Summit CSW-34 Bedienungsanleitung

FELIX STORCH, INC.

SUMMIT APPLIANCE DIVISION®

INSTRUCTION MANUAL FOR MODEL(S):

S-23

S-23L

SW-23

CSW-34

Thank you for your trust and for buying this appliance. We hope it will successfully

serve its purpose for many years.

COMPACT REFRIGERATOR

The Model Types

The S-23 is an upscale compact cube refrigerator available in white. It has a cord

extension of 8 feet. This unit contains a reversible door, an ice cube compartment with its

own door, and door storage for larger bottles.

The S-23L is the same as the S-23 but includes a side mounted lock.

The SW-23 is the same as an S-23 but with a walnut grain door and brown sides.

The CSW-23 is the same as the S-23 but with a walnut grain door and copper tone sides.

Instructions for Use

Before Putting Into Use

Instructions for Use

These instructions for use are intended for the user. They describe the appliance and

the correct and safe way to use it. The instructions were prepared for various

types/models of refrigerators therefore you may find in it descriptions of some

accessories and functions that your appliance may not have.

•Before connecting the appliance to the power supply, leave it standing for

about 2 hours, which will reduce a possibility of malfunctions in the cooling

system due to transport handling.

•Clean the appliance thoroughly; especially in the interior (See Cleaning and

Maintenance).

•Use a 120 volt, 60HZ outlet. Do not use an extension cord.

•Use a 3 prong grounded wall outlet.

Mounting Instructions

Integrated appliances are equipped with instructions for mounting the appliance into

the kitchen unit.

The appliance should be mounted by qualified technicians and instructions are for

their use only.

We Care for the Environment

•Our appliances are distributed in packaging made of environmental

friendly material which could safely be recycled, disposed of or destroyed

without any effects on the environment whatsoever.

•Our instruction manuals are printed either on recycled paper or chlorine

free bleached paper.

Tips for Energy Savings

•Try not to open the door too often, especially when the weather is hot and

humid. Once you open the door try to close it as soon as possible.

•Every now and then check if the appliance is sufficiently ventilated

(adequate air circulation behind the appliance).

•Set thermostat from higher to lower settings as soon as possible

(depending on how full the appliance is, ambient temperature etc...).

•The coils on the rear of the refrigerator should be cleaned and free of dust

or any other impurities.

•Ice and frost layer increase energy consumption, so clean the appliance as

soon as the layer is 1/8” thick.

•Always consider instructions stated in sections Energy Saving Tips,

otherwise the energy consumption is substantially higher.

Instructions for Use

Important

To reduce the risk of fire, electrical shock,

Warning! or in

when usin

our appliance,

follow these basic precautions:

•Read all instructions before using the appliance.

•If you bought this appliance to replace an old one equipped with a lock

that cannot be opened from inside (lock, bolt), make sure that the lock

is broken. This will make it impossible for children to lock themselves

inside the appliance and suffocate.

•The appliance must be correctly connected to the power supply.

•If the food has a strange smell or color throw it away because it is very

likely that it is spoiled and therefore dangerous to eat.

•Disconnect the appliance from the power supply before repairing and

cleaning it (only a qualified technician should repair it).

•For the sake of environmental protection be careful not to damage the

rear wall of the appliance (the condenser unit or the tubes when

moving the refrigerator) or any part of the refrigerating system inside

the appliance. Use only enclosed tools or tools recommended by the

manufacturer.

•The refrigerating system of the appliance is filled with refrigerant and

oil, so when the appliance is damaged handle it with care and dispose

of it in compliance with the environmental protection precautions.

•Before throwing away your old refrigerator please remove the doors

and leave the shelves in place so that children may not easily climb

inside.

•DANGER: Risk of child entrapment.

•The rating plate is inside the appliance or outside on the rear wall.

Disposing of the Worn Out Appliance

•When your appliance finally wears out, dispose of it. If the appliance

has a lock, break it to prevent eventual accidents (danger of children

getting locked inside the appliance).

•The refrigerating system of the appliance is filled with refrigerant and

insulating substances which should be separately treated and

processed, you should call your nearest authorized service agent or

specialized servicing center if they cannot be contacted call your local

authorities or your distributor to remove the refrigerator. Be careful

not to damage the tubes on the rear wall of the appliance (danger of

pollution).

Instructions for Use

Placing and Installation

Choosing the Right Place

Place the appliance in a dry and regularly ventilated room. Allowed ambient

temperature depends on the model (class) of the appliance. It is located on the

rating plate of the appliance. Make sure the appliance is on a leveled floor that is

strong enough to support the appliance when it is fully loaded.

Class Ambient Temperature

SN (sub-normal) from + 56°F to + 90°F

N (normal) from + 62°F to + 90°F

ST (sub-tropical) from + 64°F to +100°F

T (tropical) from + 64°F to +120°F

The appliance may be exposed to lower or higher temperatures but only for

shorter period of time and the temperature should never be lower than 41°F.

Never place the appliance near heat emitting devices (e.g. cooker, radiator, water

heater or similar devices) and do not expose it to direct sunlight. The appliance

should be positioned 3cm from the electric or gas cooker. Behind the appliance

there should be at least 200 cm² wide and above the appliance at least 5 cm away

from the appliance in order to assure adequate ventilation of the condenser unit.

Placing the Self-Standing Appliance

•It is important to make sure the appliance is leveled evenly to prevent

falling.

•Do not place the appliance in direct sunlight and sources of heat

(stove, heater, radiator, etc.). Direct sunlight may affect the acrylic

coating and heat sources may increase electrical consumption.

•The appliance with the ventilation grid may be placed close to the

wall. The grid enables sufficient air circulation that is required for

adequate ventilation of the rear wall.

Connection to Power Supply

Connect the appliance with the cable and plug to the power supply socket outlet

with a ground terminal (safety socket).

“DO NOT USE AN EXTENSION CORD.”

Required nominal voltage and frequency are indicated on the rating plate.

The connection to the power supply and grounding has to be made according to

current standards and regulations. The appliance resists temporary voltage

tolerance up to -15 to 10%.

Instructions for Use

Description of the Appliance

NOTE:

•The appliance can be equipped with various accessories, depending on the

model of the appliance.

•Door handles are in various shapes, depending on the model.

•Various accessories (additional shelves) can be purchased at authorized

centers.

Freezing Compartment

Used for making ice cubes.

Drip Tray

Catches melted water when defrosting.

Control Knob

It rotates to adjust the refrigerator temperature.

Slide Out Shelf

Odor resistant, rustproof and plastic coated steel shelf.

Bottle Rack

The bottle rack is intended for storing bottles.

Instructions for Use

Operation Control

The refrigerator can be adjusted from colder to warmer by turning the

Temperature Control knob. Colder temperature can be achieved by turning the

control knob clockwise towards the “max” position. Warmer Temperatures can be

reached by turning the control knob counterclockwise towards the “min” position.

Temperature Selection

Higher settings on the knob (max) mean colder temperatures in all

compartments of the appliance. The temperature in the interior of the

appliance may even drop below 35°F. Use the higher thermostat setting

only when required or recommended. We recommend that you set your

thermostat in the middle for standard temperature.

Changing the thermostat will affect the temperature inside of the

appliance; therefore choose your temperature wisely.

When the thermostat is on the OFF position the appliance does not

operate.

Temperature in the refrigerator also depends on how often you open the

door.

Changing the Direction of Opening the Door

If you find the direction of opening the door on your appliance inconvenient, you

can change it. Holes on the opposite side have already been prepared at the

factory.

Some screws are covered with caps. Remove the caps before undoing the

screws.

Take off the upper hinge cap and unscrew the upper and lower hinges.

Remove the kick plate and place it in its new position.

Unplug the holes covering the holes on the opposite side of the appliance

door.

Undo the fastener of the upper hinge and fix it to the opposite side of the

appliance.

Put the door on the upper hinge fastener.

Fix the upper hinge and cover it.

Unscrew the handle and replace it to the opposite side (not for handles

mounted horizontally).

Plug the remaining holes with decorative caps.

Check the gasket, it should not be creased and should seal well.

Instructions for Use

Maintenance and Cleaning

Automatic Defrosting of the Refrigerator

There is no need to defrost the refrigerator, because the ice depositing on the inner

back wall is defrosted automatically.

Ice is depositing on the inner back wall during the compressor operation; later on,

when the compressor is not operating, ice is defrosting and water drops, collects

and drains through the outlet in the inner back wall into the drain pan situated

above the compressor where it evaporates.

Cleaning the Appliance

Disconnect the power supply before cleaning the appliance. Do not use coarse or

Aggressive cleaning agents as you can damage the surface.

Clean the exterior with water and detergent. Varnished surfaces are

cleaned with soft cloth and an alcohol based cleaning agent (for example

glass cleaners). You may also use alcohol (ethanol or isopropyl alcohol).

The application of abrasive and especially aggressive cleaners, such as

stainless steel cleaners, is not appropriate for the cleaning of plastic and

coated parts.

Remove the detachable accessories in the interior of the appliance and

clean it with water and liquid detergent. Plastic parts cannot be washed in

a washing machine.

Wash the interior of the appliance with lukewarm water, in which you add

one or two spoonfuls of vinegar.

Every now and then wipe the condenser on the rear wall. Use a soft non-

metal brush or vacuum cleaner.

Do not forget to clean the defrost water receptacle above the refrigerators

compressor (do not remove the receptacle). After cleaning, connect the

appliance to the power supply and reload the packages.

Switch Off the Appliance When Not in Use

If you do not intend to use the appliance for an extensive period of time set the

thermostat knob to the OFF (0) position and disconnect the power supply. Then

take out the foods and clean the appliance. Leave the door slightly open.

Instructions for Use

Trouble-Shooting Guide

During the service of your appliance, you can come across some troubles that in

most cases result from improper handling of the appliance that can easily be

eliminated.

The Appliance Fails to Operate After Connecting to the Power Supply

Check the supply in the outlet socket and make sure the appliance is

switched on (thermostat in the operating position).

Continuous Operation of the Refrigerating System

The door was frequently opened or it was left open too long.

The door is not properly closed (the door may sag; the gasket may be

polluted or damaged).

Perhaps you have overloaded the appliance with fresh foods.

The reason may be inadequate ventilation of the compressor and

condenser (assures adequate air circulation and wipe off the condenser).

Ice Formation on the Inner Rear Wall

As long as the defrost water runs to the channel and through the opening to the

drain pan on the compressor, automatic defrosting of the appliance is assured. In

case the ice formation on the inner back wall is increased (1/8”), ice should be

manually defrosted.

Set the thermostat knob to OFF (0) position and leave the door open. Never use

electric devices for defrosting and do not scrape the ice or frost layer with sharp

objects. After completed defrosting, turn the knob to desired position and close

the refrigerator door.

The cause of increased ice formation may be one of the following reasons:

-The door does not seal well (clean the gasket if it is contaminated,

or replace it if it is damaged).

-The door was frequently opened or it was left opened for too long.

-The food stored in the refrigerator was warm.

-The food or dish is touching the inner back wall.

Water is Leaking from the Refrigerator

In case the discharged water outlet is clogged, or the defrost water drips over the

channel, or water leaks from the refrigerator just clean the clogged opening with a

plastic straw. Manually defrost the increased ice layer. See “Ice Formation on the

Inner Back Wall”.

Instructions for Use

Noise

Cooling in refrigerating-freezing appliances is enabled by the refrigerating system

with the compressor, this produces noise. How noisy the appliance is depends on

where it is placed, how it’s used and how old the appliance is.

During the operation of the compressor, a liquid noise is heard and when

the compressor is not operating a refrigerant flow is heard. This is a

normal condition and it has no influence whatsoever on the lifetime of the

appliance.

After starting the appliance, the operation of the compressor and the

refrigerant flow may be louder and this does not mean something is wrong

with the appliance. The noise will reduce gradually, this will not affect

the lifetime of the appliance.

Sometimes unusual and strong noises occur which is rather unusual for the

appliance. This noise is often a consequence of inadequate placing. To

avoid the noise make sure the appliance is placed and leveled firmly on a

solid base. Make sure the appliance is not touching the wall or kitchen

units standing next to it. And always make sure you check the accessories

in the interior of the appliance; they should be placed correctly in their

positions. Check the bottles, tins and other vessels that might touch each

other and rattle.

Before Calling for Service

Check the plug and fuse.

Test the outlet with a lamp.

Be sure the control is not set to OFF.

Read the manual, especially the items under the Use and Care sections.

You may find the answer to your questions.

If you don’t find the answer to your questions in this manual, find the

unit model number (on the upper back of the refrigerator) and contact

your Summit Appliance Dealer.

Specifications are Subject to Change Without

Notice.

Instructions for Use

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Summit Kühlschrank Handbücher

Summit

Summit FFBF283SS Bedienungsanleitung

Summit

Summit FFBF101SS Bedienungsanleitung

Summit

Summit SCR600BLBISHWO Leitfaden

Summit

Summit SPR6-OS Bedienungsanleitung

Summit

Summit CT661 Bedienungsanleitung

Summit

Summit AL750 series Leitfaden

Summit

Summit ALR47B Bedienungsanleitung

Summit

Summit FFBF192SS Bedienungsanleitung

Summit

Summit R17FF Bedienungsanleitung

Summit

Summit ALRF49B Bedienungsanleitung

Summit

Summit FF471WBI/FC Bedienungsanleitung

Summit

Summit FF590 Bedienungsanleitung

Summit

Summit GLOBAL INDUSTRIAL GIDIFFBF283SS Bedienungsanleitung

Summit

Summit FF7BSSHH Leitfaden

Summit

Summit FF43SS Leitfaden

Summit

Summit FFBF240W Bedienungsanleitung

Summit

Summit FF-874W Bedienungsanleitung

Summit

Summit FF-874 Series Bedienungsanleitung

Summit

Summit FFBF285SS Bedienungsanleitung

Summit

Summit FF1325SSIM Bedienungsanleitung

Summit

Summit FF61 Bedienungsanleitung

Summit

Summit FF7L-BLSSTB Leitfaden

Summit

Summit CM406W Bedienungsanleitung

Summit

Summit SPRF34D Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung