Teledyne Lecroy WaveRunner 8000-R Bedienungsanleitung

WaveRunner 8000-R

Oscilloscopes

Getting Started Guide

930948-00 Rev A

WaveRunner 8000-R Oscilloscopes

Getting Started Guide

Unauthorized duplication of Teledyne LeCroy documentation materials is strictly prohibited. Customers are permitted to

duplicate and distribute Teledyne LeCroy documentation for internal educational purposes.

Teledyne LeCroy is a trademark of Teledyne LeCroy, Inc. Other product or brand names are trademarks or requested

trademarks of their respective holders. Information in this publication supersedes all earlier versions. Specifications are

subject to change without notice.

930948-00 Rev A,

March, 2019

700 Chestnut Ridge Road

Chestnut Ridge, NY 10977

1.800.5.LECROY •teledynelecroy.com

WaveRunner 8000-R Getting Started Guidel 1

Welcome

Thank you for buying a Teledyne LeCroy product. We’re certain you’ll be

pleased with the detailed features unique to our instruments.

This guide is intended to help you install a WaveRunner 8000-R

oscilloscope into your test environment and prepare it for remote control.

See the MAUI Oscilloscopes Remote Control and Automation Manual for

comprehensive information on remote control of Teledyne LeCroy MAUI

oscilloscopes.

See the WaveRunner 8000 Operator’s Manual for information on the

operational features of the WaveRunner 8000-R, many of which can be

controlled remotely using either traditional IEEE 488.2 commands or

Windows® COM Automation.

Both manuals can be downloaded from the Oscilloscope Manuals page

on our website at:

teledynelecroy.com/support/techlib

Contents

Introducing WaveRunner 8000-R 2

Key Specifications 2

Safety 2

Front of Oscilloscope 4

Back of Oscilloscope 5

Powering On/Off 6

Presets 6

Preparing for Remote Control 6

Remote Configuration 8

Rackmounting 10

Cleaning 12

Calibration 12

Firmware Updates 12

Service 13

Certifications 14

Warranty 16

930948-00 Rev A

Key Specifications

Detailed specifications are maintained on the product page at

teledynelecroy.com.

INTRODUCTION

WR8104-R WR8254M-R WR8404M-R

Bandwidth 1 GHz 2.5 GHz 4 GHz

Analog Channels 4 standard or 2 interleaved

Max. Memory 32 Mpts 128 Mpts 128 Mpts

Max. Sample Rate 20 GS/s 40 GS/s 40 GS/s

Vertical Resolution 8-bit 8-bit 8-bit

Introducing WaveRunner 8000-R

WaveRunner 8000-R oscilloscopes utilize the WaveRunner 8000

acquisition system to provide a high-performance, 4 GHz oscilloscope in

a convenient, low-profile form factor.

The compact design has a height of less than 2U (3.5”, 8.89 cm) and

includes a standard rackmount kit, easily lending itself to be installed in

an automated test environment.

Unlike most digitizing systems, the WaveRunner 8000-R provides

the powerful, deep toolbox that is expected in a Teledyne LeCroy

oscilloscope. The full range of the WaveRunner 8000’s analysis capability

is available; including an array of serial protocol analysis packages and

application specific packages.

The WaveRunner 8000-R models are fully software-compatible with their

WaveRunner 8000 counterparts. Development can be conducted with the

assistance of the front panel and display of the WaveRunner 8000, then

seamlessly transitioned to automated testing.

A variety of remote connectivity options—LAN, USBTMC, and GPIB (with

optional adapter)—offer flexibility when connecting to the WaveRunner

8000-R. Teledyne LeCroy’s free WaveStudio software is a fast and easy

way to analyze acquired waveforms off-line, or remotely control an

oscilloscope from your desktop. CAUTION of potential damage

to equipment, or WARNING of

potential bodily injury. Refer to

manual. Do not proceed until the

information is fully understood

and conditions are met.

WARNING. Risk of electric shock

or burn.

Frame or chassis terminal

Alternating current

Power On

Standby Power

Safety

Observe generally accepted safety practices in addition to the precautions

specified here.

Symbols

WaveRunner 8000-R Getting Started Guidel 3

SAFETY

WR8104-R WR8254M-R, WR8404M-R

AC Power 100-240 VAC (±10%) at 50/60 Hz (±10%) or

100-120 VAC (±10%) at 400 Hz (±5%)

Automatic AC Voltage Selection

Consumption

Nominal

240 W / 240 VA

340 W / 340 VA

Maximum* 320 W / 320 VA 420 W / 420 VA

Standby 6 W 6 W

Power

* All PC peripherals and active probes connected to four channels.

Operating Environment Precautions

Use proper power cord. Use only the power cord shipped with this

instrument and certified for the country of use.

Maintain ground.

The AC inlet ground is connected to the frame of the

instrument. Connect line cords only to outlets with safety ground contacts.

WARNING. Interrupting the protective conductor inside or outside

the oscilloscope, or disconnecting the safety ground terminal,

creates a hazardous situation. Intentional interruption is prohibited.

Connect and disconnect properly. Do not connect/disconnect probes or

test leads while they are connected to a live voltage source.

Observe all terminal ratings. Do not apply a voltage to any input that

exceeds the maximum rating of that input. Refer to the markings next to

the BNC terminals for maximum allowed values.

Use only within operational environment listed. Do not use in wet or

explosive environments.

Use indoors only.

Keep product surfaces clean and dry.

Do not block the cooling vents. Leave a minimum six-inch (15 cm) gap

between the instrument and the nearest object. Keep the underside clear

of papers and other objects.

Exercise care when lifting and carrying.

Do not remove the covers or inside parts. Refer all maintenance to

qualified service personnel.

Do not operate with suspected failures. Check body and cables regularly.

If any part is damaged, cease operation immediately and sequester the

instrument from inadvertent use.

Temperature 0 °C to 40 °C

Humidity Maximum RH 80% (non-condensing) up to 30 °C

decreasing linearly to RH 50% at 40 °C

Altitude Up to 10,000 ft (3,048 m) at or below 30 °C

Measuring Terminal Ratings

Ratings apply to inputs C1-C4 and Ext In.

Measuring terminals have no rated measurement category (CAT) per IEC/EN 61010-1:2010.

Measuring terminals are not intended to be connected directly to supply mains.

Maximum Input Voltage 50 Ω coupling ≤ 5 Vrms

1 MΩ coupling ≤ 400 Vpk max. (Peak AC ≤ 10 kHz + DC)

derating at 14 dB/decade from 10 kHz to 2 MHz,

10 Vpk max. above 2 MHz

930948-00 Rev A

Front of Oscilloscope

OVERVIEW

A. Power On/Standby Switch

B. Remote Status Indicator

C. Analog Inputs C1-C4

D. External Trigger Input

E. USB 2.0 Port

F. Auxilliary (AUX) Output

G. Calibration Output Terminal

H. LBUS Port (reserved)

I. Ground Terminal

CD E

G H I

WaveRunner 8000-R Getting Started Guidel 5

Back of Oscilloscope

A. AC Power Inlet

B. USBTMC Port

C. External Reference Clock

Input (REF In) and Output (REF Out)

D. Removable Hard Drive

OVERVIEW

E. USB 2.0 Ports (2)

F. USB 3.1 Gen1 Ports (2)

G. DisplayPort Video Output

H. VGA Video Output

I. Ethernet Ports (2)

G H I

930948-00 Rev A

BASICS

Preparing for Remote Control

Powering On/Off

CAUTION: Connect only to grounded AC power. Be mindful of the

total power consumption, as connecting too many devices to a

single outlet can cause an overvoltage condition.

To power on, flip the Power Switch to ON. This automatically loads the

oscilloscope application.

The Remote Status Indicator on the front will flash when the oscilloscope

software is fully loaded and ready for remote control. It will remain a

steady green when a remote connection is established.

To power down, flip the Power Switch to STANDBY. When in Standby

mode, some "housekeeping" circuitry continues to draw power. The only

way to fully power down the instrument is to unplug the AC line cord from

the outlet. We recommend unplugging the instrument if it will remain

unused for a long period of time.

The WaveRunner 8000-R reverts to these factory defaults whenever

restarted after powering down:

Coupling 1 MOhm

Vertical Scale 1 V/div

Active Channels 4 (no interleaving)

Timebase 50 ns/div

Sampling Mode Real Time

Trigger Mode Stop

Network Addressing DHCP

Presets

The remote control setting is one of the few that do not revert to the

factory defaults when restarted, as it is critical to know what the setting is

in order to connect.

The factory default setting is LXI (VXI11), but the instrument will reboot

with whatever setting was last made.

We recommend that the remote control setting and the device address be

set locally at installation, prior to rackmounting, and that it not be changed

over a remote connection.

Remote Control Software

For all methods of remote control, an installation of NI-VISA is required on

the controller.

If you switch to TCPIP (VICP) remote control, also install the Teledyne

LeCroy VICP Passport for NI-VISA.

If the controller runs Windows, we recommend an installation of the free

Teledyne LeCroy WaveStudio software. WaveStudio will help you establish

and test the remote connection.

Teledyne LeCroy software is available from teledynelecroy.com/support/

softwaredownload under Oscilloscope Downloads > Software Utilities.

Initial Test Connection

Before rackmounting the WaveRunner 8000-R, we recommend making a

test connection from a PC to the oscilloscope using the default settings

to conrm that remote control is functional. This same procedure can be

used to test the remote connection after you have completed your remote

control conguration on the WaveRunner 8000-R, substituting whatever

connection type you have selected.

WaveRunner 8000-R Getting Started Guidel 7

5. Expand the list of WaveRunner 8000-R functions in the WaveStudio

Devices pane and open the Terminal window.

6. In the top pane of the Terminal, enter the query: *IDN?

If the WaveRunner 8000-R responds with its identifying information,

remote control is functional.

7. Open Display Capture.

An image of the WaveRunner 8000-R touch screen should appear in

the WaveStudio window.

8. Clicking on the image of the WaveRunner 8000-R in WaveStudio,

choose Utilities > Utilities Setup and open the Remote dialog.

The Remote dialog will show any dynamic IP address pulled.

BASICS

1. Install WaveStudio and NI-VISA on the PC. Open any firewalls between

the PC and the oscilloscope to TCP/IP communications on port 111.

2. Power on the WaveRunner 8000-R and connect to a network access

point using a standard Ethernet cable. It is helpful if the network is

served by a DHCP server, as this will allow you to test addressing.

3. On the PC, open WaveStudio and select Add Scope.

4. On the Add Scope dialog, choose connection type LXI and enter the

host name (oscilloscope serial number printed on the rear). Click OK.

If the connection is successful, after a brief pause you will see the

WaveRunner 8000-R added to the list of devices with the status “Alive.”

930948-00 Rev A

BASICS

When you are ready to make your actual remote conguration, connect a

monitor to either the DisplayPort or VGA video output, and a mouse and

keyboard to any of the USB ports. You can do this before or after powering

on the WaveRunner 8000-R. This will enable you to access both the MAUI

oscilloscope software and the Windows dialogs to make all the required

remote control settings. MAUI will appear on the external monitor as soon

as it is connected to the WaveRunner 8000-R.

Connecting via LAN

The WaveRunner 8000-R can be addressed using either the host name

or the IP address. We have found that using the full IP address is more

reliable when using automated control programs, provided the correct

address is known. See the MAUI Oscilloscopes Remote Control and

Automation Manual for more information about addressing.

The default host name is the product serial number, which is printed on

the rear of the unit and your registration card. This name is also available

from MAUI by going to Support > About. If the WaveRunner 8000-R is on

a network served by a DNS server, be sure it is known to the DNS server by

this name.

The WaveRunner 8000-R is preset to pull a dynamic IP address once it is

connected to a network served by a DHCP server, but this address will be

replaced whenever the oscilloscope is restarted after being powered down.

We recommend setting a static IP address for remote control, especially if

you will be using automated programs for control.

Remote Conguration

Connect an Ethernet cable from either port on the back panel to a network

access point. Be sure the WaveRunner 8000-R is on the same subnet as

the controller.

Using the monitor, go to Utilities > Utilities Setup and open Remote.

In the Control from eld, select either of two protocols for remote control

over LAN:

• TCPIP (VICP) supports MATLAB, VBA, VBS, C/C++ and JavaScript. To

use this method, also download and install the VICP Passport on the

controller.

• LXI (VXI11), the default, supports all of the the above, except MATLAB,

plus newer programming languages such as C# and Python. You do not

need the VICP Passport.

If desired, select Net Connections from the MAUI Remote dialog to access

the Windows networking dialogs and set a static IP address.

When nished, conrm that the correct IP address appears on the Remote

dialog and record it for use in VISA and ActiveDSO connect strings.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Teledyne Lecroy Messgerät Handbücher

Teledyne Lecroy

Teledyne Lecroy MDA810 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy M41h Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3000 Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PCI Express Gen 4x8 OCuLink Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline SD Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy BPA 600 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy SierraNet M328 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy PP009 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ZS Series Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy 980 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Everywhereyoulook DL02-HCM Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy frontline SODERA Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy DL03-ISO Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy ZD500 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP2060 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy 280 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVD3102 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy RP4030 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy LabMaster LM 10-25Zi-A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline Sodera LE Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Frontline Sodera LE Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy HVFO108 Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy MDA800A Bedienungsanleitung

Teledyne Lecroy

Teledyne Lecroy Quantumdata 780E Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung