Tennsco J2478C Bedienungsanleitung

LOAD CAPACITIES PER SHELF LEVEL

48w x 18d

24w x 18d

400 lbs.

75 lbs.

UNIT SIZE WEIGHT CAPACITY

EVENLY DISTRIBUTED

PK-2840918

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Jumbo Combination Cabinet

Unassembled Model J2478C-N

Tennsco LLC.

, Dickson, TN 37056-1888 • (866) 446-8686

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on the units.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in

the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

ASSEMBLY OF J2478C-N CABINET

Tools Needed: A free 11/32” nut driver is included with each Tennsco cabinet.

Two people are recommended for assembly. Approximate assembly time: 30-40 minutes.

2. Place the 2-piece cabinet back (Ref.

No. 1) on a protected surface to

prevent scratching the paint.

The ange on the

bottom of the back

should be facing upward.

Bolt the back panels together with

seven bolts and nuts (Ref Nos. 19 & 20).

1. The reference numbers used throughout this sheet refer

to the illustration on the back cover. This is to help you

to identify the various parts as they are mentioned.

3. Attach the left side (Ref. No. 2) to the back by placing

ange (A) around the back and bolting together with

seven bolts and nuts. Be sure that the lances on all

shelf adjustment strips (B) point in the same direction.

5. Attach the right side (Ref. No. 3) to the back in the same manner

as you did in step 3, again, making sure that the ange is

around the back and that the lances on the shelf adjustment

strips are pointed in the same direction as those on the back and

left side. Push the side panel up so the studs in the top go

through the holes in the top

ange of the side and

fasten with three

nuts as in

step 4).

6. Attach the sill (Ref. No. 8) to the sides. Place nuts loosely on each

of the studs and slide the ends of the sill into the slots on both

sides of the unit. Then, securely tighten the nuts.

4. Attach the top (Ref. No. 5) to the unit by sliding the outer

ange over the back of the unit and the side ange on

the top over the side panel. The

threaded studs should go

through the holes in

the top ange

of the

side and

fasten with

three nuts.

Attach the

back to the

top using four

bolts and nuts.

7. Place the rear ange of one of the shelves (Ref. No. 4) into the

four bottom lances of the back. The front of the shelf will rest

on the sill.

⁭

All lances point UP on

both backs and side.

Flange goes

under back.

Flange faces upward.

Flanges

face upward

Threaded studs go

through the holes

in the ﬂange at the

top of the side.

Slide ends in to the slots

on the bottom of the sides.

Nuts placed loosely

on studs of the sill.

⁭

NOTE: When bolting the unit together, leave

the bolts slightly loose until Step 11, unless

otherwise speciﬁed.

Insert the bottom into

the bottom lances.

8. Insert the second shelf into the

second lance of the sides and

back of the top of the cabinet.

11.

Leveler

Access Holes

9. Insert the partition (Ref. No. 9) into the cabinet, aligning the

four holes in the partition with the holes in the cabinet

bottom and the cabinet shelf.

Attach with four bolts and nuts,

making sure that the bolts

are inserted from the top

downward to prevent stored

items from being snagged by

the ends. Insert the four partition

shelves (Ref. No. 12) at desired levels

using the method in step 8.

⁭

10. Using two people, set the unit upright.

Attach the left door (Ref. No. 6)

and right door (Ref. No. 7) to

the unit by placing the door

on the hinges, aligning the

hinges on the door to the

hinges on the sides, pushing

the hinge pins (Ref. No. 19)

through both hinges. Tap the

top of each hinge pin until

fully seated.

Attach the left coat rod bracket (Ref. No. 10) to the underside of

the shelf, inserting one bolt and nut through the hole provided

on the far right and far

left side. The open side of

the side brackets should

face into the unit. Place

the last bracket on the

coat rod (Ref. No. 11)

and insert the rod into

the other by exing the

second bracket. Secure

the bracket to the middle

of the shelf with one bolt

and nut through the hole

provided in the center

of the shelf. At this time,

tighten all of the nuts

and bolts around the

entire unit.

12. The cabinet must be level in order for the doors to close

properly. Levelers may be adjusted by placing the nut driver

through the hole in each end of the sill and adjusting the

leveling screw.

1. Place the locking handle

(Ref. No. 14) on the right

hand door and fasten with

two #8-32 X 1/4hex-head

bolts and lock washers,

provided with the handle.

2. Turn the handle to the

open position and

place the locking cam

(Ref. No. 15) over the

square shank of the

door handle. The latch

must be facing downward

as shown. Then place the

locking cotter pin (Ref. No.

17) through the hole of the

square shank.

3. With the handle still in the open position, hook the

locking bars (Ref. No. 13) to the locking cam (see

“A” at left). Once in position, slowly rotate the door

handle to the closed position so the lock bars

prot rude from the holes at the top and bottom

of the door (shown at right, below).

4. Slide the nylon lock bar

guide inserts (Ref. No.

16) over the lock bar

ends and through the

door slots (see “B” at

right). Push down rmly

until the guides snap

into place.

5. Attach the “dummy” handle

(Ref. No. 18) using two

#8-32 X 1/4hex-head bolts

and lock washers.

Handle/Locking System Installation

⁭

REPLACEMENT PARTS

⁭

Tennsco Nut Driver

(Ref No. 18)

Hinge Pin

(Ref No. 19)

Coat Rod

(Ref No. 11)

Sill

(Ref No. 8)

Coat Rod

Bracket

(Ref No. 10)

Dummy Handle

(Ref No. 18)

Left Side

(Ref No. 2)

Top

(Ref No. 5)

Shelf

(Ref No. 4)

Right Side

(Ref No. 3)

Cotter Pin

(Ref No. 17)

Locking Bar Guide

Nylon Insert

(Ref No. 16)

Locking Bar Set

(Ref No. 13)

Locking Cam

(Ref No. 15)

Locking Handle

with Keys

(Ref No. 14)

Back Panel

(Ref No. 1)

REF. NO. DESCRIPTION

1 Back Panels 2 055BA

2 Left Side 1 056LS

3 Right Side 1 056RS

4 Shelf 2 307

5 Top 1 055T24

6 Left Door 1 056LD

7 Right Door 1 056RD

8 Sill 1 055SI

9 Partition 1 046PA

10 Coat Rod Bracket 3 045RB

11 Coat Rod 1 055CR

12 Partition Shelf 4 JPS24

13 Locking Bar Set 1 043LB

14 Locking Handle w/keys & hardware 1 043LH

15 Locking Cam* 1 944LC

16 Locking Bar Guide Insert (Nylon)* 2 944GI

17 Cotter Pin* 1 CTRPN

18 Dummy Handle* 1 043DH

19 Hinge Pins* 8 944HP

20 Tennsco Nut Driver 1 TOOL-2

21 #8-32 x 3/8” bolts (not shown above) 25 **

22 #8-32 nuts (not shown above) 35 **

*Included in Ref. No. 14, locking handle with keys and hardware (Part No. 043LH). **Available Locally

QTY. PART NO.

⁭

Left Door

(Ref No. 6)

Right Door

(Ref No. 7)

⁭

Partition

(Ref No. 9)

⁭

Partition Shelf

(Ref No. 12)

NOTE: Additional hardware may be included for replacement purposes.

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.

49B284

Dieses Handbuch passt für folgende Modelle

Andere Tennsco Inneneinrichtung Handbücher

Tennsco

Tennsco 1472 Bedienungsanleitung

Tennsco

Tennsco EB-12 Bedienungsanleitung

Tennsco

Tennsco 7224 Bedienungsanleitung

Tennsco

Tennsco 1842 Bedienungsanleitung

Tennsco

Tennsco J1878A-N Bedienungsanleitung

Tennsco

Tennsco FB-12 Bedienungsanleitung

Tennsco

Tennsco 3070 Bedienungsanleitung

Tennsco

Tennsco J2478A-N-W Bedienungsanleitung

Tennsco

Tennsco FS350 Bedienungsanleitung

Tennsco

Tennsco 1870 Bedienungsanleitung

Tennsco

Tennsco B-8400 Bedienungsanleitung

Tennsco

Tennsco Enclosed Foreman’s Desk Bedienungsanleitung

Tennsco

Tennsco LSS-361872 Bedienungsanleitung

Tennsco

Tennsco 1436 Bedienungsanleitung

Tennsco

Tennsco 1472 Bedienungsanleitung

Tennsco

Tennsco zt7 Series Bedienungsanleitung

Tennsco

Tennsco 1470RH Bedienungsanleitung

Tennsco

Tennsco ZL7 Series Bedienungsanleitung

Tennsco

Tennsco WELDED 3-PERSON LOCKER Bedienungsanleitung

Tennsco

Tennsco CINCO NIVELES Bedienungsanleitung

Tennsco

Tennsco B-8400 Bedienungsanleitung

Tennsco

Tennsco BK6-121812-1 Bedienungsanleitung

Tennsco

Tennsco Capstone Shelving Units Bedienungsanleitung

Tennsco

Tennsco 1870 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung