Sper scientific 850007 Bedienungsanleitung

Visible Light

SD Card Datalogger

850007

Instruction Maual

2 3

Visible Light SD Card Datalogger - 850007

Printed in the USA

The contents of this manual may not be reproduced or transmitted in any

form or by any means electronic, mechanical, or other means that do not

yet exist or may be developed, including photocopying, recording, or any

information storage and retrieval system without the express permission

from Sper Scientic.

INTRODUCTION ..........................................3

FEATURES ..............................................3

MATERIALS SUPPLIED ....................................3

POWER SUPPLY ..........................................4

METER COMPONENTS & KEYPAD...........................4

SETUP ..................................................5

MEASUREMENT PROCEDURES.............................6

DATALOGGER ...........................................10

BATTERY REPLACEMENT .................................12

TROUBLESHOOTING .....................................12

SPECIFICATIONS ........................................13

WARRANTY.............................................16

TABLE OF CONTENTS

INTRODUCTION

The Sper Scientic Visible Light SD Card Datalogger (Model 850007) is an

intelligent meter that reads light in Lux or Foot Candles and functions as a

Type K/J thermocouple thermometer.

This meter features a real time SD memory card datalogger. Standard,

portable SD memory cards provide unlimited data storage and upload

pre-formatted data directly to Excel, eliminating the need for cables or

software. Each data set includes light measurement, time and date.

FEATURES

• Functions as a light meter

and Type K/J thermometer

• Three ranges for light

measurement

• Auto range for light measurement

• Lux or Foot Candles

unit selection

• SD memory card datalogger

• Manual datalogger option

• Photo sensor spectrum

meets CIE

• Zero adjustment

• Highly accurate

microcomputer circuit

• Direct upload of data to Excel

• Detachable probe for measuring

exibility

• Internal clock and calendar

• Touch-tone

• Tripod mounting screw

• Built-in tabletop stand

• Maximum and minimum

• Hold function

• Auto-power-o󰀨

• Low battery indicator

• Backlight

MATERIALS SUPPLIED

• Meter

• Sensor

• SD Card

• 6 AA Batteries

• Instruction Manual

• Soft Carrying Case

4 5

POWER SUPPLY

This meter can be powered by six AA (1.5 V, UM3) batteries or an

optional 9 Volt DC adapter. See battery replacement instructions.

Plug the adaptor into the power port labelled “DC 9V,” located on the

side of the meter.

Note…

When using the adapter, the meter will remain permanently

ON and the POWER button will be disabled.

METER COMPONENTS & KEYPAD

1 2

612

1. Type K/J Thermocouple Socket

2. Light Sensor Input Socket

3. LCD Screen

4. Function/Hold/Next Button

5. Record/Enter Button

6. Logger/Sampling Check/Zero/

▲ Button

7. Reset

8. CD 9V Adapter Input Socket

9. SD Card Socket

10. Set/Time Check/▲ Button

11. Power/Esc Button

12. Light Sensor

(sensor cover not pictured)

13. Sensor Handle

SETUP MODE

The advanced Setup Mode allows you to customize the

following meter preferences and defaults:

• Real Time Clock

• Decimal Type

• Auto Power O󰀨

• Touch-Tone

• Thermometer Type K/J

• Temperature Units

• Sampling Time

• SD Memory Card Format

Note…

The setup functions can be performed under any parameter but not

while utilizing the datalogger function. Once selections are saved, the

meter will default to the selected preferences. Once a selection is saved,

the meter automatically advances to the next setup function (i.e., after

setting the real time clock, the meter will automatically enter the decimal

type setup function).

1. Press POWER to turn the meter on.

2. Press SET for 2 seconds or longer to enter Setup Mode.

3. Press NEXT to cycle through the setup functions.

Note…

Press ESC to exit Setup Mode. The meter will return to Normal Mode.

Real Time Clock

1. Enter the clock function from Setup Mode (as described above).

“dAtE” appears on the LCD.

2. Press ENTER. The year will appear on the LCD.

3. Press ▲ or ▼ to adjust the value. Press ENTER to save the value.

4. Repeat Step 3 to adjust the month, date, hour, minute and second.

Note…

This procedure adjusts the meter’s internal clock. The internal clock will

function when the meter is turned o󰀨 but only when the batteries have

adequate power (not with low battery power.)

Decimal Type

Although the decimal is commonly expressed as the “.” symbol (i.e., 20.6

or 1000.53), some (European) countries use a “,” symbol to represent the

decimal (i.e., 20,6 or 1000,53). The meter defaults to the period symbol.

To adjust:

1. Enter the decimal type function from Setup Mode (see page 5).

“dEC” appears on the LCD.

2. Press ▲ or ▼ to select Basic (.) or Euro (,). Press ENTER to

save the selection.

Auto Power O󰀨

The meter automatically turns o󰀨 after 10 minutes of inactivity,

however this function can be disabled.

1. Enter the auto power o󰀨 function from Setup Mode (see page 5).

“PoFF” appears on the LCD.

2. Press ▲ or ▼ to select yes (auto power o󰀨 enabled) or no

(auto power o󰀨 disabled). Press ENTER to save the selection.

Touch-Tone

1. Enter the touch-tone function from Setup Mode (see page 5).

“bEEP” appears on the LCD.

2. Press ▲ or ▼ to select yes (touch-tone enabled) or no

(touch-tone disabled). Press ENTER to save the selection

Thermometer Type K/J

1. Enter the thermometer type function from Setup Mode

(see page 5). “tYPE” appears on the LCD.

2. Press ▲ or ▼ to select K or J. Press ENTER to save

the selection.

Temperature Units

1. Enter the temperature units function from Setup Mode

(see page 5). “t-CF” appears on the LCD.

2. Press ▲ or ▼ to select C (degrees Celsius) or F (degrees Fahrenheit).

Press ENTER to save the selection.

Sampling Time

The sampling time is the time allotted between successive

measurements. To adjust the sampling time (in seconds):

1. Enter the sampling time function from Setup Mode (see page 5).

“SP-t” appears on the LCD.

2. Press ▲ or ▼ to adjust the value (0, 1, 2, 5, 10, 30, 60, 120, 300,

600, 800, 1800, 3600 seconds). Press ENTER to save the value.

SD Memory Card Format

Enabling this function will format the SD memory card to work

specically with your meter. Formatting the SD card will erase any

previous memory on the card. New SD cards should be formatted

to work with your meter.

1. Enter the SD memory card format function from Setup Mode

(see page 5). “Sd F” appears on the LCD.

2. Press ▲ or ▼ to select yes (format the SD memory card) or no

(do not format the SD memory card). Press ENTER to conrm your

selection. If selecting yes, “yES Enter” will appear on the LCD,

press ENTER again and the meter will format the SD card.

MEASUREMENT PROCEDURES

Turning the Unit On/O󰀨

Press POWER to turn the meter on.

Press and hold POWER for 2 seconds to turn the meter o󰀨.

Selecting the Function

1. Press and hold FUNC to cycle through the options listed below.

Release FUNC when you reach the desired function.

Light Meter: “LIgHt” appears on the LCD.

Type K/J thermometer: “tP” appears on the LCD.

Note…

The meter will default to the last function setting used when it is

turned o󰀨 and on again.

Light Meter

1. Press POWER to turn the meter on.

2. Plug the probe plug into the probe input socket.

3. Remove the sensor cover from the light sensor.

4. Press and hold FUNC to cycle through the options until “LIgHt”

appears on the LCD. Release the FUNC button.

5. While holding the sensor handle, point the light sensor directly toward

(facing) the light source. The light measurement will appear on the LCD.

Note…

This meter measures light in Lux or Foot Candles (Ft-cd). To change the

light unit, press and hold REC ENTER. Release REC ENTER when the

desired unit appears on the LCD.

Zero Adjustment

During light measurement, if the display does not show a value of

0 when the sensor cover is placed on the light sensor, zero adjustment

is needed:

1. With the sensor cover on, press ZERO for longer than 3 seconds.

A value of 0 will appear on the LCD.

2. Remove the sensor cover to resume normal measurement.

Type K/J Thermometer

1. Press POWER to turn the meter on.

2. Press and hold FUNC to cycle through the options until “tP”

appears on the LCD. Release the FUNC button.

3. Plug a thermocouple temperature probe (type K or J) into the

thermometer socket. The temperature measurement will appear on

the LCD along with “K” or “J” to indicate the thermocouple type.

Note…

When using the meter for the rst time, the meter will default to K

type thermocouple. See page 6 for instructions on changing the

thermocouple type.

Hold Function

1. When measuring any parameter, press HOLD to freeze the reading

on the display. “HOLD” will appear on the LCD.

2. Press HOLD again to release the hold function. “HOLD” will

disappear from the LCD.

Maximum and Minimum

To record maximum and minimum readings:

1. When measuring any parameter, press REC to begin recording the

maximum and minimum values. “REC” appears on the LCD.

Press

REC

. The maximum value and “REC MAX” will appear on the LCD.

3. Press REC. The minimum value and “REC MIN” will appear on the LCD.

4. To delete the maximum or minimum value, press HOLD. “REC”

appears on the LCD and the meter will begin recording the maximum

and minimum values again.

5. To exit the min/max function, press and hold REC for 2 seconds.

The meter will return to Normal Mode.

Note…

The meter cannot be turned o󰀨 from the memory record function.

Exit the function, then press and hold POWER to turn the meter o󰀨.

Backlight

The backlight turns on automatically when the meter is turned on.

Press  to turn the backlight o󰀨.

Press  to turn the backlight on.

View Real Time Clock

To view the time function during normal measurement (not during

datalogging):

1. Press TIME CHECK. The time information (Year, Month/Date,

Hour/Minute) will appear on the lower display of the LCD.

View Sampling Time

To view the sampling time function during normal measurement

(not during datalogging):

1. Press SAMPLING CHECK. The sampling time (in seconds)

will appear on the lower display of the LCD.

10 11

DATALOGGER

Preparing the Datalogger

1. Insert the SD card into the SD card socket on the bottom of the meter,

ensuring that the front of the SD card faces the back of the meter.

2. Format the SD card as needed (see page 7).

3. Set the clock if using the meter for the rst time (see page 7).

4. Set the decimal type if using the meter for the rst time (see page 6).

Auto Datalogging

1. Set the sampling time to ≥ 1 second. Refer to page 7.

2. Press REC. “REC will appear on the LCD.

3. Press LOGGER. “REC” will ash on the LCD and the alarm will sound

while the measurement data and time information are saved to memory.

4. To pause datalogging, press LOGGER. The meter will temporarily

stop recording and “REC” will stop ashing on the LCD. Press

LOGGER again to resume datalogging. “REC” will ash on the LCD.

5. To nish datalogging, pause the datalogger. Press REC for 2 secs. or

longer. “REC” will disappear from the LCD to indicate that datalogging

has ended.

Note…

To enable/disable the touch-tone feature, see page 6.

Manual Datalogging

1. Set the sampling time to 0 seconds. Refer to page 7.

2. Press REC. “REC will appear on the LCD.

3. Press LOGGER. “REC” will ash on the LCD and the alarm will

sound while the measurement data and time information are saved to

memory. The position (location) number will appear on the bottom of

the LCD and will also be recorded on the SD card.

Note…

To enable/disable the touch-tone feature, see page 15. To change the

position number, press ▼. The position number will ash on the LCD.

Press ▲ or ▼ to set the position number (from 1 to 99). To indicate the

position location, P x (x = 1 to 99) will appear on the lower display. After

selecting the position number, press ENTER to conrm.

4. To nish datalogging, press REC for longer than 2 seconds. “REC”

will disappear from the LCD to indicate that datalogging has ended.

Inhaltsverzeichnis

Andere Sper scientific Messgerät Handbücher

Sper scientific

Sper scientific 840064 Bedienungsanleitung

Sper scientific

Sper scientific WBGT Bedienungsanleitung

Sper scientific

Sper scientific 900019 Bedienungsanleitung

Sper scientific

Sper scientific 840020 Bedienungsanleitung

Sper scientific

Sper scientific 840062 Bedienungsanleitung

Sper scientific

Sper scientific 800111 Bedienungsanleitung

Sper scientific

Sper scientific 850070 Bedienungsanleitung

Sper scientific

Sper scientific 850081DOK Bedienungsanleitung

Sper scientific

Sper scientific 850004 Bedienungsanleitung

Sper scientific

Sper scientific 840012 Bedienungsanleitung

Sper scientific

Sper scientific 840065 Bedienungsanleitung

Sper scientific

Sper scientific 800100 Bedienungsanleitung

Sper scientific

Sper scientific 840021 Bedienungsanleitung

Sper scientific

Sper scientific 840020 Bedienungsanleitung

Sper scientific

Sper scientific 840087 Bedienungsanleitung

Sper scientific

Sper scientific 850024 Bedienungsanleitung

Sper scientific

Sper scientific 900030 Bedienungsanleitung

Sper scientific

Sper scientific 840021 Bedienungsanleitung

Sper scientific

Sper scientific 840003 Bedienungsanleitung

Sper scientific

Sper scientific 850081 Bedienungsanleitung

Sper scientific

Sper scientific 800046 Bedienungsanleitung

Sper scientific

Sper scientific 300056 Bedienungsanleitung

Sper scientific

Sper scientific CL-2006 Bedienungsanleitung

Sper scientific

Sper scientific 850013 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung