Sonnet TANGO 2.0 Bedienungsanleitung

Quick Start Guide for Tango 2.0

Compatibility

Tango 2.0 may be used with any Mac®or Windows®OS computer with an

available PCI slot that meets the following requirements:

• Macintosh Computer Requirements:

Power Macintosh®or Macintosh clone computer running

Mac OS®9.0 through Mac OS X Version 10.3.x. Mac OS X

Version 10.2.8 or higher is required for high-speed USB 2.0

support.

• PC Requirements:

IBM PC/AT or compatible desktop computer with Pentium®II

(or equivalent) or better running Windows 2000 or Windows X

Windows 2000 with Service Pack 3 installed or Windows X

with Service Pack 1 (or later) installed is required for high-

USB 2.0 support.

You Should Have

The following items should be included in your product package

• One Tango 2.0 PCI Combo Adapter Card

The following items may be required for installation:

• Medium Phillips screwdriver

• One or more FireWire (IEEE 1394) cables (sold separately)

• One or more USB cables (sold separately)

• One or more USB hubs (sold separately)

System Requirements

The following software drivers are required:

• FireWire driver software*

• USB driver software*

• Tango Firmware Patch—ONLY for installation of the Tango 2.0 in Power

Macintosh 5500 or 6500, or in Twentieth Anniversary Macintosh computers.

(Download the Tango Firmware Patch from www.sonnettech.com/support/tango;

install it before installing FireWire and USB drivers.)

* Depending on your operating system, you may need to install these drivers; instructions follow.

. Support Notes: We recommend you make a backup of important information on your

system’s current hard drive(s) prior to installing new hardware or software.

When handling computer products, you must take care to prevent components from being

damaged by static electricity. Before opening your computer or removing parts from their pack-

ages, always ground yourself first by touching a metal part of the computer, such as a port

access cover, and work in an area free of static electricity; avoid carpeted areas. Handle all elec-

tronic components by their edges, and avoid touching connector traces and component pins.

Technical knowledge may be required to gain access to the expansion card slots in certain

computer models. We recommend you first consult your computer’s user manual. If you feel

you are unable to install the computer hardware, contact a qualified technician.

FireWire®/USB 1.1/2.0 PCI Combo Adapter Card

Remember to register your product online at http://registration.sonnettech.com to be informed of future upgrades and product releases.

Software updates and links are available from the Sonnet web site at www.sonnettech.com. • Online support form available at http://supportform.sonnettech.com

Sonnet Technologies Customer Service hours are Mon.–Fri., 7 a.m.–5 p.m. Pacific Time • Customer Service Phone: 1-949-472-2772 • E-mail: support@sonnettech.com

Sonnet Technologies, Inc., California USA • Tel: 1-949-587-3500 Fax: 1-949-457-6350

©2003 Sonnet Technologies, Inc. Revised 2005.All rights reserved. Sonnet, the Sonnet logotype, Simply Fast, the Simply Fast logotype, and Tango are trademarks of Sonnet Technologies, Inc. Macintosh and Mac are trademarks

of Apple Computer, Inc., registered in the United States and other countries. Other product names are trademarks of their respective owners. Product specifications subject to change without notice. Printed in the USA.

QS-FWUSB2-2G-E-A-011905

The following three pages cover the procedure for installing the Tango 2.0

card into a Mac OS computer. If you have a Windows PC, skip to page 5.

Hardware Installation Preparation

Sonnet strongly recommends that you read the sections in your computer’s

user manual that address PCI card installation, prior to installing the Tango 2.0

card.

Tango 2.0 Card Installation Steps

1. Shut down your computer.

2. Open your computer to access the expansion card area (PCI slots); refer to

your computer’s user manual for speciﬁc information.

3. Locate an available PCI slot inside your computer and remove its port

access cover, if present, from the rear of the computer.

4. Remove the Tango 2.0 card from its packaging.

5. Install Tango 2.0 into the PCI slot; make sure the card is firmly seated

and secured.

6. Close your computer and carefully replace its cover.

Tango Firmware Patch Information

Only For Power Macintosh 5500 and 6500, and Twentieth Anniversary

Macintosh users. You must install an open ﬁrmware patch that enables your

system to fully support Tango 2.0 before you install any FireWire or USB driv-

ers. Log onto the Internet, go to www.sonnettech.com/support/tango, and then

locate and click on the Tango Firmware Patch link. Download the ﬁle, and then

follow the included instructions to install the patch.

FireWire/USB Driver Installation Steps

The following section covers the installation of FireWire and USB driver soft-

ware in Mac OS computers; refer to the heading that describes your setup on

this or the next two pages. If you have a Windows PC, go to page 5 to ﬁnd

Windows driver installation information.

Mac OS X Version 10.2.8 and Higher

Mac OS X Versions 10.2.8 and higher support high-speed USB 2.0, USB 1.1 and

FireWire (400) without the installation of additional drivers; your installation is

complete.

Installation Steps—Mac OS Computers

Support Notes: High-speed USB 2.0 is supported only under Mac

OS X Version 10.2.8 and higher. However, USB 2.0 peripherals are back-

ward-compatible, and Tango 2.0 will support them at USB 1.1 speeds (12 Mb/

sec. maximum) when they are used under Mac OS 9.x through Version 10.2.6.

Installation Steps—Mac OS Computers

Mac 9.2 through OS X Version 10.2.6

The drivers that enable Tango 2.0 to support FireWire (400), and the drivers

that enable it to support all USB devices at USB 1.1 speeds are installed automat-

ically when you upgrade your Mac operating system software to 9.2 through

OS X Version 10.2.6; your installation is complete.

Mac OS 9.1, Existing Installation

Complete these steps only if you installed Mac OS 9.1 before installing the

Tango 2.0 card. Please note, if your system has built-in USB and FireWire ports,

you may skip these steps.

1. Insert the Mac OS 9.1 CD into your computer’s CD-ROM drive. In the

ﬁnder menu, select Special: Restart, then immediately press and hold

down the C key on your keyboard until your system restarts and the

Welcome to Mac OS screen appears.

2. Double-click the Mac OS Install application icon. In the Select Destination

window, click the Select button. Proceed through the next several screens

until you reach the Install Software window. Click the Customize button. In

the Custom Installation and Removal window, deselect all the Software com-

ponent check boxes (click on each check or dash until the box is empty),

except Mac OS 9.1. Click the pop-up menu to the right of Mac OS 9.1.

Change from “Recommended Installation” to “Customized Installation.”

The Select Mac OS 9.1 Features to Install window will appear shortly.

3. Change “Recommended Installation” to “Customized Installation” from

the pop-up menu. Deselect all the feature check boxes except “Network

and Connectivity.” Click the arrow next to “Network and Connectivity”

to view the features. Deselect all the features except “FireWire” and “USB

Adapter Card Support”. Click OK, Start, then Continue to complete the

installation. After the software is installed, quit the Mac OS Install applica-

tion and restart your computer from the hard drive where Mac OS 9.1 is

installed. Your installation is complete.

Mac OS 9.1 (Upgrade From Lower Mac OS Version)

Complete these steps only when upgrading your system to Mac OS 9.1 from a

lower Mac OS version; FireWire and USB driver software will be installed auto-

matically. Please note, if your system has built-in USB and FireWire ports, you

may skip these steps.

1. Insert the Mac OS 9.1 CD into your computer’s CD-ROM drive. In the

ﬁnder menu, select Special: Restart, then immediately press and hold

down the C key on your keyboard until your system restarts and the

Welcome to Mac OS screen appears.

2. Double-click the Mac OS Install application icon. In the Select Destination

window, click the Options button and click the Perform Clean Installation

check box that appears in the subsequent screen. Click the Select but-

ton. Proceed through the next several screens until you reach the Install

Software window. Click OK, Start, then Continue, and complete the

installation. After the software is installed, quit the Mac OS Install applica-

tion and restart your computer from the hard drive where Mac OS 9.1 is

installed. Your installation is complete.

Installation Steps—Mac OS Computers

Mac OS 9 (Existing Installation)

If Mac OS 9.0.x is installed in your computer, you must download and install

the appropriate FireWire and USB driver software. Please note, if your system

has built-in USB and FireWire ports, you may skip these steps.

1. Turn on your computer.

2. Log on to the Internet and type in www.sonnettech.com/support/tango.

3. Locate and click on the link for FireWire and USB drivers.

4. Read the information on the page, then click on each link to download

both drivers.

5. Install the drivers, then restart your computer from the hard drive where

Mac OS 9 is installed. Your installation is complete.

Mac OS 9 (Upgrade From Lower Mac OS Version)

Complete these steps only when upgrading your system to Mac OS 9.0 from a

lower Mac OS version.

1. Insert the Mac OS 9 CD into your computer’s CD-ROM drive. In the

ﬁnder menu, select Special: Restart, then immediately press and hold

down the C key on your keyboard until your system restarts and the

Welcome to Mac OS screen appears.

2. Double-click the Mac OS Install application icon. In the Select Destination

window, click the Options button and click the Perform Clean Installation

check box that appears in the subsequent screen. Click the Select but-

ton. Proceed through the next several screens until you reach the Install

Software window. Click OK, Start, then Continue, and complete the

installation. After the software is installed, quit the Mac OS Install applica-

tion and restart your computer from the hard drive where Mac OS 9 is

installed.

3. Log on to the Internet and type in www.sonnettech.com/support/tango.

4. Locate and click on the link for FireWire and USB drivers.

5. Read the information on the page, then click on each link to download

both drivers.

6. Install the drivers, then restart your computer; your installation is

complete.

Installation Steps—Windows PCs

This page covers the procedure for installing for the Tango 2.0 card into a

Windows PC. If you have a Mac OS computer, return to page 2.

Installation Preparation

Prior to installing Tango 2.0 into your system, you should read the section in

your computer’s user manual that addresses PCI card installation.

Tango 2.0 Card Installation Steps

1. Shut down your computer.

2. Open your computer to access its expansion card area (PCI slots); refer to

your computer’s user manual for speciﬁc information.

3. Remove the Tango 2.0 card from its packaging.

4. Locate an available PCI slot inside your computer and, if present, remove

its port access cover from the rear of the computer.

5. Install the Tango 2.0 card into the PCI slot; make sure the card is ﬁrmly

seated and secured.

6. Close your computer and carefully replace its cover.

FireWire/USB Driver Installation Steps

The following section covers the installation of FireWire and USB driver soft-

ware in a Windows PC. If you have a Mac OS computer, go back to page 2 to

ﬁnd Mac OS driver installation information.

Windows XP

1. Turn on your computer; during Windows startup, Found New Hardware

pop-ups will appear.

2. When the Found New Hardware Wizard window appears, click Next.

3. When the Completing the Found New Hardware Wizard window appears,

click Finish.

4. When the next Found New Hardware Wizard window appears, click Next.

5. When the Completing the Found New Hardware Wizard window appears,

click Finish.

6. A Found New Hardware pop-up will appear, stating that the software for

the new device has been installed; your installation is complete.

Windows 2000

1. Turn on your computer; during Windows startup, several New Hardware

Found windows will appear, and the appropriate drivers will be installed.

Your installation is complete.

For

Windows

Support Note: High-speed USB 2.0 is supported only under Windows

2000 with Service Pack 3 installed or Windows XP with Service Pack 1

or later installed. However, USB 2.0 peripherals are backward-compatible, and

Tango 2.0 will support them at USB 1.1 speeds (12 Mb/sec. maximum) when

they are used under any other supported version of Windows.

Using FireWire and USB Devices With The Tango 2.0

Known Issues and Advice

FireWire and USB interfaces have many technological advantages over older

interfaces such as ADB, Serial, and SCSI, not the least of which is hot-plugging

capability. However, there are some limitations you should be aware of, and we

have listed some additional advice here. Refer to the peripheral manufacturers’

web sites and user’s guides for more speciﬁc information.

• Many peripherals require additional drivers and application software to

operate or have full functionality. Software should be included with the

device, or available to download from the manufacturer’s web site. Check the

peripheral’s user’s manual for information about necessary software.

• Mac Users: While USB keyboards and mice are compatible with Tango 2.0,

certain functions cannot be supported on pre-G3 machines; this is an Apple

ROM issue and not a problem with the Sonnet Tango 2.0. Because pre-G3

Macintosh computers were built before Apple added onboard USB support,

certain features, including keyboard startup, wake from sleep (by pressing a

key or moving the mouse), and others, will not work. We recommend that

you keep an ADB keyboard and mouse connected to your system to support

such functionality.

• Mac Users: When the Tango 2.0 is installed in a pre-G3 Macintosh computer,

connected FireWire drives cannot be used as the system startup (boot) drive.

• Mac Users: Always unmount a drive from the desktop (“eject” it or drag it to

the trash) before disconnecting it from its cable or the Tango 2.0 card.

• Windows Users: Always “stop”, “unplug”, or “eject” any drive connected to the

USB or FireWire ports before disconnecting it from its cable or the Tango 2.0

card.

• Disconnecting USB or FireWire peripherals (including external storage devic-

es, cameras, memory card readers, printers, etc.) while they are transferring or

receiving data, may result in damage to the ﬁle(s) being transferred or cause

your system to hang.

• Remember to connect external power supplies to the peripherals that require

them. Although many peripherals may draw power directly from the Tango

2.0 card, other devices require an external power source.

• When a high-speed USB 2.0 peripheral is connected to a USB 1.1 peripheral,

which is in turn connected directly to the Tango 2.0, the high-speed USB 2.0

peripheral will operate at USB 1.1 speeds. Keep USB 2.0 and USB 1.1 devices

connected separately.

• Should you need to connect high-speed USB 2.0 peripherals to a hub, be sure

to use a USB 2.0 hub; high-speed USB 2.0 peripherals connected to a standard

USB hub will operate at USB 1.1 speed.

• When transferring data from a digital video camera using a FireWire port on

the Tango 2.0, we do not recommend using another FireWire device at the

same time.

• Do not connect FireWire devices in a loop, nor terminate a FireWire chain;

there are no terminators or ID settings required for any FireWire device.

Inhaltsverzeichnis

Andere Sonnet PCI-Karte Handbücher

Sonnet

Sonnet TEMPO HD Bedienungsanleitung

Sonnet

Sonnet TEMPO ATA133 Bedienungsanleitung

Sonnet

Sonnet PRESTO Bedienungsanleitung

Sonnet

Sonnet Aria extreme 54 Mbps Wireless LAN Bedienungsanleitung

Sonnet

Sonnet Tempo SATA III 6Gb PCIe 2.0 Bedienungsanleitung

Sonnet

Sonnet Allegro USB3-4PM-E Bedienungsanleitung

Sonnet

Sonnet ARIA EXTREME N PCI Bedienungsanleitung

Sonnet

Sonnet M.2 Bedienungsanleitung

Sonnet

Sonnet TEMPO Trio Bedienungsanleitung

Sonnet

Sonnet TANGO 2.0 Bedienungsanleitung

Sonnet

Sonnet ALLEGRO USB 2.0 Bedienungsanleitung

Sonnet

Sonnet M.2 4x4 PCIe Card Bedienungsanleitung

Sonnet

Sonnet ALLEGRO FW800 Bedienungsanleitung

Sonnet

Sonnet TEMPO Trio Bedienungsanleitung

Sonnet

Sonnet Solo10G Bedienungsanleitung

Sonnet

Sonnet PRESTO Bedienungsanleitung

Sonnet

Sonnet ALLEGRO FW400 Bedienungsanleitung

Sonnet

Sonnet G10E-1X-E3 Bedienungsanleitung

Sonnet

Sonnet Crescendo/L2 G3 Bedienungsanleitung

Sonnet

Sonnet ALLEGRO FW400 PCIe Bedienungsanleitung

Sonnet

Sonnet ALLEGRO FW800 Bedienungsanleitung

Sonnet

Sonnet ARIA EXTREME N PCI Bedienungsanleitung

Sonnet

Sonnet ALLEGRO USB 2.0 Bedienungsanleitung

Sonnet

Sonnet Tango 3.0 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

Moxa Technologies

Moxa Technologies CP-102E Bedienungsanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung