StarTech.com S354UFER Bedienungsanleitung
External Multi Bay Hard
Drive Enclosure
3.5” 4 Drive eSATA USB FireWire
External Multi Bay Hard Drive
Enclosure with RAID
S354UFER
Instruction Manual
Manual Revision:08/05/2010
For the most up-to-date information, please visit www.startech.com
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an
endorsement of the product(s) to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgement elsewhere in the body of
this document, StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this
manual and related documents are the property of their respective holders.
i
Table of Contents
Introduction..................................................................... 1
Packaging Contents.....................................................................1
System Requirements .................................................................1
Installation....................................................................... 2
Hardware Installation...................................................................4
Driver Installation.........................................................................5
How to Use ...................................................................... 6
Hard Drive DIP Switch.................................................................6
RAID Mode..................................................................................6
Drive Status Indicators ................................................................8
eSATA/USB/FireWire Connectivity ..............................................8
Fan Speed Control ......................................................................9
Troubleshooting .............................................................. 9
Specifications.................................................................. 10
Technical Support........................................................... 12
Warranty Information...................................................... 12
1
Introduction
StarTech.com’s S354UFER External Multi Bay Enclosure is a high-
performance 4-drive SATA enclosure that connects to host systems
through eSATA or USB or FireWire.
Packaging Contents
• 1 x S354UFER enclosure
• 1 x Screw driver and screw kit
• 4 x Hard Drive Handles
• 1 x Univeral Power Adapter with 3 Power Cords (NA/UK/EU)
• 1 x eSATA cable
• 1 x USB cable
• 1 x 6-pin FireWire cable
• 1 x 9-pin FireWire cable
• 1 x Instruction Manual
System Requirements
• USB or eSATA* or FireWire enabled computer system
• Microsoft Windows®2000/XP/Server 2003/Vista,
Mac OS®10.3 and later or Linux®
*If connecting the enclosure to a host computer using the eSATA
port, please note that in order to use some of the RAID modes of
the enclosure, the eSATA port on the host computer system must
provide Port Multiplier support. If the eSATA port does not offer Port
Multiplier support, only one of the installed drives will be accessible.
2
Installation
Front View
Rear View
USB port
eSATA port
DIP Switch
Confirmation
button
6-pin FireWire
Cooling Fan
(removable)
RAID Mode LEDs
Mode switch
Fan switch
Drive Power/
Activity LEDs
Interface
LEDs
Power
button
Drive Status LEDs
Front Door
release
Fan Mode/Speed LEDs
Power LED
3
9-pin FireWire
ports
DIN power
connector
Side View
4
Hardware Installation
1. Secure the included Hard Drive Handles to the hard drives with the
supplied screws and screw driver.
2. Press the front door in to release the latch and open the door. The
door is also removable for easier access.
3. Inside will be a metal drive cage in front of the drive bays. Along
the top of the drive cage are two small tabs. Press them down to
release the cage and remove it.
5
4. Remove the cardboard inserts (if first time setup) and then insert the
hard drives into the slots. If installing less than 4 drives, ensure a
drive is installed in the bottom slot. This will help when reinstalling
the metal cage. Hard drives can be removed from the enclosure by
pressing down on the handles, then pulling them out.
5. Once all of the hard drives are installed, reinstall the metal cage
and front door. Make sure the bottom of the cage stays inside of the
track before closing the cover.
6. Connect the power adapter DIN connector into the side of the
enclosure and power up the enclosure.
Driver Installation
Windows 2000/XP/Server 2003/Vista, Mac OS X, Linux
No driver installation is required for these operating systems, as this
enclosure is natively supported, so the drivers are already installed.
6
How to Use
Hard Drive DIP Switch
The DIP switches on the rear of the hard drive enclosure first needs
to be set, depending on the number of installed hard drives in the
enclosure. The number of hard drives affects the available RAID
modes that can be selected.
Number of
Drives DIP Switch Available RAID Modes
2RAID0 (Span), RAID0 (Stripe),
RAID1 (Mirror)
3 RAID3, RAID5
4
RAID0 (Span), RAID0 (Stripe),
RAID3, RAID5,
RAID10 (Stripe+Mirror)
RAID Mode
While the enclosure is powered on, press and hold the ‘Mode’ button
for three (3) seconds until one of the RAID LED’s start to flash.
Pressing the ‘Mode’ button will now switch between available RAID
modes. Once set, press the ‘Confirmation’ button in the back of the
enclosure. The enclosure will power off. Once powered back on, it will
be set for the desired RAID mode.
7
LED Status Description
ON SPAN: Spanning concatenates multiple hard
drives into a single large disk. Provides no
performance or redundancy benefits.
OFF
ON
RAID 0 (Stripe): Striping combines multiple disk
into a single large disk array. The data is split
evenly across each disk simultaneously. Read/
write performance is increased as a result, but
failure of any one disk will make the entire array
unusable.
OFF
ON RAID 1 (Mirror): Mirroring writes the same data
across multiple disk, creating a mirror copy. This
provides redundancy in case one drive fails.
OFF
ON
RAID 3: Uses striping to write data to multiple
disks like RAID 0, but reserves one disk for
parity. The single parity disk is a bottle-neck for
writing since every write requires updating the
parity data. Failure of any one disk will still allow
access to the data, until the disk is replaced.
OFF
ON RAID 5: Uses striping to write data to multiple
disks simultaneously and distribute parity
across multiple disks. Failure of any one disk
will still allow access to the data, until the disk is
replaced.
OFF
ON RAID 01 (0+1): Creates a mirrored array, then
stripes each mirrored disk. Combines the
performance of RAID 0 with the redundancy of
RAID 1.
OFF
Andere Handbücher für S354UFER
1
Inhaltsverzeichnis
Andere StarTech.com Gehäuse Handbücher
StarTech.com
StarTech.com UNI2510U2V Bedienungsanleitung
StarTech.com
StarTech.com 8STUNI251BMU33 Bedienungsanleitung
StarTech.com
StarTech.com UNI2510U2V Bedienungsanleitung
StarTech.com
StarTech.com S355BU33ERM Bedienungsanleitung
StarTech.com
StarTech.com S2510SM12U33 Bedienungsanleitung
StarTech.com
StarTech.com RK123WALHM Bedienungsanleitung
StarTech.com
StarTech.com S2510BU33PW Bedienungsanleitung
StarTech.com
StarTech.com SAT3510U2V Bedienungsanleitung
StarTech.com
StarTech.com S351BMU33ET Bedienungsanleitung
StarTech.com
StarTech.com RK1219WALHM Bedienungsanleitung
StarTech.com
StarTech.com SAT3520U2R Bedienungsanleitung
StarTech.com
StarTech.com S252SMTB3 Bedienungsanleitung
StarTech.com
StarTech.com SAT1810U2 Bedienungsanleitung
StarTech.com
StarTech.com S251BPU313 Bedienungsanleitung
StarTech.com
StarTech.com SLSODDU33B Bedienungsanleitung
StarTech.com
StarTech.com IDECASE525U2 Bedienungsanleitung
StarTech.com
StarTech.com SAT3540U2E Bedienungsanleitung
StarTech.com
StarTech.com S351BU313 Bedienungsanleitung
StarTech.com
StarTech.com S251SMU33EP Bedienungsanleitung
StarTech.com
StarTech.com S3540BU33E Bedienungsanleitung
