Teledyne Lecroy Everywhereyoulook Frontline X500 Bedienungsanleitung

Introduction

Use this document for quick installation and setup.

The Frontline X500 is designed to capture Bluetooth, Wi-Fi, 802.15.4, logic signals, and various wired technologies such as

HCI-UART and USB. This quick start guide provides sufficient information to begin data capture. Detailed hardware and

software information is contained in the Wireless Protocol Suite Hardware and Software User Manual. The manual is also

available on FTE.com.

Frontline X500TM Protocol Analyzer

Components

Inspect the received shipping container for any damage. Unpack the container and account for each of the system

components listed on the accompanying packing list. Visually inspect each component for any damage. In the event of

damage, notify Teledyne LeCroy. Retain all shipping materials for shipper's inspection. The X500TM hardware does not

contain any user serviceable items. Any repairs and maintenance must be performed by a service technician that has been

trained and approved by Teledyne LeCroy.

The analyzer package includes the following components in addition to the X500:

Qty Description Qty Description

1 15V 8A Power Supply 2 RF 2.4 GHz Antenna (Bluetooth)

1 3' USB 3.0 Type C to C cable 4 RF 2.4/5/6 GHz Antenna (Wi-Fi)

1 6' Ethernet Cable (for future use) 2 Logic pods (Advanced and Elite

License)

Frontline X500TM

Protocol Analyzer 

Quick Start Guide

3Computer System Requirements

Supported Systems

• Operating System: Windows 10

• USB: USB 2.0 and later

Minimum Requirements

• Processor: Core i5 at 2.7 GHz

• RAM: 4 GB

• Free Hard Disk Space on C: drive: 20 GB

Install Software

From Download: Download the latest Wireless Protocol

Suite installer from FTE.com. http://fte.com/x500-soft.

Once downloaded, double-click the installer and follow

the directions. When the installation is complete pin the

Wireless Protocol Suite icon to your taskbar.

Set Up Hardware

1. Connect Cables

Power Connector: Connect the 15V Power adapter included with the product to the X500 hardware.

Connect to Host PC: Connect one end of the USB C-C 3.0 cable to the “Host” port on the X500 and connect another end

to the 3.0 port on the host computer. This will allow sending data from the hardware to the PC for the analysis.

Frontline X500 Rear Panel Controls

2. Attach Antennas

Remove the Frontline X500 hardware from the box and attach the six antennas to the SMA connectors on the front panel.

As their names indicate, BT Rx1 and BT Rx2 (disabled) are Bluetooth antenna connectors. Wi-Fi Rx1, 2, 3, and 4 are Wi-Fi

antenna to capture Wi-Fi 5 and Wi-Fi Rx 2 and 3 capture Wi-Fi 6/6E. The base of the antennas can be carefully rotated by

90 degrees so that the antenna points upward.

Frontline X500 Front Panel Controls and Indicators

3. Power-up Hardware

Power Button: The Power button illuminates when the unit is connected to a power source. Press and release the button

to power on or power off the system.

Status Indicators: Colored LEDs show the status of power, capture, and RF Status.

Table 1: X500 Front Panel Status Indicators

Indicator Color State Status Indicated

Power None Off Unit is powered off.

Green Constant Unit powered on with sufficient power source plugged in.

Blue Constant Unit powered on with sufficient power source plugged in.

Red Fast Flash Thermal warning threshold reached.

Solid System reaches thermal overload. Unit has started a

controlled/sequenced power down.

Status None Off No Status.

Green Constant Initialized and Ready. Not Capturing.

Blue Slow Flash Waiting for Capture Trigger (future).

Solid Actively capturing.

Yellow Slow Flash Initializing.

Fast Flash Shutting down.

Red Constant The unit failed to initialize or has a System Error.

Purple Constant Recovery Mode.

BT Rx1 None Off Antenna not in use