Sylvac UL 4 Bedienungsanleitung
1
E
INSTRUCTIONS
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE D’USO
MODO DE EMPLEO
E
F
D
UL 4
Ultra-light caliper module
Module pied à coulisse ultra-léger
Extra-leichter Messschieber Modul
Modulo calibro a corsoio ultraleggero
Módulo calibre ultraligero
I
S
2
Installing and replacing the battery
Mise en place et remplacement de la
batterie
Einbau und Austausch von Batterie
Installazione e sostituzione della batteria
Colocación y sustitución de la batería
Battery / batterie / batterie / batteria / bateria: lithium 3V, type CR2477 or CR2032 (with adapter, except ULD4)
CR2477
CR2032
Option to use a CR2032 battery with the adapter.
Possibilité d’utiliser une pile CR2032 avec l’adaptateur.
Batterie CR2032 mit Adapter.
Possibilità di utilizzare una pila CR2032 con l’adattatore.
Posibilidad de utilizar una batería CR2032 con el adaptador.
+
No. 7
or / ou / oder / o / o
No. 1
Adapter for CR2032 (except ULD4)
3
E
Outline dimension drawing
Schéma d’encombrement
Masszeichnung
Disegno quotato
Planos dimensionales
4
5
E
1. SET button
2. Favourites button
3. MODE button
4. Battery cover
5. Display
6. Proximity cable housing
1. Measurement unit (mm/INCH)
2. + / - indicator
3. Low battery
4. Active tolerance mode
5. Button locking
6. Preset mode
7. Multiplication factor
8. 6 1/2 digits display
9. Freeze measurement value
10. Bluetooth® connection
11. Send data
12. MIN / MAX / DELTA mode
13. Internal/external measurement indicator
14. Active reference indicator
15. Tolerance indicator
Description of the module
5 6 1
2
34
14 13 12 11
10
9
8
7654
3
2
1
15
6
1. Operating features of the instrument
- The instrument has two operating modes: rst level functions (direct
access) and second level functions. (see chaps. 3 and 4)
- The «favourite» key gives direct access to one of the most used func-
tions (see chap. 5)
- Sets a Preset value, reset the MIN/MAX mode, applies a selection and
controls switching off the instrument. By default, SIS mode enables au-
tomatic switch-off without any loss of origin (see chap. 7).
1.1 Personalising the functions
It is possible to activate or de-activate some functions of the instrument (see
chap. 9)
1.2 Data transmission parameters
4800Bds, 7 bits, even parity, 2 stop bits
2. Start
Press any button.
SET
MODE
7
E
3. First level functions
MODE
MODE
SET
Each short press on gives direct access to the rst level functions :
Normal mode : zero reset
Mode int-ext : preset on the measured min or max value
SEt
rEF
PrE
ModE
IntE
toL
bt
Not enabled by default, except in IntE
Choice of reference (REF1, REF2 or automatic REF, see chap. 3.1 Auto ref)
Introduction of a Preset value next digit 0...9 save the Preset
MINIMUM, MAXIMUM and DELTA (TIR) measurement
Tolerance display (introduction of tolerance limits, see chap. 3.2)
Dynamic preset (see chap. 6)
Bluetooth®
function (see chap. 3.3)
rESEt
AMAxAMin
MAC
SET
MODE
MODE
MODE
MODE
MODE
MODE
MODE
Auto
sEt
0.00
SET
SET
IntE
bt
SET
SET
1)
1) not available with Simple prole
8
3.1 Automatic references
The instrument has the ability to switch automatically between its two references.
This allows using the caliper for both internal and external measuring without
going through the menu to change the reference.
Steps :
On Ref 1
• Introduce a measurement standard as preset, measure this standard and
do a preset recall
• Or set the zero at closed jaws position
On Ref 2
• Measure the internal measurement probes gap (with a caliper, probes
included) and introduce it as preset value
• Do a preset recall at closed jaws position
Set Auto
It is now possible to measure in REF1 when closing the jaws or in REF2 when
opening the jaws.
Remark: for the reference change to work, it is necessary to make a displacement
>0.2mm in the opposite direction.
3.2. Insert tolerance limits
MODE
MODE
SET
In order to introduce or modify the tolerance limits, it is necessary to select tol →
On , followed by a short press on
....... Input the lower tolerance limit (e.g. +0019.90 for 20-0.1mm)
.......Input the upper tolerance limit (e.g. +0020.10 for 20+0.1mm)
next digit 0...9 save the tolerance
9
E
The connection procedure has been designed to be simple and is signalled by
the following three states:
1° Symbol off................disconnected mode.
2° Symbol blinking .......advertising mode.
3° Symbol on .............. connected mode.
3.3. Bluetooth® conguration
The following options can be selected to control the Bluetooth®module.
On Enable Bluetooth®module (start advertising mode).
OFF Disable Bluetooth®module (terminate active connection).
rESEt Clear pairing information.
MAC Display the MAC (Media Access Control) address.
Three Bluetooth® proles are available.
SIMPLE Prole without pairing (default).
PAIr Paired and secured prole.
HId Virtual keyboard mode (compatible with recent equipement without
driver installation).
Note:
Pairing information are erased while prole is switched.
Note :
- In case of internal measurements, you can cross the indicators by reversing
the order of entering the tolerance intervals (upper interval < lower interval)
- It is possible to introduce different tolerance limits on REF1 and REF2.
- It is also possible to display the tolerance limits when the instrument is working
in MIN, MAX or DELTA (TIR) mode
....... Input the lower tolerance limit (e.g. +0019.90 for 20-0.1mm)
.......Input the upper tolerance limit (e.g. +0020.10 for 20+0.1mm)
next digit 0...9 save the tolerance
10
3.3.1
Bluetooth
® specication
Frequency Band 2.4GHz (2.402 - 2.480GHz)
Modulation GFSK (Gaussian Frequency Shift Keying)
Max Output Power Class 3: 1mW (0dBm)
Range Open space: up to 15m
Industrial environment: 1-5m
Battery life with CR2477
Continuous : up to 8 months - Always connected with 4 values /sec.
Saver : up to 21 months - The instrument sends value only when the position has changed.
Blind/Push : up to 24 months - Value is sent from the instrument (button) or requested
from the computer.
Other specications on the manufacturer’s website
Connection:
1° Activate Bluetooth®compatible software and hardware (Master : PC,
Display Unit).
2° Start the instrument. By default the Bluetooth®module is active and
the instrument is available for connection (advertising mode).
3° If no connnection is established during the advertisement period, rea-
ctivate the Bluetooth®module using the bt /On menu.
4° Instrument is ready to communicate (connected mode.)
Only with paired prole :
Pairing with master is automatically done at rst connection.
To connect the instrument to a new master (new pairing), pairing information on
the instrument must be cleared using the bt / rESEt menu.
Andere Handbücher für UL 4
1
Inhaltsverzeichnis
Sprachen:
Andere Sylvac Messgerät Handbücher
Sylvac
Sylvac Scan Series Bedienungsanleitung
Sylvac
Sylvac PS15 Bedienungsanleitung
Sylvac
Sylvac Bowers XTL Bedienungsanleitung
Sylvac
Sylvac S Depth PRO Bedienungsanleitung
Sylvac
Sylvac PS16 V2 Bedienungsanleitung
Sylvac
Sylvac S Dial WORK Smart Bedienungsanleitung
Sylvac
Sylvac D104-PC Bedienungsanleitung
Sylvac
Sylvac SCAN 52 Bedienungsanleitung
Sylvac
Sylvac Hi Cal 150 Bedienungsanleitung
Sylvac
Sylvac S_Cal EVO Bedienungsanleitung
Sylvac
Sylvac S_Dial WORK ANALOG Smart Bedienungsanleitung
Sylvac
Sylvac S-Mike PRO Bedienungsanleitung
Sylvac
Sylvac S Dial Mini Bedienungsanleitung
Sylvac
Sylvac S Dial WORK Bedienungsanleitung
Sylvac
Sylvac 810.9707 Bedienungsanleitung
Sylvac
Sylvac S_Cal EVO Smart Form E Bedienungsanleitung
Sylvac
Sylvac EVO Bluetooth Bedienungsanleitung
Sylvac
Sylvac SYLVAC-VISIO 300 GL Bedienungsanleitung
Sylvac
Sylvac S Mike EVO Bedienungsanleitung
Sylvac
Sylvac Hi Gage ONE Smart Bedienungsanleitung
