Sylvac UL 4 Bedienungsanleitung

INSTRUCTIONS

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE D’USO

MODO DE EMPLEO

UL 4

Ultra-light caliper

Pied à coulisse ultra-léger

Extra-leichter Messschieber

Calibro a corsoio ultraleggero

Calibre ultraligero

Installing and replacing the battery

Mise en place et remplacement de la

batterie

Einbau und Austausch von Batterie

Installazione e sostituzione della batteria

Colocación y sustitución de la batería

No. 1

Battery / batterie / batterie / batteria / bateria: lithium 3V, type CR2477 or CR2032 (with adaptater)

CR2477

CR2032

Option to use a CR2032 battery with the adapter accommodated at the end of the main beam.

Possibilité d’utiliser une pile CR2032 avec l’adaptateur logé à l’extrémité de la perche.

Batterie CR2032 mit Adapter am Stangenende verwendbar.

Possibilità di utilizzare una pila CR2032 con l’adattatore alloggiato all’estremità dell’asta

Posibilidad de utilizar una batería CR2032 con el adaptador alojado en el extremo de la columna.

No. 7

or / ou / oder / o / o

Outline dimension drawing

Schéma d’encombrement

Masszeichnung

Disegno quotato

Planos dimensionales

202

103

262

124

8x30 h6

90 133 47.6

64.5

747 7 47

23.5 23.5

2x Ø4 F8 1x M4 1x M4 2x Ø4 F8

202

103

262

124

8x30 h6

90 133 47.6

64.5

747 7 47

23.5 23.5

2x Ø4 F8 1x M4 1x M4 2x Ø4 F8

MINMAX

PRESET

TOL INPUT

1. Left measurement jaw

2. Right measurement jaw

3. Measurement button

4. Left moving cursor locking lever

5. Right cursor clamp knob

6. Internal measurement plunger clamp knob

7. Pressure cursor

8. Pressure cursor locking lever

9. Pressure indicator

10. SET button

11. Favourites button

12. Mode button

13. Battery cover

14. Display

15. Internal interchangeables measurement plungers

16. Main beam

17. Proximity cable housing

4 14 5 10 8 7

13 12 11 9

Pressure indicator

Middle position

Measuring position

(external measurement)

Measuring position

(internal measurement)

MAX

PRE PUT

TOL

MIN

SET IN

1. Measurement unit (mm/INCH)

2. + / - indicator

3. Low battery

4. Active tolerance mode

5. Button locking

6. Preset mode

7. Multiplication factor

8. 6-digit display

9. Freeze measurement value

10. Bluetooth® connection

11. Send data

12. MIN / MAX / DELTA mode

13. Internal/external measurement indicator

14. Active reference indicator

15. Tolerance indicator

14 13 12 11

7654

1. Operating features of the instrument

- The instrument has two operating modes: basic functions (direct ac-

cess) and advanced functions. In addition to the conguration functions,

available access to the MIN, MAX and DELTA (TIR) mode, or display of

tolerances (see chaps. 3 and 4)

- The «favourite» key gives direct access to the function used most often

(see chap. 7)

- Sets a Preset value, reset the MIN/MAX mode, veries a selection, and

controls switching off the instrument. By default, SIS mode enables au-

tomatic switch-off with no loss of origin (see chap. 8).

1.1 Personalising the functions

It is possible to activate or de-activate certain functions of the instrument via

RS232 (see chap. 11)

1.2 Data transmission parameters

4800Bds, 7 bits, even parity, 2 stop bits

2. Start

Press a button.

SET

MODE

3. Basic functions

MODE

SET

Each short press on gives direct access to the basic functions:

→ Units selection (mm or Inch)

→ Choice of reference (REF1, REF2 or

automatic REF)

→ Inputting a Preset value

next digit 0...9 save the

Preset

MODE

SET

MODE

SET

MODE

ArEf

sEt 0.00 → Normal mode : zero reset

Min (max) Mode : diameter calibration on the

measured min (max) value.

4. Advanced functions

MODE

Prolonged pressure (>2s) on gives access to the advanced functions.

Then, each short press on accesses the required function:

MODE

SET

MODE

SET

MODE

SET

MODE

MINIMUM, MAXIMUM mea-

surement and DELTA (TIR)

.................Tolerance display

(inputting tolerance limits, see chap. 6)

.................Choice of measurement direction

(positive or negative sense)

save the

Preset

3.1 Automatic references

The instrument has the ability to switch automatically between its two references.

This allows using the caliper for both internal and external measuring without

going through the menu to change the reference.

Steps :

On Ref 1

• Introduce a measurement standard as preset, measure this standard and

do a preset recall

• Or set the zero at closed jaws position

On Ref 2

• Measure the internal measurement probes gap (with a caliper, probes

included) and introduce it as preset value

• Do a preset recall at closed jaws position

Set AREF

It is now possible to measure in REF1 when closing the jaws or in REF2 when

opening the jaws.

4. Advanced functions (continuation)

SET

MODE

SET

MODE

SET

MODE

SET

MODE

SET

MODE

Introduction of a multiplier, other than 1.000

next digit 0...9 save the multiplier

Keypad lock : only the favourite key remains active

(to unlock the keypad, press for 5 s.)

SET

MODE

MACrEsEt

Bluetooth

® function

The connection procedure has been designed to be simple and is signalled by

the following three states:

1° Symbol off disconnected mode

2° Symbol blinking advertising mode

3° Symbol on connected mode

Connection:

1°Activate

Bluetooth

® Smart compatible software and hardware (Master : PC,

Display Unit)

2°Start the instrument. By default the

Bluetooth®

module is active and the

instrument is available for connection during 120s (advertising mode)

3°As soon as the device is detected, a connection is established automatical-

ly. If no connnection is established during 120s, reactivate the

Bluetooth

module using the bt / On menu.

4°Instrument is ready to communicate (connected mode)

5. Bluetooth®

5.1 Pairing

Pairing with master is automatically done at rst connection.

To connect the instrument to a new master (new pairing), it is necessary to

clear all pairing information on the instrument using the bt / rESEt menu.

Automatic switch-off mode

MAn = de-activated, Auto = active (after 20 min.)

Introduction of a multiplier, other than 1.000

next digit 0...9 save the multiplier

Keypad lock : only the favourite key remains active

(to unlock the keypad, press for 5 s.)

Bluetooth

® function

6. Insert tolerance limits

MODE

SET

In order to introduce or modify the tolerance limits, it is necessary to select tol →

On , followed by a short press on

Note :

- In case of measuring internal ratings, you can cross the indicators by reversing

the order of entering the tolerance intervals (upper interval < lower interval)

- It is possible to introduce different tolerance limits on REF1 and REF2.

- It is also possible to display the tolerance limits when the instrument is working

in MIN, MAX or DELTA (TIR) mode

....... Input the lower tolerance limit (e.g. +0019.90 for 20-0.1mm)

.......Input the upper tolerance limit (e.g. +0020.10 for 20+0.1mm)

next digit 0...9 save the tolerance

5.2

Bluetooth

® specication

Radio frequency 2.4Ghz

Robustness FHSS

Latency (from not connected state to

send data) <6ms

Range Open space : up to 15m

Industrial environment : 1-5m

Autonomy with CR2477

Continuous : up to 8 months (Always connected with 4 values /sec)

Saver : up to 21 months (The instrument sends value only when the position has changed)

Blind/Push : up to 24 months (Value is sent from the instrument (button) or requested from

the computer)

Other specications on the manufacturer’s website

The «favourite» key gives direct access to a predened function, and can be

congured according to the needs of the user.

In order to assign a function to the «favourite» key, give a prolonged press on

and then select the required function:

Validation of selection: By a prolonged press on , or a press on or

Note: a function can also be assigned via RS232 using the command <FCT

+ Function No.> / example : Change of Unit = <FCT4>

7. Favourite key

10 dir

9 rES

8 toL

7 ModE

6 PrE

4 Unit

3 SEt

2 CLr

1 HoLd

0 dAtA Data transmission

(default)

Hold display

Re-initialise Min-

Max-Delta

Zero reset

Diameter calibration

(min.-max. mode)

mm – IN

Recall Preset

Nor–Min–Max-Delta

Tol ON–Tol OFF

Measurement

sense, positive -

negative

Multiplier

Bluetooth®

10 dir

9 rES

8 toL

7 ModE

6 PrE

4 Unit

3 SEt

2 CLr

1 HoLd

0 dAtA

11 Mul

12 bt

8. Adjustment of the measuring system

MODE

SET

Certain applications need to adjust the instrument to the MIN (or MAX) measured

value. In this case, proceed as follows :

8.1 Adjustment of the instrument

• Enter a Preset value corresponding to the actual size of the standard (see

chap. 3)

• Select the MIN mode (or MAX, depending on the application) (see chap. 4)

• Make a standard measurement (going through the turnaround point)

• Adjust the instrument by selecting the SEt mode and pressing on the button

(see chap. 3)

• The instrument is adjusted and ready to measure.

8.2 Measure

• Make the measurements. The digital display stores and displays the MIN

(or MAX) measured value.

• Before each new measurement, reset the measured value by a short press

SET

Andere Handbücher für UL 4

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Sylvac Messgerät Handbücher

Sylvac

Sylvac S Dial WORK Smart Bedienungsanleitung

Sylvac

Sylvac SYLVAC-SCAN S145 XL Bedienungsanleitung

Sylvac

Sylvac PS16 V2 Bedienungsanleitung

Sylvac

Sylvac D104-PC Bedienungsanleitung

Sylvac

Sylvac SCAN 52 Bedienungsanleitung

Sylvac

Sylvac S Cal EVO Standard Bedienungsanleitung

Sylvac

Sylvac S_Cal EVO Bedienungsanleitung

Sylvac

Sylvac S_Dial WORK ANALOG Smart Bedienungsanleitung

Sylvac

Sylvac S Mike IP67 Bedienungsanleitung

Sylvac

Sylvac SCAN F60 Bedienungsanleitung

Sylvac

Sylvac EVO Bluetooth Bedienungsanleitung

Sylvac

Sylvac S Mike PRO Smart Bedienungsanleitung

Sylvac

Sylvac Scan Series Bedienungsanleitung

Sylvac

Sylvac S Dial WORK Bedienungsanleitung

Sylvac

Sylvac S25 Bedienungsanleitung

Sylvac

Sylvac S Dial Mini Bedienungsanleitung

Sylvac

Sylvac UL 4 Bedienungsanleitung

Sylvac

Sylvac Hi Gage ONE Smart Bedienungsanleitung

Sylvac

Sylvac S Dial WORK ANALOG NANO Smart Bedienungsanleitung

Sylvac

Sylvac Hi Cal Bedienungsanleitung

Sylvac

Sylvac SYLVAC-SCAN S145 Bedienungsanleitung

Sylvac

Sylvac 810.9707 Bedienungsanleitung

Sylvac

Sylvac SCAN F60 Bedienungsanleitung

Sylvac

Sylvac Bowers XTL Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung