield must not be connected to ground or to any

exposed metal.

The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly.

To test:

1. Plug power cord into wall outlet, the LED light will turn on.

2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs, the LED

light will turn off.

3. Press RESET button to restore power to the unit. Once power is restored, the LED light will turn on

again.

If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the air

conditioner or attempt to reset the LCDI Plug. Contact Customer Service for troubleshooting recommenda-

tions.

WARNING:

1. DO NOT press the TEST button while the air conditioner is operating.

2. The TEST and RESET buttons should not be used as “ON” and “OFF” switches.

3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.

4. The cord and plug are intended for

indoor use only.

POWER CORD AND PLUG

RESET

TEST

LED LIGHT

Note: Your unit’s power cord may

differ from the one shown.

PACKAGE CONTENTS

Air Conditioner

(2) - Mounting Block

• Hybrid Air Conditioner (1)

• Remote Control (1)

• AAA Battery (2)

• Window Slider Foam (2)

• Mounting Block (2)

• Window Slider Support Bracket (2)

• Pre-installed Adjustable Support Knob (2)

• Top Foam Sealer (1)

• Bubble Level (1)

• Optional Window Security Bracket

- Security Bracket (1) , Type B Screw (1)

• Owner’s Manual (1)

Remote

Control

2 AAA

Batteries

Top Foam

Sealer

Owner’s Manual

(2) - Window Slider Support Bracket

(2) - Window Slider Foam

(1) - Security Bracket

(1) - Type B Screw (2) - Pre-installed Adjustable Support Knob

Bubble Level

SPECIFICATIONS

• Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

Model WS4-10EHW-301 WS4-10EH7W-301

Power Supply (Ph/V/Hz) 1/115/60 1/115/60

Rated Cooling & Heating Capacity (BTU/h) 10,000 10,000

Cooling & Heating Power Input (Watts) 1080 1080

Rated Current Cooling & Heating (Amperage) 11.4 11.4

CEER 13.0 13.0

Noise Level (dB(A)) 38-48 (Indoor) / 51-63 (Outdoor) 38-48 (Indoor) / 51-63 (Outdoor)

Airflow CFM 165/224/270 165/224/270

Dehumidifying Capacity 65 Pints per day 65 Pints per day

Product Dimensions (W” x H” x D”) 18.7” x 15.2” x 31.8” 18.7” x 15.2” x 26.3”

Package Dimensions (W” x H” x D”) 20.4” x 17.3” x 33.6” 20.4” x 17.3” x 28.1”

Net/Gross Weight (lbs.) 68.6/78.3 64.6/73.6

Refrigerant Type R-410A R-410A

Plug Type NEMA 5-15P NEMA 5-15P

FCC Notice

This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful

interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the device and receiver

Connect the device into an outlet on a circuit different from that to which the receiver is connected

Consult the dealer or an experienced radio/television technician for help .

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equip-

ment. Such modifications could void the user’s authority to operate the equipment.

ELECTRICAL SAFETY

WARNING:

grounding prong!!

Power supply cord with 3-prong grounding

plug and current detection device

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’S MANUAL ARE THE

PRESENATION OF THE MANUFACTURER. NEPO USA HAS NOT CONDUCTED AN INDEPENDENT TEST TO

VERIFY THE INFORMATION AND SPECIFICATIONS PRESENTED HEREWITHIN.

INSTALLATION

Window Preparation

Please read all instructions prior to installing your air conditioner. Two people are recommended to install this product. If a new

electrical outlet is required, have the outlet installed by a qualified electrician before installing the unit.

Before installing the unit, check the dimensions of your window to make sure the air conditioner will fit. This unit is made to fit

inside a standard double-hung window. Make sure the window is in good shape. If not, make repairs prior to installing the unit.

Storm Window Requirements

A storm window frame will not allow the air conditioner to tilt properly which will keep it from draining properly. To

adjust for this, attach a board or piece of wood to the sill. The board or wood piece should have a depth of at least 1 1/2”.

Make sure the board or piece of wood is approximately 1/2” higher than the storm window frame. This will allow the air

conditioner to tilt enough for proper drainage (See FIG. 2).

Prior to Installing the Air Conditioner

1. Check for anything that could block airflow. Check the area outside of the window for things such as shrubs, trees,

or awnings. Check the inside area to make sure curtains, drapes, or blinds will not prevent proper airflow.

2. Check the available electrical outlet. The power supply must be the same as shown on the unit serial nameplate

(located on the left side of the unit, near the front faceplate). Be sure the outlet is close enough for the power cord to

reach.

3. Carefully unpack the air conditioner. Remove all packing material and make sure the floor is protected when remov-

ing. Due to the large size of this air conditioner, two people should move the unit together.

When handling the unit, be careful to avoid cuts from the

sharp metal edges and aluminum fins on the front and rear

coils.

16" MIN

FIG .2

FIG. 1

16" MIN

Model WS4-10EHW-301 WS4-10EH7W-301

Unit Height 15” 15”

Unit Width 18.7” 18.7”

Min. Window Opening Height 16” 16”

Min. Window Width

(Including space needed for window slider) 24" 24"

Max Window Width 48" 48"

Max Window Sill t 12.5” 7”

1. Attach Mounting Blocks on Window Frame (See Fig.1)

1) Remove adhesive from mounting block and place mounting block on

window frame.

2) Press down firmly on the mounting block to secure in place.

3) Then, remove adhesive from the other mounting block and place

mounting block on window frame.

4) Press down firmly on the mounting block to secure in place.

5) The mounting block are now ready to support the Hybrid Air Condi-

tioner.

2. Slide Hybrid Air Conditioner Over Window Sill

1) Open window completely

2) Lift the Hybrid Air Conditioner on either side of the unit and bring it up to the window.

3) Insert the unit into the window until the center of the Hybrid Air Conditioner is over the window sill.

4) Slowly lower the Hybrid Air Conditioner over the window sill so that the unit straddles the wall.

5) Paying close attention to your fingers, completely lower the Hybrid Air Conditioner onto the window sill.

6) Center Hybrid Air Conditioner in the window so that there are equal gaps on either side of the unit.

*Use the adjustable supports to secure the Hybrid AC against

the outside wall. (See Fig.2)

*Use the bubble level to make sure the unit is balanced

when secure on the window sill. When balanced, the bubble should

between the two black lines. (See Fig.3)

3. Attach Window Slider Support Brackets (See Fig.4)

1) Remove adhesive from window slider support bracket.

2) Position support bracket (adhesive-side) against the left-side edge of the Hybrid Air Conditioner at the

point where the window sash will be aligned with the support bracket when closed.

3) Press the support bracket firmly in place and hold for 5 seconds.

4) Repeat these steps on the right-side edge of the Hybrid Air Conditioner.

INSTALLATION

Fig.1

Fig.2

Fig.4

Fig.3

INSTALLATION

4. Install Window Sliders

1) Measure the distance between the Hybrid AC and the window sash, cut window slider foams to length by

using a utility knife so that it fits inside the opening. (See Fig.5)

2) Slide window slider foams into both support brackets on either side of the Hybrid Air Conditioner. (See

Fig.6)

5. Attach Top Foam Sealer

1) Measure the total width of the installation including the window sliders

2) Cut the top foam sealer to length

3) Remove adhesive from the top foam sealer

4) Attach the top foam sealer to the top of the Hybrid Air Conditioner and

window sliders directly below the window sash

5) Close the window sash and seal.

6. Plug in Hybrid Air Conditioner and Power ON

Fig.5

Fig.6

Fig.7

END OF SEASON

Remove the Air Conditioner from the Window (End of Season)

1. Turn the air conditioner off, and disconnect the power cord.

2. Remove the window sliders from either side of the air conditioner.

3. Using a drain pan, unplug the drain plug on the front bottom of the unit to drain any condensation water

in the base of unit.

4. Keeping a firm grip on air conditioner, lift up and remove the air conditioner from the window and

sill.

5. Store parts with the air conditioner in the box.

Single and Double Hung Windows

SECURITY BRACKET

Optional Security Bracket Installation

Your Window Kit also includes an optional security

bracket that can be installed to prevent the window

from being opened from the outside while a Window

Kit is installed.

WIFI APP SETUP *Screenshots shown are from an Apple iOS device. Android devices may differ slightly.

Step 1

Search and download Soleus

Home Comfort from the App

Store or Android Store

Step 2

Step 3

Fill out email address and click the Get Verifi-

cation Code button. (Email will be sent with

confirmation instructions)

Step 4

password and click add

device

Step 5

Choose Large Home Appliances

and Air Conditioner (Wi-Fi)

Step 7

DO NOT TURN ON THE DEVICE.

Hold the Timer button over 3 seconds

until the Wi-Fi indicator is flashing on

the control panel

Step 6

Enter the Wi-Fi name and Password

Step 8

Click Done and all set

Step 9

To use the voice commend function,

click the Pen icon on the right corner

To reset the Wi-Fi module, hold down the

Timer buttons for over 3 seconds until the

beeping sound is heard.

Note: If the device name is unable to be

found from the network list or the device is

un-registered from the APP, the Wi-Fi

module needs to be reset.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air PAC12 Bedienungsanleitung

Soleus Air

Soleus Air KFHIP-09-OD Technisches Datenblatt

Soleus Air

Soleus Air PE2-08R-62 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-05SM Bedienungsanleitung

Soleus Air

Soleus Air KY-32E Bedienungsanleitung

Soleus Air

Soleus Air MAC 7500 Bedienungsanleitung

Soleus Air

Soleus Air PE6-10R-03 Bedienungsanleitung

Soleus Air

Soleus Air HM1-10-32 Bedienungsanleitung

Soleus Air

Soleus Air LX-140 Bedienungsanleitung

Soleus Air

Soleus Air PE3-12R-03 Bedienungsanleitung

Soleus Air

Soleus Air KY2-34 Bedienungsanleitung

Soleus Air

Soleus Air PSH-08-01 Bedienungsanleitung

Soleus Air

Soleus Air KFH-12/KFH-12-1 Bedienungsanleitung

Soleus Air

Soleus Air MA-9000AH Bedienungsanleitung

Soleus Air

Soleus Air PE2-07R-62 Bedienungsanleitung

Soleus Air

Soleus Air MAC 7500 Bedienungsanleitung

Soleus Air

Soleus Air GB-WAC-06SE-C Bedienungsanleitung

Soleus Air

Soleus Air SG-TTW-10ESE Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-12E1HP Bedienungsanleitung

Soleus Air

Soleus Air SPTAC-09H Bedienungsanleitung

Soleus Air

Soleus Air PH5-13R-32D Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-06ESE Bedienungsanleitung

Soleus Air

Soleus Air MAC-12K/10K Bedienungsanleitung

Soleus Air

Soleus Air Air condioner Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung