Swift SW350B Bedienungsanleitung
User Guide: SW350B
Welcome to your Swift SW350B microscope! Whether you are a seasoned professional
or a beginner hobbyist, Swift has the perfect microscope for you.
This quick-start guide will introduce you to the components of your new microscope and
help you begin to use it. For more information about our microscopes or customer
service requests, please visit www.swiftoptical.com.
Table of Contents
I. Specifications 2
II. Parts of the microscope 3
III. Assembly and set up 3
IV. Using the microscope 3
V. Caring for your microscope 5
VI. Troubleshooting 5
VII. Warranty information and customer support 7
1
I. Specifications
Model
SW350B
Head
360° rotatable Binocular Siedentopf
Inclination
30°
Eyepieces
Wide-field 10X and 25X pairs
Interpupillary distance
48-75mm
Diopter adjustment
On left tube, +/-5dp
Nosepiece
Quadruple revolving
Objectives
Achromatic
4X, NA 0.1, working distance 37.5mm
10X, NA 0.25, working distance 7.35mm
40X(Spring), NA 0.65, working distance 0.29mm
100X (Spring, Oil), NA 1.25, working distance 0.18mm
Magnifications
40X, 100X, 250X, 400X, 1000X and 2500X
Stage
Double-layered mechanical stage with slide holder
Stage size
130mmx130mm
Stage X-Y range
70mmx30mm
Upper limit stop
Rack stop preset but adjustable
Condenser
NA 1.25 with iris diaphragm
Focusing
Coaxial coarse and fine focusing system
Illumination
Built-in 1W LED transmitted illumination with intensity control
Power
110-240V AC adapter (included)
2
II. Parts of the microscope
III. Assembly and set up
Carefully remove the microscope from the box and set it on a sturdy, flat surface.
Remove the plastic covers from the eyepiece holders on the microscope's head, then
place eyepieces into the holders. Locate the power adapter and attach it to the
microscope, then plug it in. Turn the microscope on by pressing the power button on the
back of the base.
IV. Using the microscope
Turn the microscope on and use the illumination intensity control wheel to set the lamp
on the lowest brightness setting.
3
Clip a slide into the slide holder on the stage. Use the X-Y translational control knobs on
the right side of the stage to move the stage front to back or the slide holder left to right
to center the specimen over the bulb.
Move the eyepieces closer together or further apart until you see one image when you
look through them. Adjust the bulb brightness to a comfortable intensity with the dimmer
wheel.
Always start with the lowest power objective lens, in this case the 4X objective, centered
over the stage. Look through the eyepieces and bring the image into focus by slowly
turning the larger coarse adjustment focus knob to bring the stage closer to the
objective. Once an image forms, switch to the blue fine adjustment focus knob to
fine-tune for clarity or to see the various layers of the specimen you are examining. You
may also use the diopter adjustment control on the eyepiece holder at this time to
further fine-tune image clarity. Look at other parts of the slide by using the X-Y
translational control knobs to move the slide holder once the specimen is in focus.
Increase magnification by rotating the nosepiece clockwise to a higher magnification
objective, taking care not to strike the slide with the objective, as doing so may damage
the glass on the slide, the objective, or both. If you cannot move the objective into place
without making contact with the slide, use the coarse focus knob to move the stage
down and away to make room before changing magnification.
Adjust the focusing ring on the iris aperture diaphragm to change the resolution of the
image. The condenser can be manually moved closer to or farther from the stage by
rotating the metal knob.
For best results with the 100X objective, use the included immersion oil. Rotate the
nosepiece so that the 100X objective is near, but not on the specimen slide. Then place
a drop of the included immersion oil onto the cover slip. Slowly rotate the 100X objective
into place so that it comes into contact with the immersion oil. Adjust focus until your
specimen comes clearly into view. (Note: Immediately after use, always gently wipe the
oil off of the objective lens and the cover slip with lens paper moistened with a small
amount of ethyl or isopropyl alcohol. Do not use immersion oil with the 4X, 10X, or 40X
objectives.)
4
V. Caring for your microscope
As with any quality instrument, your microscope should be stored in a cool, dry place.
Use the dust cover to protect the microscope when not in use. If necessary, clean the
lenses with a soft brush or compressed air to gently remove dust.
Avoid touching the optical surfaces directly and never disassemble the optical
components of the microscope. When not using eyepieces, use the plastic covers to
protect the eyepiece lens holders and ocular lens.
VI. Troubleshooting
If you have a problem, you may be able to correct it yourself. Here are some common
issues and easy solutions you can try before calling customer support for service.
*Caution: Never disassemble the electrical, mechanical, or optical components. This
servicing should only be done by a Swift technician.
Issue
Possible cause
Solution
Visual field is uneven, or
image is dark at the edges
Nosepiece is not locked in
place to center the
objective lens
Turn nosepiece until you
hear a click to center the
objective lens
Slide is not centered over
the bulb, leaving part of the
specimen unilluminated
Center the slide over the
bulb with the X-Y
translational control knobs
Dirty objective or eyepiece
lens
Clean with compressed air
or soft brush
Iris aperture is closed too
far
Open the iris aperture
wider
5
Visual field is blurry or dirty
Dirty objective or eyepiece
lens
Clean with compressed air
or soft brush
The slide is dirty
Clean the slide with glass
cleaner
Eyepiece or objective lens
not fully screwed into place
Tighten eyepiece or
objective lenses
Poor image quality
No cover slip on the
specimen
Place glass cover slip over
the specimen
Slide is too thick or too thin
Use a lab-quality slide
Slide is placed upside
down on the stage
Flip the slide over so that
the cover slip is facing up
Oil on objective lens
Wipe the lens off with soft
cloth and glass cleaner
Iris aperture is too narrow
or too wide
Adjust the iris aperture
Image moves while
adjusting focus
Slide is shifting on the
stage
Reposition slide more
securely in the slide holder
Light is too dim
Iris aperture is closed too
far
Open the iris aperture
wider
Bulb setting is too low
Increase intensity on the
control wheel
Condenser lens is dirty
Wipe the condenser lens
off with a soft cloth
Voltage is too low
Use the supplied power
adapter
6
Objective lens collides with
the slide when switching
from a lower to a higher
power objective
Slide is upside down or too
thick
Use a lab-quality slide or
flip the slide over so the
cover slip is facing up
Stage is set too close to
the objectives
Lower the stage with the
coarse focus knob
Safety rack stop needs
adjustment
Adjust the safety rack stop
to stop the stage farther
from the objectives
Image won't come into
focus when using a
higher-powered objective
Slide is upside down
Flip the slide over so the
cover slip is facing up
Slide is not moving when
using the X-Y translational
control knob
Slide has come unclipped
from the holder
Reposition slide in the
holder and secure with clip
Lamp does not turn on
No power source
Check that the adapter is
fully connected or that
batteries are installed
Bulb has burned out
Replace the bulb
Lamp flickers while on
Bulb is not inserted into the
socket correctly
Check to make sure the
bulb is fully screwed into
the socket
Power adapter is not fully
plugged in
Check to make sure that
the adapter is fully
connected to wall socket
and to the microscope
VII. Warranty information and customer support
Our microscopes are manufactured to meet ISO 9001 standards. Swift warranties are
as follows:
● Five (5) Year Warranty for Microscopes: Microscopes come with a five (5) year
warranty against manufacturing defects
7
● One (1) Year Warranty for Accessories: Microscope accessories such as
eyepiece cameras, dust covers, power supply cords, etc., come with a one (1)
year warranty
All warranties start from the original date of purchase. Swift provides the repair or
replacement of warrantied parts for free, including labor, during the warranty period.
Proof of original purchase is required. Buyers are responsible for shipping to and from
our warehouse for warranty services. The warranty does not cover damages resulting
from normal wear and tear, abuse, or unauthorized repairs.
For more information or to submit a repair request, please contact our Customer
Support department:
Tel: 877-967-9438, option 1
Email: [email protected]
Disclaimer: We are constantly working to improve our instruments and to adapt them in
response to customer feedback. These improvements occasionally involve small
modifications to the mechanical structure and optical design of our microscopes.
Therefore, some descriptions, illustrations, and specifications in this instruction manual
may vary slightly from the microscope you receive.
Swift Optical Instruments, Inc.
(877) 967-9438
www.swiftoptical.com
8
Inhaltsverzeichnis
Andere Swift Mikroskop Handbücher
Swift
Swift STELLAR 1 Series Bedienungsanleitung
Swift
Swift M3 Bedienungsanleitung
Swift
Swift M10L Series Bedienungsanleitung
Swift
Swift S41-20 Bedienungsanleitung
Swift
Swift 880 Series Bedienungsanleitung
Swift
Swift S7 Series Bedienungsanleitung
Swift
Swift MZ800 Montageanleitung
Swift
Swift M2250 Series Bedienungsanleitung
Swift
Swift SW50 Bedienungsanleitung
Swift
Swift S30 Series Bedienungsanleitung
Swift
Swift M( series Leitfaden
Swift
Swift M2252DGL Series Bedienungsanleitung
Swift
Swift M10D Series Bedienungsanleitung
Swift
Swift Stereo SM80 Montageanleitung
Swift
Swift SW350T Bedienungsanleitung
Swift
Swift M3600 series Bedienungsanleitung
Swift
Swift SM91 Bedienungsanleitung
Swift
Swift M3500 SERIES Bedienungsanleitung
Swift
Swift SW380B Bedienungsanleitung
Swift
Swift M28 Montageanleitung
Beliebte Mikroskop Handbücher anderer Marken
Thermo Scientific
Thermo Scientific Nicolet iN10 Leitfaden
National
National DC3-163 Bedienungsanleitung
KERN Optics
KERN Optics OPE-1 Bedienungsanleitung
OPTIKA MICROSCOPES
OPTIKA MICROSCOPES B-150D Bedienungsanleitung
Prior
Prior Lux POL Bedienungsanleitung
Opitec
Opitec Smartscoop 115615 Bedienungsanleitung
VWR
VWR VisiScope 384 Series Bedienungsanleitung
Nikon
Nikon ECLIPSE E200 POL Bedienungsanleitung
Leica
Leica DI C800 Handbuch
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Bedienungsanleitung
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Bedienungsanleitung
Olympus
Olympus SZ61 Bedienungsanleitung