Soundcore Liberty Air 2 Pro Bedienungsanleitung

Liberty Air 2 Pro

USER MANUAL

English 01

Čeština 08

Dansk 15

Deutsch 22

ελληνικά 29

Español 36

Suomi 43

Français 50

Magyar 57

Italiano 64

Nederlands 71

Norsk 78

Język polski 85

Português 92

Portugues do Brasil 99

Pусский 106

Slovenský Jazyk 113

Slovenski Jezik 120

Svenska 127

Türkçe 134

日本語141

한국어148

简体中文155

繁體中文162

 169

 

176

01 EN

Charging

• Remove the protective lm from the earbuds before the rst use.

• Fully dry off the earbuds and the USB port before charging.

• Use a certied USB-C charging cable and charger to prevent any damage.

• Fully charge both the earbuds and the charging case before the rst use.

1. Place the earbuds in the charging case and close it.

The rst and the third LED indicators on the charging case will ash twice. This

conrms that the earbuds are being charged.

2. Connect the charging case to the power supply by using a USB-C charging cable.

Alternatively, position the charging case at the center of your wireless charger for

wireless charging.

The LED indicators on the c harging case indicate the charging status.

< 30%

30% - 70%

> 70%

100%

3. To check the battery level of the charging case, open it to activate the LED

indicator.

10% - 30%

< 10%

30% - 70%

> 70%

EN 02

Soundcore App

Download the Soundcore app to enhance your experience.

HearID: HearID maps your personal hearing sensitivity at multiple frequencies and

analyzes the results. It traces the EQ settings and creates a personalized sound

prole for you.

User interface customization: In stereo mode, all of the controls (e.g. adjust volume,

control playback, activate Siri) can be customized in the app.

EQ settings: There are more than 20 EQ settings you can choose from in the app to

optimize your experience while enjoying different music genres.

Noise cancellation: Choose an active noise cancellation mode to reduce ambient

noise according to your surroundings.

• Transport: Targets low-end frequencies like engine and road noise for peaceful

journeys and commutes.

• Outdoor: Reduces ambient sounds in cities for less distractions.

• Indoor: Reduces voices and mid-frequency noise from coffee shops and other inside

spaces.

Custom ANC: Adjust the noise cancellation level to suit you in the app.

Transparency mode: Stay aware of your surroundings by allowing ambient sounds

in.

• Fully Transparent: Hear all ambient sounds.

• Vocal Mode: Voices stand out more clearly from other ambient sounds.

Earbuds rmware update: You will be informed once the new version of rmware

is detected when you connect the earbuds with the app. Ensure the earbuds are

placed in the charging case and the case remains open until the rmware upgrade

is completed. During the upgrade, ensure the earbuds are being charged and avoid

any operation.

03 EN

Wearing

1. Choose the Liquid Silicone EarTips that t your ears best.

2. Insert the earbuds into the inner canal of your ears and turn gently until you nd

the most comfortable and secure position.

XL MM+

XS XXS XXXSS

LL+

Your earbuds come with multiple pairs of EarTips, among which Medium-sized are

pre-installed.

Powering On/Off

Open the charging case, the earbuds will automatically power on.

The LED indicator on earbuds will light up white for 1 second.

To power off, place the earbuds in the charging case and it.

1OFF 2

When you’re wearing the earbuds, they will not power off until out of battery. When

you remove the earbuds, they will automatically power off after 30 minutes if no

device is connected.

EN 04

Bluetooth Pairing

1. Open the charging case, the earbuds will automatically enter the Bluetooth

pairing mode.

The LED indicator on one earbud will flash quickly and on another earbud

breathe slowly.

2. Select “Soundcore Liberty Air 2 Pro” on your device’s Bluetooth list to connect.

When successfully connected, the LED indicator on earbuds will light up white

for 1 second.

1 2

Soundcore

Liberty Air 2 Pro

Soundcore

Liberty Air 2 Pro

• Each time you power on your Soundcore earbuds, they will automatically

connect to your last successfully connected device if available within the

Bluetooth range.

• Mono mode: When Bluetooth connected, you can use either one of the earbuds

only by placing the other one into the charging case and closing it.

• When powered on and connected, if either one of the earbuds is out of battery

and powered off, you can keep using the other one.

• When you are on a call, place either one of the earbuds into the charging case

and close it, the microphone in the other earbud will be activated.

Pairing with another device

1. Place the earbuds in the charging case and leave the case open. Press and hold

the button on the case for 3 seconds until the earbud LED indicators ash white to

enter the pairing mode.

2. Select “Soundcore Liberty Air 2 Pro” on your device’s Bluetooth list to connect.

05 EN

Soundcore

Liberty Air 2 Pro

Soundcore

Liberty Air 2 Pro

3”

Controls

Play/Pause Tap twice (R)

Next track Tap twice (L)

Answer a call

Tap twice (L/R)

Answer a second incoming call and put the

current call on hold

End/Reject a call Press and hold for 2 seconds (L/

Switch between a call on hold and an active call

Switch ambient sound modes

(Noise Cancellation/Normal)

Press and hold for 2 seconds (L/

EN 06

Mono mode

Play/Pause Tap twice

Answer a call

End/Reject a call Press and hold for 2 seconds

Activate Siri or other voice assistant software

• All of the controls in stereo mode can be customized in the Soundcore app. In

mono mode, controls cannot be customized in the app.

• Music playback will auto-pause when removing the earbuds, wear them again to

resume.

• Adjust the volume level via the connected device or in the Soundcore app.

• In stereo mode, noise cancellation mode is set by default. Each time you power

on and connect, or switch to the stereo mode from mono mode, your earbuds

will restore the last setting.

• Noise cancellation or transparency mode is unavailable in mono mode.

Reset

You might need to reset your earbuds if you experience any connectivity problems

or function issues.

1. Place the earbuds in the charging case and leave the case open.

2. Press and hold the button on the case for 10 seconds until the earbud LED

indicators ash red 3 times and then turn white.

3. Wait until the LED indicator on one of the earbuds flashes fast while the other

breathes slowly. This conrms that the reset was successful and your earbuds can be

connected normally.

2 3

10”

The following two examples indicate the reset has not been successful and the

previous steps should be repeated.

07 EN

• If only one earbud LED indicator ashes;

• If both earbud LED indicators ash quickly.

Specifications

Specications are subject to change without notice.

Input 5 V 0.5 A

Rated output power 5 mW @ 1% THD

Battery capacity 55 mA x 2 (earbuds);

500 mA (charging case)

Charging time 2 hours

15-minute charge = 3-hour playtime

Playtime

(varies by volume level and content)

Up to 7 hours

(Total 26 hours with the charging case)

Playtime

(with ANC mode turned on)

Up to 6 hours

(Total 21 hours with the charging case)

Playtime

(with transparency mode turned on)

Up to 6.5 hours

(Total 23 hours with the charging case)

Talk time Up to 4 hours

(Total 14 hours with the charging case)

Driver size 11 mm

Frequency response 20 Hz - 20 kHz

Impedance 16 Ω

Waterproof level

(The waterproof level may reduce

over time as a result of daily use)

IPX4

(The earbuds are not desig ned for swimming,

showering, or exposure to pool or ocean

water. Do not use in a sauna or steam room.

The charging case is not waterproof. )

Bluetooth version V 5.0

Bluetooth range 10 m / 33 ft

08 CS

Nabíjení

• Před prvním použitím odstraňte ze sluchátek ochrannou fólii.

• Před nabíjením sluchátka a port USB úplně vysušte.

• Použijte pouze certikovaný nabíjecí kabel USB-C a nabíječku, abyste zabránili

poškození.

• Před prvním použitím sluchátka i nabíjecí pouzdro úplně dobijte.

1. Sluchátka vložte do nabíjecího pouzdra a zavřete ho.

První a třetí LED kontrolka na nabíjecím pouzdře dvakrát zabliká. To potvrzuje, že

se sluchátka nabíjí.

2. Nabíjecí pouzdro pomocí nabíjecího kabelu USB-C připojte do elektřiny.Pokud

používáte bezdrátové nabíjení, můžete místo toho nabíjecí pouzdro umístit do

středu bezdrátové nabíječky.

LED kontrolky na nabíjecím pouzdře zobrazují stav nabíjení.

< 30%

30% - 70%

> 70%

100%

3. Chcete-li zjistit úroveň nabití baterie nabíjecího pouzdra, pouzdro otevřete, abyste

aktivovali LED kontrolku.

10% - 30%

< 10%

30% - 70%

> 70%

Andere Handbücher für Liberty Air 2 Pro

Inhaltsverzeichnis

Andere Soundcore Kopfhörer Handbücher

Soundcore

Soundcore Vortex Bedienungsanleitung

Soundcore

Soundcore Sleep A10 Bedienungsanleitung

Soundcore

Soundcore Space A40 Bedienungsanleitung

Soundcore

Soundcore Space NC A3021 Bedienungsanleitung

Soundcore

Soundcore Life Note 3 Bedienungsanleitung

Soundcore

Soundcore Space Q45 Bedienungsanleitung

Soundcore

Soundcore Liberty Air 2 Bedienungsanleitung

Soundcore

Soundcore Liberty Neo Bedienungsanleitung

Soundcore

Soundcore Life Q10 Bedienungsanleitung

Soundcore

Soundcore Liberty Air Bedienungsanleitung

Soundcore

Soundcore Liberty Air 2 Bedienungsanleitung

Soundcore

Soundcore Life Note C Bedienungsanleitung

Soundcore

Soundcore Space Q45 Bedienungsanleitung

Soundcore

Soundcore Spirit X2 Bedienungsanleitung

Soundcore

Soundcore Life Note Bedienungsanleitung

Soundcore

Soundcore Liberty Air 2 Pro Bedienungsanleitung

Soundcore

Soundcore Soundcore Life P2 Bedienungsanleitung

Soundcore

Soundcore Life Q35 Bedienungsanleitung

Soundcore

Soundcore Space Q45 Bedienungsanleitung

Soundcore

Soundcore Life Q30 Bedienungsanleitung

Soundcore

Soundcore Liberty 2 Bedienungsanleitung

Soundcore

Soundcore Life Q20 Bedienungsanleitung

Soundcore

Soundcore A3951 Bedienungsanleitung

Soundcore

Soundcore Life Note Bedienungsanleitung

Beliebte Kopfhörer Handbücher anderer Marken

Sony

Sony MDR-NC8 Bedienungsanleitung

AUSounds

AUSounds AU-Stream Bedienungsanleitung

ENERGY SISTEM

ENERGY SISTEM Style 7 Bedienungsanleitung

Philips

Philips SHE3622 Bedienungsanleitung

Insignia

Insignia NS-CAHBTSPORT Bedienungsanleitung

Movie Vision

Movie Vision HP-400 Bedienungsanleitung

MobiFren

MobiFren SM Pro Bedienungsanleitung

Motorola solutions

Motorola solutions PMLN8120 Bedienungsanleitung

Jaybird

Jaybird freedom Installationsanleitung

Sony

Sony MDR-ED12LP Bedienungsanleitung

HiFuture

HiFuture Tidy Buds Pro Bedienungsanleitung

Creative

Creative CB2530 Bedienungsanleitung

Renkforce

Renkforce RF FTVK-100 Bedienungsanleitung

Philips

Philips SHQ3000 Bedienungsanleitung

Sennheiser

Sennheiser 500371 Bedienungsanleitung

Califone

Califone 2924AV Bedienungsanleitung

Philips

Philips EARGEAR HE205 Series Bedienungsanleitung

Technics

Technics EAH-AZ80 Bedienungsanleitung