Tenmars TRIAXIAL ELF Bedienungsanleitung

TRIAXIAL ELF Magnetic

Field Meter

TM-192 / TM-192D

HB4TM1920002

Table of Contents

1. Introduction ............................................... 1

2. Application ................................................ 2

3. Features.................................................... 3

4. Identifying Parts ........................................ 4

5. Measurement Procedures......................... 5

6. Clock setup ............................................... 7

7. Auto power off setup ................................. 8

8. Continuity data logging setup.................... 9

9. Clear data logger memory ...................... 10

10. Clear all data logger memory ...................11

11. Single data memory ................................ 12

12. Viewing logged reading control key ........ 12

13. Specifications.......................................... 13

14. Battery replacement................................ 14

15. External DC Power ................................. 14

16. Safety Precaution.................................... 15

17. Software installation (192D) .................... 15

18. Note ........................................................ 17

TM-192/TM-192D

1. Introduction

Safety precautions should be taken against electric

appliances in places including medical institutions,

schools and residential districts, where people

usually stay for a long time, to prevent patients,

babies and senior citizens from exposure to high

electromagnetic waves.

An electromagnetic wave simply means the wave

motion of the electromagnetic field (EMF).

The change in electric fields produces magnetic

fields, and the change in magnetic fields can also

generate electric fields. The fluctuation of

correlation between each other is known as

“electromagnetic waves", which is a form of energy

similar to light and heat that can be transmitted

either by radiation in the air or by an electric

conductor.

It is suggested that rearrangements should be

made in homes and work locations where the

strongest electromagnetic fields are detected in

order to avoid prolonged exposure to excessive

electromagnetic fields.

TM-192/TM-192D

2. Application

zThis meter is applied to measuring magnetic

fields of extremely low frequency (ELF) of 30 to

2000Hz.

zIt is capable of measuring the magnetic field

radiation intensity that is produced from electric

transmission equipment, power lines, microwave

ovens, air conditioners, refrigerators, computer

monitors, video/audio devices and so forth.

zThe magnetic field unit is Tesla (T), Gauss (G),

milli-Gauss (mG) or micro-Tesla (μT).

1 T＝10,000 G 1 G＝1,000 mG

1μT＝10 mG

TM-192/TM-192D

3. Features

zUses three internal orthogonal sensors to test a

wide range of ELF magnetic fields, independent

of measurement angle.

zThe tester is designed to provide a quick, reliable

and easy way to measure magnetic field radiation

levels around power lines, home appliances and

industrial devices.

zThe tester is a cost-effective hand-held

instrument that was designed and calibrated to

measure magnetic field radiation at different

bandwidths from 30Hz to 2000Hz.

zDisplay microTesla(uT) or milliGauss(mG) units.

zData hold (HOLD), maximum Hold (MAX), and

minimum Hold(MIN) function.

zAuto range or manual range select mode.

zDatalogging capacity with Memory Size：500 data

sets (Model 192) or 9999 data sets(Model 192D).

zUSB PC interface (192D).

zTime and calendar function.

zLow battery indication “ ”.

zOver load display “OL”.

zAuto power OFF function .

TM-192/TM-192D

4. Identifying Parts

1. LCD display.

2. Power key.

3. maximum Hold and

minimum Hold key.

4. Data Hold key.

5. Record data and

Setup function left

key.

6. Range and Setup

function up key.

7. Reading and Setup

function right key.

8. Setup function key.

9. Units and Setup

function down key.

10.Enter key.

11.Calibration point for

12.Triple axis.

13.External power DC

9V.

14.USB interface

(TM-192D).

15.Tripod mounting

screw.

16.Battery cover.

TM-192/TM-192D

5. Measurement Procedures

zPress “ ” key turn on the meter, press “ ”

key again to turn OFF the meter.

zPress “ ” key to select milli-gauss (mG) or

micro-tesla (µT) unit.

zPosition the front of the meter to measure the

magnetic waves.

zRead the measured value. When manual range

mode is

selected, LCD will shown the mark, The

display of “OL” on the highest position indicates

there is an overload on the reading. Press “ ”

to select a higher range for measurement again.

zThe default value display is triaxial total magnetic

field reading. Press “ ” key to toggle between

independent three single-axis magnetic field

readings and triaxial total magnetic field reading.

zTo lock and keep the reading displayed on the

LCD, press “ ” or press “ ” again to

unlock.

TM-192/TM-192D

zTo retain the maximum and minimum value,

press “ ” key and the reading value displayed

on the LCD will keep

zupdating to the maximum value. Press again to

select minimum value, press and hold down

“” key 2 seconds to exit the maximum and

minimum mode.

zDue to the magnetic interference of the

environment field factors, this magnetic field

meter could display a reading value that is

greater than 0.5 mG prior to measuring. This is

not a malfunction of the tester.

zWith the tester in hand, move slowly towards to

the object under measurement until it is

physically touched.

zNotice how the field intensity increases as you

move closer to the object.

zIf the power of object was turned off during the

measurement, the reading of tester should return

to zero, unless an electromagnetic field from

other sources is detected.

TM-192/TM-192D

6. Clock setup

zThis meter clock uses 24 hour time.

zPress “ ” key to enter clock setting mode

(1.SET).

zPress “ ” or “ ” key to select option to

adjust.

zPress “ ” or “ ” key to change the digit.

zPress “ ” key to store the setup, exit the

mode.

TM-192/TM-192D

7. Auto power off setup

zPress “ ” key again to auto power off time

settingmode(2.SET).

zPress “ ” or “ ” key to change the auto

power off time.

zPress “ ” key to store the setup, exit the

mode.

zThe auto power off time default value is 5 minutes.

Range is 0 to 99 minutes. To cancel auto power

off, please set time to 0 minutes.

Andere Handbücher für TRIAXIAL ELF

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tenmars Messgerät Handbücher

Tenmars

Tenmars TM-91N Bedienungsanleitung

Tenmars

Tenmars TM-218 Bedienungsanleitung

Tenmars

Tenmars ST-130 Bedienungsanleitung

Tenmars

Tenmars TM-91 Bedienungsanleitung

Tenmars

Tenmars TM-740 Bedienungsanleitung

Tenmars

Tenmars TM-802 Bedienungsanleitung

Tenmars

Tenmars TM201 Bedienungsanleitung

Tenmars

Tenmars TM201 Bedienungsanleitung

Tenmars

Tenmars TM-206 Bedienungsanleitung

Tenmars

Tenmars TM-213 Bedienungsanleitung

Tenmars

Tenmars TM-203 Bedienungsanleitung

Tenmars

Tenmars TM-196 Bedienungsanleitung

Tenmars

Tenmars TM-185 Bedienungsanleitung

Tenmars

Tenmars TM-188 Bedienungsanleitung

Tenmars

Tenmars TM-101 Bedienungsanleitung

Tenmars

Tenmars TM- 4100D Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

Tenmars

Tenmars ST-140 Bedienungsanleitung

Tenmars

Tenmars TM-190 Bedienungsanleitung

Tenmars

Tenmars TM-206 Bedienungsanleitung

Tenmars

Tenmars HB2TM102001 Bedienungsanleitung

Tenmars

Tenmars TM-209 Bedienungsanleitung

Tenmars

Tenmars TM-741 Bedienungsanleitung

Tenmars

Tenmars TM-190 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung