Sony PFM-32C1 Bedienungsanleitung

INSTALLATION MANUAL

Sony Electronics Inc.

16450 West Bernardo Drive

San Diego, CA 92127

www.son

.com/

lasma

- 2 -

oSafety & precautions

oMount diagrams

oParts List

oBuilding the stand

oSecuring the plasma to the stand

oTabletop fixed installation (optional)

The floor or tabletop must be capable of supporting at least five (5) times the weight of plasma display. If not, the floor or tabletop must be

reinforced. Proper installation procedure by qualified personnel as outlined in the installations instructions must be adhered to. Failure to do

so could result in serious

ersonal in

The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions before

beginning installation. The installation instructions should be read, understood and followed to prevent personal injury or property damage.

Keep these installation instructions in an easily accessible location for future reference.

Indicates that the power plug is to be disconnected from

the power outlet.

Safety precautions must be taken at all times.

Contact Son

for an

uestions

Warning and caution in general

Do not install near heater, fireplace, direct sunlight or air conditioning or any other source of direct heat energy. Failure to do so may

result in damage to the plasma display and could cause a risk of fire.

At least two qualified people should always perform the installation work. Injury and damage can result from dropping or mishandling

the plasma display.

Contents

Safety & Precautions

WARNING: Safety precaution measures must be practiced at all times during the installation of this product. Use proper safety gear and tools for the

installations

rocedure to

revent

ersonal in

or dama

e to the

lasma dis

lasma mount.

- 3 -

(A)

12 X 22

(304 x 558)

1.00

(25.4)

20.00

(508)

20.50

(520.7)

18.25

(463.5)

PART#:

SPMTRI/C

MATERIALS USED:

12 (GA) CRS, Clear acrylic base

COLOR:

Silver

A. Back plate

B. Stand support

C. Clear base

D. Security access screws

E. (1) Cable access hole

F. Fixed tabletop mounting holes

Stand diagrams

MODEL A

PFM-32C1 .37 (9.4)

FWD32LX1,FWD32DV1 1.0 (25.4)

PFM-42B1,PFM-42V1, FWD42X1 .72 (18.2)

PFM-42LX1, FWD42DV1 1.0 (25.4)

PFM-50C1 .90 (22.8)

PFM-50DV1 1.0 (25.4)

Dimensions are in Inch and mm

- 4 -

42"

50"

Phillips screwdriver (4) M5 x 10 (mm) flat head Phillip screws (4) Clear rubber feet

(6) M5 x 30 (mm) flat head Phillip screws (2) M6 x 30 Phillips head screws (used on the 30” plasma only)

(2) M5 x 12 (mm) phillip security screws (used on 42" and 50" plasma displays only)

(2) #10 x 1-3/4" wood screws (Optional use)

Parts List

TOOLS & SUPPLY NEEDED

Building the stand

Step 1

Unpack the components from the box and set them on the floor. Invert and apply the four (4) clear rubber feet to the flat surface on the

base, locate the four mounting points on the clear base. Secure the two (2) upright supports (flat surface facing out) to the base by using

the four (6) M5 x 30 (mm) Phillip screws (supplied). CAUTION: Do not over tighten the screws.

HARDWARE

Step 2

The stand fits a 32" 42" and 50" PFM series (Sony plasma displays only). The plate is stamped with two plasma sizes. Check the size that

fits your plasma before installing. NOTE: If using a 32” plasma, the plate is not needed. Mount the plasma quick release sleeves from

the plasma to the key-holes on the uprights.

The size and arrow must always point up prior to installation, finger tighten the (4) M5 x 10 (mm) phillips flat head screws then tighten the

screws. See figure 2.

Uprights

Clear base

(6) M5 x 30

Flat head screws

(4) M5 x 10

Flat head screws

Mounting plate

- 5 -

NOTE: Two (2) security screws for

the 42" and 50" plasma displays.

Check all hardware for proper

tightness and security.

Securing the plasma to the stand

Step 3

Raise the display with the securing sleeves installed to the plasma. Slip the sleeves through the four (4) keyholes on the back plate and

drop it down slowly, make sure all of the four (4) sleeves are in the keyhole slot before letting go of the plasma. On the 42" and 50" two (2)

M5 x 12 Phillip screws (security screws) can be used for additional security. See figure 3.

NOTE: If using a 32” plasma, secure it with the two (2) M6 x 30 Phillip screws supplied.

NOTE: Security screws for the 32”

plasma displays. Check all hardware

for proper tightness and security.

M5 x 12 phillips

screws

M6 x 30 phillips

screws

- 6 -

(Optional) fixed installation

Step 1

Invert the stand and locate the two (2) mounting points on the bottom of the stand for (optional) fixed tabletop installation. Measure the

distance between center to center of these two (2) holes and mark the table. See figure 4.

NOTE: This diagram shows

the bottom of the stand.

Step 2

OPTIONAL TABLE MOUNTING

If securing to a wood table, mark the table and drill properly. Secure the stand with the two (2) #10 x 1-1/4" wood screws (supplied).

NOTE: Longer or shorter wood screws and or mounting hardware depending on your installation environment are (commercially

available). See figure 5.

NOTE: Check all hardware for proper

tightness and security.

Wood screw

access holes

Wood screw

access

#10 x 1-1/4”

wood screws

Flat wood surface

Andere Handbücher für PFM-32C1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sony Rack & Stand Handbücher

Sony

Sony VCT-HM1 Bedienungsanleitung

Sony

Sony RHT-G2000 - Home Theater Built-in Sound Rack... Bedienungsanleitung

Sony

Sony WS-FV10 Bedienungsanleitung

Sony

Sony WB-PW1 Bedienungsanleitung

Sony

Sony SU-WL11 Bedienungsanleitung

Sony

Sony RMM-1100 Bedienungsanleitung

Sony

Sony Walkman BCR-NWA800 Bedienungsanleitung

Sony

Sony RHT-G550 Bedienungsanleitung

Sony

Sony BKM-30E20 Bedienungsanleitung

Sony

Sony RMM-ES701 Bedienungsanleitung

Sony

Sony SU-SX10 Bedienungsanleitung

Sony

Sony KV-36FS100 Instructions: TV stand (primary... Bedienungsanleitung

Sony

Sony Bravia Theatre Sync RHT-G800 Gebrauchs- und Wartungshandbuch

Sony

Sony SU-W110 Bedienungsanleitung

Sony

Sony SU-PF1 Bedienungsanleitung

Sony

Sony DCZ-50P Bedienungsanleitung

Sony

Sony SURS51U - Stand For Rear Projection TV Bedienungsanleitung

Sony

Sony SU-FL61 Bedienungsanleitung

Sony

Sony SU-WL500 Instructions (SU-WL500 Wall-Mount... Bedienungsanleitung

Sony

Sony KDL-32EX301 - 32" Class Bravia Ex301 Hdtv Betriebsanleitung

Sony

Sony SU-32FS2 - TV Stand For Bedienungsanleitung

Sony

Sony SU-HR3432CH Bedienungsanleitung

Sony

Sony SU-WL450 Service-Handbuch

Sony

Sony SU-46NX1 Gebrauchs- und Wartungshandbuch

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung