Tennsco J1842A-N Bedienungsanleitung

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on products.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply

in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

PK-2310918

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Jumbo Counter-Height Storage Cabinet

Unassembled Models J1842A-N & J2442A-N

Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686

LOAD CAPACITIES PER SHELF LEVEL

48w x 18d

48w x 24d

400 lbs.

UNIT SIZE WEIGHT CAPACITY

EVENLY DISTRIBUTED

ASSEMBLY OF J1842A-N OR J2442A-N CABINET

Tools Needed: A free 11/32” nut driver is included with each Tennsco cabinet.

Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.

2. Place the back panels (Ref. No. 1) on a smooth surface,

making sure that the anges of both panels are facing up.

Overlap the right panel over the left anel. After aligning the

holes, bolt the two panels tightly together with four bolts

and nuts (Ref. Nos. 17 & 18).

1. The reference numbers used throughout this sheet refer to

the illustration on the back cover. This is to help you to

identify the various parts as they are mentioned.

3. Attach the left side (Ref. No. 2) to the back by placing ange

(A) around the back and bolting tightly together with four

bolts and nuts. Be sure that the lances on all the shelf

adjustment strips (B) point in the same direction.

5. Attach the right side (Ref. No. 3) to the back in the same

manner as you did in step 3, again making sure that

the ange is around the back and that the lances on

the shelf adjustment strips are pointed in the same

direction as those on the back and left side. Push the

side panel up so the studs in the top go through the holes

in the top ange of the side and fasten with three nuts.

6. Attach the sill (Ref. No. 4) to the sides. Place a nut

(Ref. No. 19) loosely on each of the studs and slide

the ends of the sill into the slots on both sides of the

unit. Then, securely tighten the nuts.

4. Attach the top (Ref. No. 8) to the unit by sliding the outer

ange over the back of the unit and the side ange to the

side panel on the unit. The threaded studs should go

through the holes in the top ange

of the side and fasten with

three nuts. Attach the

back to the top

using four

bolts and nuts.

All lances point UP on

the back and side.

Flange faces upward.

⁭

Flange goes

under back.

Slide ends into the slots on

the bottom of the sides.

7. Place the rear ange of the bottom shelf (Ref. No. 5)

into the bottom lances of the back. The ange with two

holes should face the front, hanging over the sill.

⁭

Nuts places loosely

on studs of the sill.

Insert the bottom into the bottom lances.

⁭

⁭⁭

⁭

1. Place the locking handle

(Ref. No. 10) on the right

hand door and fasten with

two #8-32 X 1/4 hex-head

bolts and lock washers,

provided with the handle.

2. Turn the handle to the

open position and

place the locking cam

(Ref. No. 11) over the

square shank of the

door handle. The latch

must be facing downward

as shown. Then place the

locking cotter pin (Ref. No.

13) through the hole of the

square shank.

3. With the handle still in the open position, hook the

locking bars (Ref. No. 9) to the locking cam (see

“A” at left). Once in position, slowly rotate the door

handle to the closed position so the lock bars

prot rude from the holes at the top and bottom

of the door (shown at right, below).

4. Slide the nylon lock bar

guide inserts (Ref. No.

12) over the lock bar

ends and through the

door slots (see “B” at

right). Push down rmly

until the guides snap

into place.

5. Attach the “dummy” handle

(Ref. No. 14) using two

#8-32 X 1/4 hex-head bolts

and lock washers.

Handle/Locking System Installation

8. Set the unit upright. Insert the second shelf at the desired

level. Be sure that the ange with the two holes should

face the front.

⁭

10. Cabinet must be level for doors to

open and close properly. Insert a

athead screwdriver into the two

leveling holes and turn the screws

until the cabinet is level. The cabinet

is now ready for use.

NOTE: In order to place the shelf, you must ﬁrst tilt

the shelf slightly to the left or right before inserting

into the unit.

9. Attach the left door (Ref. No. 6) to the unit by placing the

door on the hinges, aligning the hinge holes, placing the

hinge pins (Ref. No. 15) into the slots and tapping them in

until secure. Attach the right door (Ref. No. 7) to the unit

in the same manner as the left door.

⁭⁭

⁭

REPLACEMENT PARTS

⁭

Tennsco Nut Driver

(Ref No. 16)

Sill

(Ref No. 4)

Dummy Handle

(Ref No. 14)

Left Side

(Ref No. 2)

Top

(Ref No. 8)

Right Side

(Ref No. 3)

Cotter Pin

(Ref No. 13 )

Locking Bar Guide

Nylon Insert

(Ref No. 12)

Locking Bar Set

(Ref No. 9)

Locking Cam

(Ref No. 11)

Locking Handle

with Keys

(Ref No. 10)

Back Panels

(Ref No. 1)

REF. NO. DESCRIPTION

1 Back Panels 2 042BA 2 042BA

2 Left Side 1 042LSN 1 044LSN

3 Right Side 1 042RSN 1 044RSN

4 Sill 1 055SIN 1 055SIN

5 Shelf 2 306 2 307

6 Left Door 1 042LD 1 042LD

7 Right Door 1 042RD 1 042RD

8 Top 1 042TS 1 044TS

9 Locking Bar Set 1 978LB 1 978LB

10 Locking Handle w/keys & hardware 1 043LH 1 043LH

11 Locking Cam* 1 944LC 1 944LC

12 Locking Bar Guide Insert (Nylon)* 2 944GI 2 944GI

13 Cotter Pin* 1 CTRPN 1 CTRPN

14 Dummy Handle* 1 043DH 1 043DH

15 Hinge Pin* 4 944HP 4 944HP

16 Tennsco Nut Driver 1 TOOL-2 1 TOOL-2

17 #8-32 x 3/8” bolts (not shown above) 15 ** 15 **

18 #8-32 nuts (not shown above) 31 ** 31 **

19 Bolt w/lockwasher #8-32 x 3/8” bolts 4 ** 4 **

(not shown above)

*Included in Ref. No. 10, locking handle with keys and hardware (Part No. 043LH). **Available Locally

QTY. PART NO.

⁭

Left Door

(Ref No. 6)

NOTE: Additional hardware may be included for replacement purposes.

QTY. PART NO.

J1842A-N (18”d Cabinet) J2442A-N (24”d Cabinet)

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.

Shelf

(Ref No. 5)

⁭

Right Door

(Ref No. 7)

⁭

Hinge Pin

(Ref No. 7)

49B231

Dieses Handbuch passt für folgende Modelle

Andere Tennsco Inneneinrichtung Handbücher

Tennsco

Tennsco 1472 Bedienungsanleitung

Tennsco

Tennsco Capstone Shelving Units Bedienungsanleitung

Tennsco

Tennsco J2478C Bedienungsanleitung

Tennsco

Tennsco Imperial Shelving Bedienungsanleitung

Tennsco

Tennsco Jumbo Storage Cabinet J1878SU Bedienungsanleitung

Tennsco

Tennsco Q Series Bedienungsanleitung

Tennsco

Tennsco SRS-601878 Series Bedienungsanleitung

Tennsco

Tennsco 3070 Bedienungsanleitung

Tennsco

Tennsco WBHC-1516-MGY Bedienungsanleitung

Tennsco

Tennsco 7218 Bedienungsanleitung

Tennsco

Tennsco 1870RH Bedienungsanleitung

Tennsco

Tennsco B-3000 Bedienungsanleitung

Tennsco

Tennsco FB-12 Bedienungsanleitung

Tennsco

Tennsco 1472 Bedienungsanleitung

Tennsco

Tennsco Imperial Shelving 3630 Bedienungsanleitung

Tennsco

Tennsco BK6-121812-1 Bedienungsanleitung

Tennsco

Tennsco BCD18-72 Bedienungsanleitung

Tennsco

Tennsco STK-151872-1 Bedienungsanleitung

Tennsco

Tennsco Standard Combination Cabinet 7220 Bedienungsanleitung

Tennsco

Tennsco 1870 Bedienungsanleitung

Tennsco

Tennsco DWR-4218 Bedienungsanleitung

Tennsco

Tennsco 1470RH Bedienungsanleitung

Tennsco

Tennsco 1436 Bedienungsanleitung

Tennsco

Tennsco APT-3672S Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung