StarTech.com SAT3550ESR Bedienungsanleitung

SATA RAID Drive Enclosure

SAT3550ESR Instruction Manual

Actual product may vary from photo

5 Drive 3.5” eSATA to SATA RAID Drive Enclosure

FFCCCCCCoommpplliiaanncceeSSttaatteemmeenntt

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

UUsseeooffTTrraaddeemmaarrkkss,,RReeggiisstteerreeddTTrraaddeemmaarrkkss,,aanndd

ootthheerrPPrrootteecctteeddNNaammeessaannddSSyymmbboollss

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and

do not represent an endorsement of a product or service by StarTech.com, or an

endorsement of the product(s) to which this manual applies by the third-party company in

question. Regardless of any direct acknowledgement elsewhere in the body of this

document, StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

TTaabblleeooffCCoonntteennttss

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Host Controller Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

SiI 4726 Manager GUI Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Hardware Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Hard drive installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Connecting the Drive Enclosure to the computer . . . . . . . . . . . . . . . .4

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Status Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Elements of the Status window . . . . . . . . . . . . . . . . . . . . .6

Basic Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Advanced Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Multiple Volume Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Manage Configuration files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Partition Configured Volumes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Administering the SAT3550ESR Drive Enclosure . . . . . . . . . . . . . . . . . . . . .20

Configuring the SAFE Volume Rebuild Storage Policy . . . . . . . . . . .21

Email Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Install New Firmware & Software . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Editing the UserConfig.xml

Monitoring and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Storage Policies Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Instruction Manual

Thank you for purchasing a StarTech.com 5 Drive 3.5” eSATA to SATA RAID Drive

Enclosure. A cost-effective storage solution, SAT3550ESR provides enhanced data

protection, high-performance storage and plug-and-play functionality, making it a simple

solution for professional or home users to replicate data and maintain data security.

IInnttrroodduuccttiioonn

Features

BBeeffoorreeYYoouuBBeeggiinn

•Five separate drive bays maximize external storage capacity

•Support for both 2.5” and 3.5” SATA hard drives

•Single rear eSATA interface to host to manage access to each hard drive

•Supports data transfer speeds up to 3 Gbps

•Each hard drive bay is hot swappable

•x86 platform: An Intel Pentium 3 500MHz equivalent or faster

System Requirements

•Mac platform: A Mac G4 500MHz or faster

•CD-ROM drive (driver installation)

•64 MB RAM

•Dual 80mm internal fans for enhanced hard drive cooling

•250 MB of available hard drive space

•SVGA capable monitor

•Mouse/pointing device

•External SATA cable connection between Host computer and SAT3550ESR

•Microsoft Windows 2000/XP/Server 2003 or Mac OS X with latest updates

Package Contents

•1 x External Drive Enclosure •1 x Driver/Application CD

•1 x 2m eSATA Cable •1 x Power Cord

•1 x Instruction Manual

•1 x Screw Kit

•1 x PCI-Express 1x Host RAID

Controller Card

Instruction Manual

IInnssttaallllaattiioonn

Host Controller installation

In order to provide a software and hardware link between the host computer and the

SAT3550ESR Drive Enclosure, it is required that the included PCI Express Host

Controller be installed on the host computer. You may also use another Host Controller,

provided it features port multiplier support, however it is not guaranteed that all host

controllers with port multiplier support are compatible with the drive enclosure.

1. Insert the Driver CD into your CD/DVD-ROM drive

2. Power down the computer, ensuring the system is unplugged and you are grounded.

3. Remove the cover of your system (see your computer's user manual for details, if

necessary) and gently turn your computer onto its side, so that the PCI Express

expansion slot on the motherboard is facing upward.

4. Locate an empty PCI Express slot and remove the metal plate that covers the

corresponding rear bracket. You may need a Phillips screwdriver to perform this step.

Retain the screw! You will need it to secure the card later.

5. Gently insert the card into the empty slot, making sure it is firmly seated.

6. Secure the card to the rear panel, using the screw you removed in Step 3.

7. Power on the computer. Once the operating system is fully booted, insert the Driver

CD (included) into the CD/DVD-ROM drive. You will notice several message

balloons originating in the taskbar, indicating that the required drivers are being

installed for the devices found.

The SiI 4726 Manager GUI provides a convenient way to manage disks installed within

the Drive Enclosure. To install the Sil 4726 Manager GUI:

1. Locate the Setup.exe file, by browsing to the BT3045_Manager\

SiI_4726_Graphic_User_Interface_V4.0.0.9 subfolder.

2. Double-click on the Setup.exe file to begin installation. Follow the on-screen prompts

to complete installation.

Sil 4726 Manager GUI installation

SiI 3132

SATALink

Controller

Once the card has been properly installed,

you can verify that it is detected by the

operating system by browsing to the

device manager (i.e. Start - Control Panel

- System - Hardware - Device Manager):

Instruction Manual

Error Condition Indicator

OK Indicator

Key Lock

Drive

Bays

Safety latch

Rear PanelFront Panel (closed)

Power

Button

Hardware Guide

Front Panel (open)

Front Panel

Door

eSATA

port

Power Port

Instruction Manual

1. Open the Front Panel Door, exposing the individual Drive Bays.

2. To remove one of the Drive Bays from the enclosure, slide the Safety Latch on the

front panel of the bay, to the left. Gently press the cover of the Drive Bay until you

hear a click, allowing the Retaining Arm to move freely. Grasp the Retaining Arm and

pull the Drive Bay from the enclosure.

3. Align the screwholes provided on the base of the Drive Bay, with the screws provided

on the base of the hard drive. Secure the hard drive to the metal base of the Drive

Bay removed in step 2, using the included screws as necessary.

4. Once the drive has been secured to the Drive Bay, replace the Drive Bay by gently

sliding it into the empty slot, ensuring the Drive Bay is properly resting on the internal

guide rails provided. The SATA data and power connectors located on the back of the

hard drive should be in direct contact with the connectors located internally at the

back of the enclosure.

5. Gently press the Retaining Arm (see step 2) until it locks back in place, now flush with

the other drive bays.

6. Slide the Safety Latch to the right, to ensure that the installed drive is not accidentally

released from the enclosure.

7. Repeat steps 1-6, for the remaining hard drives you wish to install.

8. Once you have secured each hard drive within the enclosure, close the Front Panel

Door. Optionally, you can lock the Front Panel Door in place, using the keys provided,

by turning the lock 1/4 turn in a clockwise direction.

Hard drive installation

Connecting the Drive Enclosure to the computer

To connect the SAT3550ESR Drive Enclosure to the host computer

: Connect one

end of a standard eSATA cable to the port located on the rear panel of the Drive

Enclosure; connect the remaining end of the eSATA cable to the eSATA port provided by

the the newly installed host controller on the host computer.

To power the SAT3550ESR Drive Enclosure:

Connect the female portion of the

included power cable to the male power port located on the rear panel of the Drive

Enclosure. Connect the remaining end of the power cable to an available power outlet.

Press and hold the Power button for three seconds, (located on the front of the Drive

Enclosure). Verify that the drives are detected by the operating system (in Windows, for

example, browse to My Computer, where the newly attached drives should appear).

Instruction Manual

CCoonnffiigguurraattiioonn

Introduction

Windows

1. Click on the Start button, and select All Programs. Click on Sil 4726 Manager to

launch the configuration program.

2. From the window that opens, you are able to monitor the status of the connected

drives:

Mac OS X

1. Launch the Finder and locate the SiI 4726 program within the Applications - Utilities

- SteelVine folder. Click the SiI 4726 icon to start the SiI 4726 Manager. If the launch

sequence does not locate an active Daemon, a warning will appear; click OK to

advance past the warning.

2. You will be asked to enter the administrator password. Once you have done so, click

OK to proceed.

3. A notice will appear as the launch sequence attempts to start the Daemon. Click OK.

If the Daemon fails to start, an error message will be displayed. Please follow the

recommendations in the error message to correct the problem.

4. The window that will open (Status Window) allows you to monitor the status of the

installed drives.

Instruction Manual

Status Window

The Status Window provides basic information pertaining to the installed drives and their

respective configuration:

1Serial Number

System Status

Drive Status

Capacity Information

Elements of the Status window

System Status section

Temp

: Indicates the current internal temperature of the SAT3550ESR Drive Enclosure

Fan Speed

: Indicates the system fan status. Use this data to monitor possible

malfunctions

Drive Status section

Box Status

: Indicates the drive status: Normal, Rebuilding, Unplugged, Needs

Rebuild, New Drive, Wrong Slot

Drive S/N

: Shows the unique serial number assigned by the disk manufacturer

Exp. S/N

: Shows the expected serial number of the hard disk drive. The Daemon

compares the expected and actual drive serial numbers to detect when a

drive’s status changes.

Capacity Information section

Policy

: Shows the storage policy configured for each volume.

Total

: Shows the combined capacity of the volume.

Drive # :

Shows capacity information for each hard disk

Capacity :

Shows the full amount of storage space (in GB) available on each hard disk.

Volume :

Shows the total volume capacity and the drive capacities assigned to each

volume.

File Menu

Change Password

: Opens a dialog to establish a new password.

Scan Devices

: Refreshes the status list details presented on the Status window.

Change Connections

: Opens a dialog to establish remote connections.

Edit Menu

Configure Box

: Opens the Basic Configuration Wizard. From here, you can access the

Advanced Configuration Wizard.

Specify Policy

: Opens the Rebuild Policy dialog.

Specify Email Notification

: Sends email notification for the selected items.

Event Log

: Opens the Event Log viewer.

Specify Firmware

: Opens the Firmware Selection dialog.

Toolbar button functions

Instruction Manual

Configure Box -

Opens the Basic Configuration Wizard.

Specify Policy

: Opens the Rebuild Policy dialog

Specify Email Notification

: Sends email notification for the selected items

Event Log

: Opens the Event Log viewer

Specify Firmware

: Opens the Firmware Selection dialog

Inhaltsverzeichnis

Andere StarTech.com Gehäuse Handbücher

StarTech.com

StarTech.com SAT2510U2F Bedienungsanleitung

StarTech.com

StarTech.com S252BU313R Bedienungsanleitung

StarTech.com

StarTech.com InfoSafe S252U2ERR Bedienungsanleitung

StarTech.com

StarTech.com IDECASE525U2 Bedienungsanleitung

StarTech.com

StarTech.com M2E1BMU31C Bedienungsanleitung

StarTech.com

StarTech.com SLSODDU33B Bedienungsanleitung

StarTech.com

StarTech.com S354UFER Bedienungsanleitung

StarTech.com

StarTech.com SAT3520U2R Bedienungsanleitung

StarTech.com

StarTech.com ESATCASE2 Bedienungsanleitung

StarTech.com

StarTech.com RK2537BKM Bedienungsanleitung

StarTech.com

StarTech.com UNI2510U2V Bedienungsanleitung

StarTech.com

StarTech.com SAT3510BU3 Bedienungsanleitung

StarTech.com

StarTech.com S352BMU3N Bedienungsanleitung

StarTech.com

StarTech.com M2-USB-C-NVME-SATA Bedienungsanleitung

StarTech.com

StarTech.com 8STS25SLOTR Bedienungsanleitung

StarTech.com

StarTech.com UNI3510U2 Bedienungsanleitung

StarTech.com

StarTech.com S251BPU313 Bedienungsanleitung

StarTech.com

StarTech.com RK1520WALHM Bedienungsanleitung

StarTech.com

StarTech.com S3510SMU33 Systemhandbuch

StarTech.com

StarTech.com S354UFER Bedienungsanleitung

StarTech.com

StarTech.com IDECASE35NAS Bedienungsanleitung

StarTech.com

StarTech.com RK920WALM Bedienungsanleitung

StarTech.com

StarTech.com SAT3520U3R Bedienungsanleitung

StarTech.com

StarTech.com S251BU31C3CB Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Nexans

Nexans WTC05 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung