Swisher Predator Talon WBERC11524C Bedienungsanleitung

OWNER’S

MANUAL

1602 CORPORATE DRIVE, WARRENSBURG MISSOURI 64093

PHONE (660) 747-8183 FAX (660) 747-8650

MODEL NO.

Operation

Service and Adjustment

Repair Parts

REV 15-001

WBERC11524C

swisherinc.com

19900

STARTING SERIAL #:

L115-001001

Read and follow all

Safety Precautions

and Instructions

before operating this

equipment.

IMPORTANT

PREDATOR TALON

COMMERCIAL PRO

24” WALK BEHIND

12V ROUGH CUT

Made In The

USA

of US and Global Parts

In the event you have a claim under this warranty, you must return the product to an authorized

service dealer. All transportation charges, damage, or loss incurred during transportation of parts

submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you

have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The

model number, serial number, date of purchase, and the name of the authorized Swisher dealer from

whom you purchased the mower will be needed before any warranty claim can be processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME

PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not

allow the limitation of consequential damages or limitations on how long an implied warranty may

last, so the above limitations or exclusions may not apply to you. This warranty gives you specific

legal rights and you may have other rights, which vary from state-to-state. This is a limited warranty

as defined by the Magnuson-Moss Act of 1975.

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects

in materials and workmanship for a period of (1) year from the date of purchase by the original

consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to

materials or workmanship. This warranty is subject to the following limitations and exclusions:

TABLE OF CONTENTS

WARRANTY………………....….2

INTRODUCTION………………..3

SAFETY..……………………….3-4

PRE-OPERATING..….……..……4

OPERATION.……………………….5-7

DECALS…..………….……………….8

PARTS BREAKDOWN…………….9-13

MAINTENANCE LOG..……………..15

1) Engine Warranty All engines utilized on our products have a separate warranty extended

to them by the individual engine manufacturer. Any engine service

difficulty is the responsibility of the engine manufacturer and in no

way is Swisher or its agents responsible for the engine warranty. The

Briggs & Stratton Engine Service Hot-Line is 1-800-233-3723.

2) Limitation This warranty applies only to products which have been properly

assembled, adjusted, and operated in accordance with the instructions

contained within this manual. This warranty does not apply to any

product of Swisher that has been subject to alteration, misuse, abuse,

improper assembly or installation, shipping damage, or to normal wear

of product.

3) Exclusions Excluded from this warranty are normal wear, normal adjustments, and

normal maintenance.

SAFETY PRECAUTIONS

This Safety Alert Symbol indicates important messages in this

manual. When you see this symbol, carefully read the message that

follows and be alert to the possibility of personal injury.

Read this manual completely. This machine can amputate hands and feet, and

throw objects. Failure to observe the following safety instructions could result in

serious injury or death.

Thank you for choosing Swisher’s 24” Walk BehindRough Cut. Before

operating your Walk Behind, please read, understand and follow all of the safety

precautions and other instructions explained in this manual. As with all power

equipment, lawn mowers can be potentially dangerous if not properly used.

• Read the manual. Learn to operate this machine safely.

• Always disconnect the spark plug wire and place the wire where it cannot contact the

spark plug, to prevent accidental starting the engine when setting up, transporting,

adjusting or making repairs.

• Keep all shields and guards in place.

• Understand the speed, steering and stability of this machine. Know the positions and

operations of all controls before you operate this machine. Check all of the controls in

a safe area before starting to work with this machine.

• Allow only responsible adults who are familiar with these instructions to operate this

machine. Never allow children to operate this machine.

• Clear the area of objects such as rocks, toys, wire, etc. that can be picked up and

thrown by the blade.

• Be sure the area is clear of other people before mowing. Be aware of the mower

discharge direction and do not point at anyone. Stop the machine if anyone enters the

mowing area. Children are often attracted to the machine and the mowing activity.

Never assume that children will remain where you last saw them. Keep children

under the watchful care of another responsible adult.

•No riders!

• Do not put hands or feet near or under rotating parts.

• Do not mow in reverse. Always look down and behind before and during backing.

• Turn off the blade when not mowing. Before leaving the machine, turn off the blade

and stop the engine.

• Watch for traffic when operating near or crossing roadways.

• Do not operate the mower if it has been dropped or damaged in any manner or if the

mower vibrates excessively. Excessive vibration is an indication of damage. Repair mower

as necessary.

• Dress properly. Do not operate the mower when barefoot or wearing open sandals. Wear

only solid shoes with good traction when mowing.

• Never allow operation by untrained persons.

• Do not operate the machine while under the influence of alcohol or drugs.

• Do not operate on slopes greater than 15 degrees.

• Never tamper with safety devices. Check their proper operation regularly.

• Stop and inspect the equipment if you strike an object. Repair, if necessary, before

restarting. Never make adjustments or repairs with the engine running.

• Mower blades are sharp and can cut. Wrap the blades or wear gloves, and use extra

caution when servicing them.

• Do not operate at too fast a rate.

• Disengage spark plug wire and place where it cannot make a connection.

• Check engine oil. All engines are filled with oil at the factory. Verify oil level and

add if necessary before starting engine (See Engine Owner’s Manual).

• Verify fuel level and add if necessary before starting engine.

• Reconnect spark plug wire.

• Refer to pages 5-7 in this manual for proper operating procedures.

PRE-OPERATING INSTRUCTIONS

The operation of any mower can produce foreign objects to be thrown into the

eyes, resulting in severe eye damage. Always wear certified safety glasses or

wide-vision safety goggles over spectacles before starting any cutting machine and

while operating such a machine.

The operation of any mower produces sound waves that are damaging to the

human ear. Ear protection is recommended.

CAUTION!

Tragic accidents can occur if the operator is not alert to the presence of

children. Children are often attracted to the machine and the mowing

activity. Never assume that children will remain where you last saw them.

OPERATING YOUR NEW WALK BEHIND

INTENDED USE

This is not a lawn mower. The Predator Talon is designed for cutting overgrown brush,

weeds, and other types of organic growth. This unit is capable of clearing small saplings

of 1.5” in diameter or less at a height of approximately 4”.

PROPULSION

The Predator Talon is self-propelled and is controlled by a “GROUND CONTROL”

lever. To engage the drive, put the transaxle in a gear and activate the left lever.

Releasing the lever will disengage the self-propel.

Under most conditions cutting should be done in a low gear (1st or 2nd). Upper gears

should be used for conditions where weeds and brush are thinned out or not as tall. In

confined areas the machine can be pushed forwards or backwards by releasing the

“GROUND CONTROL” lever, placing the transaxle in neutral, and pushing the

machine.

TRAVEL SPEED

Speed can be varied by choosing a higher or lower gear using the gearshift lever at the

rear of the machine or by changing the engine speed with the engine throttle. Do not

adjust speed with the blade engaged. To shift the cutter into reverse, release “GROUND

CONTROL” lever, disengage blade, and rotate the shift lever to the left. When the lever

stops, lift up the reverse lockout latch and continue to move the shift lever to the left until

it stops again.

ENGAGING BLADE

An “OPERATOR PRESENCE” lever and a “BLADE ENGAGE DRIVE” control work

together to engage the blade. Both devices must be activated before the blade will work.

Releasing the “OPERATOR PRESENCE” lever will disengage both the blade and the

“BLADE ENGAGE DRIVE” control.

STARTING THE ENGINE

See engine manufacturer’s recommendations for the type and amount of oil and fuel used.

Engine must be level to accurately check and fill oil. Do not overfill.

• Make sure unit is level, blade is disengaged, and transaxle in “NEUTRAL”

• Check spark plug wire, oil level, and fuel level.

• Check all electrical connections for build-up of debris.

• Move throttle control to “FAST”, or “CHOKE” if choke is needed.

• For recoil starting, turn ignition key to the “ON”

position and pull rope with a

single fluid motion. For electric starting, turn the key to the “START” position.

• Set engine throttle control to “FAST”. The throttle must be set in the fast position for

maximum performance.

STOPPING

• Bring the Walk Behind to a complete stop by releasing the “GROUND CONTROL”

lever (left).

• Disengage mower blade by releasing the “BLADE ENGEGE DRIVE” control (right).

• Reduce engine idle speed, and allow engine to run momentarily for cooling.

• Place transaxle in the “NEUTRAL” position.

• Turn the ignition key to “OFF” position.

BREAKING IN YOUR WALK BEHIND

• Start engine properly.

• Slowly engage blade control.

• Under supervision, allow blade to rotate and engine to idle for 5 minutes.

• Disengage blade.

• Shift through each gear. While in each gear engage the “GROUND CONTROL” lever

and travel 20 yards to ensure transaxle works properly.

BEGIN CUTTING

• Make sure area is clear of all bystanders.

• Make sure that all guards, belt guides, and the spark plug wire are properly attached.

• Start engine, set engine throttle control at maximum engine idle speed for best results.

• Allow engine to run a few moments and slowly engage blade.

• Move transaxle into low gear and activate “GROUND CONTROL” lever.

• Turning is done by rotating the handles left or right. This machine has significant

weight and may take more effort to turn than one may expect. Turning could take

practice.

BACKING UP

• Disengage blade.

• Check behind you for safety.

• Move transaxle into “REVERSE” position.

• Activate “GROUND CONTROL” lever.

IMPORTANT: This engine is not equipped with a spark arrester muffler. It is a violation of

California Public Resource Code Section 4442 to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land. Other states or federal areas may have similar laws.

TRANSPORTING

• Shut off engine.

• Secure in place while unit is being transported.

• Unit should be left in low gear to avoid any slight rolling.

SUGGESTED PRACTICES

• Always operate engine at full throttle when cutting to assure the best cutting

performance and proper discharge of material.

• If grass is wet, allow it to dry. Wet grass clumps will collect on the bottom of the

deck.

• Go slow when cutting dense areas. Some dense areas may need to be gone over

twice. Better results occur if the second cut is 90 degrees to the first cut.

BEFORE EACH SEASON

A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run

better and last longer.

• Replace the spark plug.

• Clean or replace the air filter.

• Check blades and belts for wear.

BEFORE EACH USE

• Check engine oil level. Do this twice to ensure an accurate reading.

• Check condition of air filter and clean or replace if necessary.

• Check blade operation.

• Check for loose fasteners.

• Check tires for proper inflation. See tires for maximum inflation.

- Rear tire valve stems are located on the inside of the wheel rim.

- Front tire valve stems should be turned to avoid contact with caster yoke.

DAILY MAINTENANCE

Make sure all nuts and bolts are tight and cotter pins and retainer springs are secure.

Keep blades sharp. Observe all safety precautions.

BLADE CARE AND SERVICE

For best results blades must be kept sharp. The blades can be sharpened with a few strokes of a

file or grinding wheel. Do Not attempt to sharpen blades while they are on the machine.

Important: Replace blades that have been damaged or deeply nicked.

Important: Check blade and spindle hardware on a regular basis to make sure nuts are

tight.

SAFETY AND OPERATIONAL DECALS

Replace decal immediately if damaged. Order by part number from Swisher.

20076--SWISHER FLAG DECAL

OD55--DANGER DECAL OD45--WARNING DECAL

OD83--RN1234 SHIFT DECAL 10749--REVERSE LOCK DECAL

20000--Commercial Pro Decal

OD99112--LARGE LOGO WHITE DECAL

OD99156--SMALL LOGO WHITE DECAL

19722-- Predator Talon LH Decal

19732-- Predator Talon RH Decal

DECALS NOT SHOWN

Item # Description Part # Item # Description Part #

1 Guard - Engine, Cover 19888* 10 Pad - Battery BATPAD

2 Guard - Engine, Right 19886* 11 Bolt - Serr Flange, 5/16-18 X 1 10548

3 Bolt - Serr Flange 5/16-18 X 3/4 NB596 12 Cover - Belt 19889*

4 Clip - Tinnerman 5/16-18 3706 13 Nut - Serr Flange 5/16-18 NB170

5 Guard - Engine, Left 19885* 14 Channel - Side, Right 19211*

6 Guard - Engine, Front 19884* 15 Channel - Side, Left 19212*

7 Strap - Tarp, 9" AS013 16 Clip - Nylon 1/2" NB683

8 Hook - Tarp Strap AS049 17 Bolt - Serr Flange, 5/16-18 X 2 1/4 NB622

9 Battery (Not Included) N/A 18 Mount - Handle Height Adjust 19214*

ASSEMBLY DETAIL

When ordering replacement parts

*USE PAINT CODE: TK=BLACK

Tip: Valve stems should be turned

to avoid contact with caster yoke.

ENGINE & PULLEY ASSEMBLY

Important: Spring

must be hooked in

Idler Arm as shown.

Install Transmission Cable

(Not Shown) in Idler Arm

before installing Idler Arm

to Motor Plate.

When ordering replacement parts

*USE PAINT CODE: TK=BLACK

NOT SHOWN

Description Part #

Harness - Wiring 19893

Wire - Alternator 19894

Item # Description Part #

1 Bolt - Serr Flange, 5/16-18 X1 1/4 NB253

2 Nut - Nyloc 5/16-18 NB181

3 Nut - Serr Flange 5/16-18 NB170

4 Bolt - Serr Flange, 5/16-18 X 1 10548

5 Screw - HX Tek 1/4 X 3/4 NB161

6 Solenoid - 3 Pole 1002004

7 Bolt - Serr Flange, 5/16-18 X 1 3/4 NB515

8 Weldment - Belt Retention 10767

9 Bolt - Serr Flange, 5/16-18 X 3/4 NB596

10 Spacer - Engine Pulley BB105S

11 Key Stock - 1/4 X 1/2 4258

12 Pulley - Engine, 2.5" 2411

13 Engine Pulley- 4.25"OD,1 1/4 ID BB105

14 Washer - Belleville 7/16 X 1 1/4 699

15 Nut - 2 Way Lock 3/8-16 NB280

16 Pulley - Idler, OD-2.16", ID-3/8" B27

17 Belt - Transmission, 35" 690

18 Washer - 1 X 1 1/2 NB614HT

19 Key Stock - 1/4 X 1 9031

20 Washer - .531IDX1 1/2OD TR150W

21 Bolt - HCF, 7/16-20 X 1 1/2 NB637

22 Engine B&S Recoil/12V St W/Gas Tank N/A

23 Valve - Oil Drain 16000

24 Nut - Serr Flange, 1/4-20 NB524

25 Plate - Motor Base 19213*

26 Washer - SAE Flat 3/8 NB272

27 Bolt - 3/8-16 X 1 1/2 NB107

28 Spring T2SM

29 Bolt - 1/4-20 X 3/4 NB250

30 Arm - Transmission Idler 10671*

31 Bushing - Idler 6037

32 Bolt - 3/8-16 X 1 NB604

Inhaltsverzeichnis

Andere Swisher Rasenmäher Handbücher

Swisher

Swisher T1260, T1360, T1460 Bedienungsanleitung

Swisher

Swisher FC1966BS Bedienungsanleitung

Swisher

Swisher ZT1436B, ZT18542, ZT2250 Bedienungsanleitung

Swisher

Swisher Predator WB924 Bedienungsanleitung

Swisher

Swisher FC18560BS Bedienungsanleitung

Swisher

Swisher POL11550 Bedienungsanleitung

Swisher

Swisher POSTMASTER PST67522 Bedienungsanleitung

Swisher

Swisher POL10544C Bedienungsanleitung

Swisher

Swisher T11544 Bedienungsanleitung

Swisher

Swisher QUADBOSS QBT14560A Bedienungsanleitung

Swisher

Swisher Commercial Pro Response Z21554CPHO Bedienungsanleitung

Swisher

Swisher FC11544BSXP Bedienungsanleitung

Swisher

Swisher FC14560BS Bedienungsanleitung

Swisher

Swisher FT1150 Bedienungsanleitung

Swisher

Swisher QUADBOSS QBFC14560 Bedienungsanleitung

Swisher

Swisher ZT2452A Bedienungsanleitung

Swisher

Swisher ZT2760B Bedienungsanleitung

Swisher

Swisher ST60022Q Bedienungsanleitung

Swisher

Swisher Trim-N-Mow Plus STS67522BS Bedienungsanleitung

Swisher

Swisher ZT2866A-CA Bedienungsanleitung

Swisher

Swisher ZT2452A-CA Bedienungsanleitung

Swisher

Swisher ZT2766 Bedienungsanleitung

Swisher

Swisher ZT13536, ZT17542B, ZT20050 Bedienungsanleitung

Swisher

Swisher COMMERCIAL PRO PREDATOR TALON Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung