Sper scientific 840062 Bedienungsanleitung

Torque Meter

840062

Instruction Manual

Torque Meter - 840062

Printed in the USA

The contents of this manual may not be reproduced or transmitted

in any form or by any means electronic, mechanical, or other

means that do not yet exist or may be developed, including

photocopying, recording, or any information storage and retrieval

system without the express permission from Sper Scientic.

INTRODUCTION .....................................3

METER DESCRIPTION ................................3

OPERATING INSTRUCTIONS

Measurement Procedures .............................4

Automatic Shut O󰀨...................................5

Battery Replacement .................................5

Software Download ..................................5

RS232 PC Serial Interface ............................6

SPECIFICATIONS ....................................7

WARRANTY.........................................8

TABLE OF CONTENTS

INTRODUCTION

This portable meter is used for bolt torquing, torque wrench

calibration, switch or contact closure measurement and other

industrial, QC, and materials testing applications. Features

three units of measure as well as hold, peak, min-max, fast/slow

sampling, hi/low resolution auto power o󰀨 and an RS232

computer interface.

METER DESCRIPTION

17 16 15

TORQUE METER

1. LCD Display 7. RESOLUTION Button 13. RS232 Output

2. POWER Button 8. SENSOR TYPE Button 14. Sensor Cable Plug

3. HOLD Button 9. ZERO Button 15. Torque Sensor Body

4. MAX/MIN Button 10. FAST/SLOW Button 16. Gear

5. UNIT Button 11. Battery Compartment 17. Cramp

6. PEAK Button 12. Sensor Input Socket 18. Pinion

OPERATING INSTRUCTIONS

Measurement Procedures

• Plug the SENSOR CABLE PLUG into the SENSOR

INPUT SOCKET.

• Turn on the meter by pressing the POWER button.

• Press the SENSOR TYPE button to check that the meter’s

sensor type matches the external torque sensor. (ie: the LCD

displays 15Kg cm.)

• Press the UNIT button to select the unit of measure: Kg cm, LB

inch or Newton cm.

• Press the RESOLUTION button to select High or Low resolution.

Unit of

Measure

Max Range High Res. Low Res. Accuracy

Kg cm 15 0.01 0.1 ±1.5% + 5d

Lb in 12.99 0.01 0.1

Newton cm 147.1 0.1 1

• Press the FAST/SLOW button to select the sampling time. “F” is

displayed for fast, “S” is displayed for slow.

• Connect the CRAMP to the object to be measured. Use the

PINION to lock the GEAR.

• Before making your measurement, the LCD should display “0.”

If not, use the ZERO button to tare the unit.

• Apply the torque force. The LCD will indicate the measured value.

• Press the PEAK button to display and hold the peak value. The

sampling time defaults to FAST and “F” will be displayed.

• During the measurement procedure, press the HOLD button to

freeze the current measured value. The LCD will display the word:

“HOLD.” Press the HOLD button again to exit this function.

• Recording the Maximum and Minimum Readings

• Press the MAX/MIN button once. “REC” appears on the LCD.

• Press the MAX/MIN button again. “REC Max” and the

maximum measurement appear on the LCD.

• Press the MAX/MIN button again. “REC Min” and the minimum

measurement appear on the LCD.

• To exit the this function, press and hold the MAX/MIN button for at

least 2 seconds, until the display reverts to the current reading.

Automatic Shut-o󰀨

Your meter has an automatic shut o󰀨 function in order to prolong

battery life. After approximately 10 minutes without activity (no

buttons pushed), the meter will automatically shut o󰀨. To disable

this feature, press the MAX/MIN button once during measurement.

“REC” will be displayed.

Battery Replacement

Replace the battery when the low battery icon is displayed in

the left corner of LCD. In-spec measurements may be made for

several hours after the low battery indicator appears. Slide the

battery cover away from the instrument, remove the

battery and replace with a 9V battery (alkaline or heavy

duty type). Close the battery cover.

Software Download

With technology upgrading, some computers no longer have

a disc drive for you to install the software that comes with your

meter. You can download the software that came with your meter

directly. Go to the www.sperdirect.com/software.htm and nd

your meter or search for you meter (840062) and download from

product page.

Note...

Some software may not be directly available to download due to

it must be purchased. If you nd that the software you need is not

available, please contact our Customer Support at 480.948.4448

or email info@sperscientic.com for further assistance.

RS232 PC Serial Interface

The unit features an RS232 Output (2-2) via a 3.5 mm terminal.

The output is a 16 digit data stream which can be adapted to the

user’s specic application. Optional RS232 Cable 840055, or an

RS232 lead with the following connection is required to link the

instrument with the computer:

Meter (3.5 mm jack plug) PC (9W ‘D” Connector)

Cent er Pin ............................................. Pin 2

Ground/shield ........................................ Pin 5

RS232 Settings:

• Baud Rate 9600

• No parity

• 8 Data bits

• 1 Stop bit

The 16 digits data stream will be displayed in the following format:

D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0

Each digit indicates the following status:

D0 End Word

D1 to D8 Upper display reading, D1 = LSD, D8 = MSD

D9 Decimal point (DP), position

0 = No DP, 1 = 1 DP, 2 = 2 DP, 3 = 3 DP

D10 Polarity for the Display

0 = Positive (+)

1 = Negative (-)

D11 & D12 Anunuciator for upper display

01 = °C, 02 = °F, 08 = m/s, 09 = knot, 10 =Km/h,

11 = ft/min, 12 = mph

D13 Upper display data = 1, Lower display data =2

D14 4

D15 Start word = 02

SPECIFICATIONS

Display 2.4" x 1.3" (61 x 34 mm)

6" (15 mm) digit size

Unit of Measure Kg - cm, LB - inch and Newton - cm

Operating Temperature 32 to 122°F (0° to 50°C)

Operating Humidity Less than 80%

Power Supply Alkaline or heavy duty type DC 9V battery

Power Consumption Approximately DC 12 mA

Weight Meter ½ lbs (225 g), Probe 1½ lbs (665 g)

Dimension Meter 7"x 3"x 1½" (180 x 75 x 35 mm)

Probe 2"x 6¼" (48 x 160 mm)

Included Accessories Hard carrying case, instruction manual,

15 kg/cm torque probe with a 4½′

(140 mm) cable, pinion, and 9V battery

OPTIONAL ACCESSORIES

840055 - RS232 Cable

840090 - Water Resistant Instrument Pouch

840094 - USB Converter

850080 - Intelligent Software

WARRANTY

Sper Scientic warrants this product against defects in materials

and workmanship for a period of one (1) years from the date

of purchase, and agrees to repair or replace any defective unit

without charge. If your model has since been discontinued, an

equivalent Sper Scientic product will be substituted if available.

This warranty does not cover probes, batteries, battery leakage, or

damage resulting from accident, tampering, misuse, or abuse of the

product. Opening the meter to expose its electronics will break the

waterproof seal and void the warranty.

To obtain warranty service, ship the unit postage prepaid to:

SPER SCIENTIFIC LTD.

8281 East Evans Road, Suite #103

Scottsdale, AZ 85260

The defective unit must be accompanied by a description of the

problem and your return address. Register your product online at

www.sperwarranty.com within 10 days of purchase.

Revised 7/25/2017

Inhaltsverzeichnis

Andere Sper scientific Messgerät Handbücher

Sper scientific

Sper scientific AquaShock Bluetooth pH Kit 850057K Bedienungsanleitung

Sper scientific

Sper scientific 850011 Bedienungsanleitung

Sper scientific

Sper scientific 850068 Bedienungsanleitung

Sper scientific

Sper scientific 860041 Bedienungsanleitung

Sper scientific

Sper scientific 840020 Bedienungsanleitung

Sper scientific

Sper scientific 850050 Bedienungsanleitung

Sper scientific

Sper scientific 840064 Bedienungsanleitung

Sper scientific

Sper scientific 850081 Bedienungsanleitung

Sper scientific

Sper scientific 840063 Bedienungsanleitung

Sper scientific

Sper scientific 850039 Bedienungsanleitung

Sper scientific

Sper scientific 840021 Bedienungsanleitung

Sper scientific

Sper scientific 850007 Bedienungsanleitung

Sper scientific

Sper scientific 850003 Bedienungsanleitung

Sper scientific

Sper scientific 800052 Bedienungsanleitung

Sper scientific

Sper scientific 860045 Bedienungsanleitung

Sper scientific

Sper scientific 850045 Bedienungsanleitung

Sper scientific

Sper scientific 800020 Bedienungsanleitung

Sper scientific

Sper scientific 850068 Bedienungsanleitung

Sper scientific

Sper scientific 840020 Bedienungsanleitung

Sper scientific

Sper scientific 860043 Bedienungsanleitung

Sper scientific

Sper scientific 840003 Bedienungsanleitung

Sper scientific

Sper scientific 850051 Bedienungsanleitung

Sper scientific

Sper scientific 840007 Bedienungsanleitung

Sper scientific

Sper scientific 850004 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung