Teledyne Lecroy ZS Series Bedienungsanleitung

Operator’s

Manual

Series

High

-Impedance

Active Probe

ZS1000, ZS1500, ZS2500

High-Impedance Active Probes

Operator’s Manual

April, 2017

ZS Series High-Impedance Active Probes Operator’s Manual

Unauthorized duplication of Teledyne LeCroy documentation materials other

than for internal sales and distribution purposes is strictly prohibited.

However, clients are encouraged to distribute and duplicate Teledyne LeCroy

documentation for their own internal educational purposes.

Teledyne LeCroy is a registered trademark of Teledyne LeCroy, Inc. Windows

is a registered trademark of Microsoft Corporation. Other product or brand

names are trademarks or requested trademarks of their respective holders.

Information in this publication supersedes all earlier versions. Specifications

are subject to change without notice.

928327-00 Rev A

April 2017

Operator’s Manual

Warranty

Teledyne Lecroy warrants this oscilloscope accessory for normal use and

operation within specification for a period of one year from the date of

shipment. Spare parts, replacement parts and repairs are warranted for 90

days.

In exercising its warranty, Teledyne LeCroy, at its option, will either repair or

replace any assembly returned within its warranty period to the Customer

Service Department or an authorized service center. However, this will be

done only if the product is determined by Teledyne LeCroy’s examination to be

defective due to workmanship or materials, and the defect is not caused by

misuse, neglect, accident, abnormal conditions of operation, or damage

resulting from attempted repair or modifications by a non-authorized service

facility.

The customer will be responsible for the transportation and insurance

charges for the return of products to the service facility. Teledyne LeCroy will

return all products under warranty with transportation charges prepaid.

This warranty replaces all other warranties, expressed or implied, including

but not limited to any implied warranty of merchantability, fitness or adequacy

for any particular purposes or use. Teledyne LeCroy shall not be liable for any

special, incidental, or consequential damages, whether in contract or

otherwise.

ZS Series High-Impedance, Active Probes

Table of Contents

Safety Instructions ................................................................................1

Introduction...........................................................................................2

Standard Accessories............................................................................3

Tips ......................................................................................................... 4

Grounds .................................................................................................. 5

Leads ...................................................................................................... 6

Clips and Grabbers ................................................................................ 6

Probe Holder .......................................................................................... 7

Probe Impedance and Equivalent Circuits .......................................... 8

Probe Operation ..................................................................................10

Handling the Probe.............................................................................. 10

Connecting the Probe to the Test Circuit .......................................... 10

Connecting the Probe to an Oscilloscope ......................................... 10

Operation with a Teledyne LeCroy Oscilloscope............................... 11

Auto Zero.............................................................................................. 11

High Frequency Measurements ......................................................... 12

Care and Maintenance .........................................................................16

Cleaning................................................................................................ 16

Calibration Interval .............................................................................. 16

Service Strategy................................................................................... 16

Replacement Parts.............................................................................. 16

Performance Verification.....................................................................17

Required Test Equipment ................................................................... 17

Test Setup and Preliminary Procedure .............................................. 19

Functional Check................................................................................. 19

Verification Procedure ........................................................................ 20

ZS Series Probe Test Record.............................................................. 24

Reference Material ..............................................................................25

Operator’s Manual

Safety Instructions

Observe generally accepted safety procedures in addition to the precautions

listed here. The overall safety of any system incorporating this accessory is

the responsibility of the assembler of the system.

Symbols

These symbols appear on the probe body or in documentation to alert you to

important safety considerations.

CAUTION of potential for damage to equipment, or WARNING of

potential for bodily injury. Attend to the information, and do not

proceed until conditions are fully understood and met.

ELECTROSTATIC DISCHARGE (ESD) HAZARD. The probe is

susceptible to damage if anti-static measures are not taken.

Precautions

Connect and disconnect properly. Connect probe to the measurement

instrument before connecting the test leads to a circuit/signal being tested.

Use only within operational environment listed. Do not use in wet or

explosive atmospheres.

Use indoors only.

Keep product surfaces clean and dry.

Be careful with sharp tips. The tips may cause bodily injury if not handled

properly.

Use only accessories designed for use with the product.

Observe all terminal ratings. To avoid electric shock or probe damage, do not

use the probe above the input limits shown on the probe.

Do not excessively bend cables.

Do not operate with suspected failures. Do not use the probe if any part is

damaged. Cease operation immediately and secure the probe from

inadvertent use.

ZS Series High-Impedance, Active Probes

Operating Environment

The accessory is intended for indoor use and should be operated in a clean,

dry environment. Before using this product, ensure that its operating

environment is maintained within these parameters:

Temperature: 0 to 40° C

Humidity: Maximum relative humidity 80 % for temperatures up to 31 °C

decreasing linearly to 50 % relative humidity at 40° C

Altitude: Up to 10,000 ft (3,048 m)

Introduction

The ZS Series (ZS1000, ZS1500, and ZS2500) are a small, high-impedance

active probes designed to meet today’s increasing demand for

measurements on a variety of test points. With low input capacitance and

high input resistance, circuit loading is minimized.

The ZS probes can be used with a variety of Teledyne LeCroy oscilloscopes

with MAUI firmware version 6.5.0.5 or later (see the product page at

teledynelecroy.com/oscilloscope for compatibility). With the ProBus

interface, the probe becomes an integral part of the oscilloscope, controlled

from the oscilloscope’s front panel. The oscilloscope provides power to the

probe, so there is no need for a separate power supply or batteries.

See the ZS product page at teledynelecroy.com for probe specifications.

Key Benefits

Features

High frequency performance

Low input capacitance

Wide dynamic range

ProBus interface

Small, low mass probe head is designed

for ease of use and high performance.

Probe tip socket fits easily onto 0.025

inch square pins for direct access to

test points. Several available adaptors

connect directly to the probe socket.

Ground socket accepts several different

ground leads to provide a short ground

path for high frequency performance.

Operator’s Manual

Standard Accessories

ZS Series probes are shipped with the following standard accessories:

Standard Accessory

QTY

Replacement Part Number

Straight Pin Lead – Short

PK-ZS-003

Straight Pin Lead – Long

PK-ZS-004

Right Angle Lead – Short

PACC-LD003

Right Angle Lead – Long

PACC-LD004

Y Lead Adapter

PK-ZS-005

Micro-Grabber Pair

PK-ZS-007R and PK-ZS-007B

Ground Blade – Wide

PK-ZS-011

Probe Tip – Standard

PK-ZS-001

Right Angle Socket

PK-ZS-006

Offset Ground – Z Lead

PK-ZS-002

Ground Blade – Narrow

PK-ZS-008

Copper Tape

PK-ZS-009

Pogo Tip

PK-ZS-013

2.54mm Square Pin Adapter

PK-ZS-012

Channel ID Clips (1 set of 4)

PK-ZS-010

Freehand Probe Holder

PACC-MS005

Bent Tip

PACC-PT005

IC Tip

PACC-PT003

Pogo Ground Lead

PACC-CD008

Operator’s Manual

N/A*

Certificate of Calibration

ZS-CC

* PDF copy of this manual available free at teledynelecroy.com/support/techlib.

ZS Series High-Impedance, Active Probes

Tips

Straight Tip

The straight tip is rugged and designed for

general probing. Fits in either probe socket.

IC Lead Tip

The IC Lead Tip is covered in insulation on all

des (except for a small edge). This tip was

designed to prevent shorting neighboring IC

leads. The gold part of the tip is not insulated and

should touch the IC lead to be tested. It is one

size

-fits-all and will work with any IC lead pitch.

Fits in either probe socket.

Bent Tip

The Bent Tip is made out of titanium, this tip is

ideal for situations that require

you to hold the

probe parallel to the circuit board under test. Also

gives you more control when holding the probe

like a pencil. Fits in either probe socket.

Pogo Tip

The pogo tip provides z-axis compliance. The tip

can fit into a socket or onto a

n IC leg.

Discrete SMD Tip

The crescent shape of this tip is designed to fit

tightly on capacitors, resistors, transistors and

other surface mount components with discrete

leads. Fits in either probe socket

2.54mm Square Pin Adapter

2.54 mm Square Pin Adapter. The 2.54 mm

square pin adapter fits into both the

input and

ground lead of the ZS probe for easy connection

to standard 2.54 mm square pin spacing on a

circuit board.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Lecroy Messgerät Handbücher

Teledyne Lecroy

Teledyne Lecroy WavePulser 40iX Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook DL02-HCM Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ZD500 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy DL03-ISO Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Summit T416 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy M42de Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook DL05-HCM Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PCI Express 2.0 Mid-Bus Probe Einrichtungshandbuch

Teledyne Lecroy

Teledyne Lecroy PP016 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP006C Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ADP300 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline 802.11 Montageanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook Frontline X500 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy SierraNet M328 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveMaster 8000HD Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP006D Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy M21 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline NFC-F Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy AP033 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy WaveRunner 8000-R Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy BPA Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVFO103 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP2060 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung