Tennsco Q Series Bedienungsanleitung

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCERETAIN INSTRUCTIONS FOR FUTURE REFERENCE

PK-2060919PK-2060919

Q-Line Open Style

Industrial Shelving

Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686

LIMITED WARRANTYLIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in

the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on units.

QO6-3612S and QO6-3612AB

Starter unit and Adder unit

QO5-3612S

Starter unit

ASSEMBLY OF OPEN Q-LINE INDUSTRIAL SHELVING

The reference numbers used throughout this sheet refer to the illustration on the back cover.

This is to help you to identify the various parts as they are mentioned.

Q-Line uprights come in three different styles, as shown

below.

2. Create the right side of the shelving units by laying two

uprights side by side on a at surface. Be sure that the

short side of the OAP upright(s) (Ref. No. 1a) is facing up,

as shown below.

3. Attach the two side sway braces (Ref. Nos. 2a or 2b),

beginning in the 20th hole from the top of each upright

(approximately 20” from the top), using two 1/4”-20

5/8” bolts and nuts (Ref. No. 6). The side sway braces

attach to the longer side of the uprights (the side with

two sets of holes). Bolt the braces into the small holes

near the edge of the uprights as shown in circles below.

Note the hole pattern of two round holes and then one

square hole, repeating every 3”, which should help

facilitate proper placement of the bolts. Finger tighten only

at this point.

Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.

Tools required: 7/16” or nut driver or socket and a athead screwdriver.

Standard

Beaded Post

(BTP)

⁭⁭

Offset

Angle Post

(OAP)

Heavy

Beaded Post

(HBP)

These three upright styles may be used in several different

combinations. In order to better understand these

instructions, please examine the following congurations

to determine which type of installation you will be assembling:

Single unit with four

Offset Angle Posts

Two or more units with four offset

angle posts per section

Single unit with two offset

angle posts in rear and two

standard or heavy beaded

posts in front.

Two or more units using standard or heavy beaded

posts in front and offset angle posts in rear

NOTE: One side of the upright is longer than the

other, and contains two sets of holes. When laying

the uprights side by side, this long side should be

on the ﬂoor, and the short side should be pointing

into the air.

If your unit will use BTP or HBP uprights in the front (Ref.

Nos. 1b or 1c), be sure to select the proper upright and

that the open edge is facing the OAP upright, as shown

below in the below gure.

⁭⁭

4. Attach the other end of both sway braces. The information

below will help will help you to know how many holes

should be between the top and bottom of the sway

braces. Count the holes carefully, as an incorrect count

will cause the upright to be the wrong depth to hold the

shelves.

⁭⁭

EXAMPLE:

12” deep unit has 34

holes between bolts.

12”

15”

18”

24”

30”

36”

7/8”

5/8”

36 holes (35”)

35 holes (34”)

34 holes (33”)

30 holes (29”)

34 holes (33”)

28 holes (27”)

Unit Depth Brace Length Distance Between Bolts

5. Place one 1/4”-20 x 5/8” bolt and nut in the hole where

the two sway braces cross. Insert the bolt from the outside

of the uprights, so that the nut will be inside the unit.

Again, nger tighten only for the time being.

⁭⁭

6. Repeat steps 2 through 5 for the left uprights. Again, be

sure to note the types of uprights you should

be using (according to the illustrations in step 2) for your

type of installation. If you have purchased an adder unit

such as the last illustration in step 1, please note that only

one BTP or HBP is used in between the units.

You should now have complete left and right sides of your

shelving unit, with sway brace bolts and nuts

still nger-tightening only.

7. Have an associate hold one upright while you place four

shelf clips (Ref. No. 3) in the top and bottom holes of each

post, as shown below.

⁭⁭

⁭⁭⁭⁭

8. Place a shelf (Ref. No. 4a or 4b) onto the bottom two clips.

9. Tie in the two sets of uprights with the bottom shelf.

10. Place the top shelf over the four clips at the top of the

upright.

11. Bolt the rear sway braces (Ref. No. 5) on the back of the

unit, using ve 1/4”-20 x 5/8” bolts and nuts, as shown.

Again, the top of the sway braces should be in the 20th

hole from the top of each upright (approximately

20” from the top). The chart below will help you determine

the proper number of holes between the top and bottom

of the sway braces. Note that the hole count includes

the holes which will contain the bolts.

36”

42”

48”

11/32”

44 holes (43”)

38 holes (37”)

30 holes (29”)

Unit Depth Brace Length Distance Between Bolts

⁭⁭

12. Position the remaining shelf clips according to your desired

shelf heights, and place the shelves over the clips. Keep

in mind while placing the clips, that the hole pattern of

two round holes and then one square hole repeated every

3”, can greatly help in aligning the clips evenly.

NOTE: Some shelves, depending upon placement,

could possibly require temporary removal of one

end of a sway brace in order to insert the shelf.

13. Tighten up all the bolts and nuts on the rear and side sway

braces. There are fteen bolts and nuts to tighten, ve for

each pair of sway braces.

14. If you purchased the optional label holder (Ref. No. 8),

place it on the front edge of the shelf and secure with

three provided P-38F plastic tabs.

15. If you purchased the optional front base strip (Ref. No.

7), bolt it to the outside of the bottom shelf with the three

self-tapping screws provided. Make sure that the ends of

the front base strip are behind the front anges of the

uprights.

⁭⁭

16. For even better reinforcement, place two 1/4”-20 x 5/8” bolts and nuts

through each corner of each shelf, and into the small holes of the upright.

17. If more than one unit is to be used in a row, bolt a pair of upright posts to the rst unit with 1/4”-20 x 1”

bolts and nuts. Note that where BTP or HBP posts are used, two units will share one post. The pair of side

braces on the rst unit becomes a common pair of the two units.

Two new

upright posts

Side sway

braces are

shared by

both units.

⁭⁭⁭⁭

⁭⁭

18. If two units are to be used back-to-back, the back braces on the rst unit become a common pair for the two units.

⁭⁭

Two new

upright

posts

Back sway

braces are

shared by

both units

REPLACEMENT PARTSREPLACEMENT PARTS

NOTE: Additional hardware may be included for replacement purposes.NOTE: Additional hardware may be included for replacement purposes.

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.However, should your unit contain missing or damaged parts, please contact your purchase location.

**Available Locally

49B20649B206

DESCRIPTIONDESCRIPTION

BASIC UNITBASIC UNIT

PART NUMBERSPART NUMBERS

Offset Angle Post

Beaded T-Post

Heavy Duty Beaded Post

End Sway Braces (Pair) 12” to 24”

End Sway Braces (Pair) 30” to 36”

Shelf Clip

22 Gauge Steel Shelf

20 Gauge Steel Shelf

Rear Sway Braces (Pair) 48”

1/4”-20 x 5/8” Bolts and Nuts**

OAP-hh

BTP-hh

HBP-hh

ESB-1224

ESB-3036

T- 1

Q2-wwdd

Q-wwdd

RSB-48

FBS-ww2

LH-ww

HD-3687

BD-ddhh

BF-wwhh

EP-ddhh

BP-wwhh

FP-1

SD-ddhh

BX-wwdd

REF.REF.

NO.NO.

Heavy DutyHeavy Duty

Beaded PostBeaded Post

(Ref No. 1c)(Ref No. 1c)

⁭⁭

Shelf ClipShelf Clip

(Ref No. 3)(Ref No. 3)

⁭⁭

1/4”-20 Nut

(Ref No. 6)(Ref No. 6)

1/4”-20 x 5/8”Bolt

(Ref No. 6)(Ref No. 6)

⁭⁭

Front Base StripFront Base Strip

(Ref No. 7)(Ref No. 7)

⁭⁭

Optional Front Base Strip

Optional Label Holder

Optional Hinged Door & Frame*

Optional Bin Dividers*

Optional Bin Front*

Optional End Panel*

Optional Back Panel*

Optional Foot Plate*

Optional Sliding Divider*

Optional Shelf Box*

DESCRIPTIONDESCRIPTION

OPTIONALOPTIONAL

PART NUMBERSPART NUMBERS

REF.REF.

NO.NO.

*Not Shown

Beaded T-PostBeaded T-Post

(Ref No. 1b)(Ref No. 1b)

Shelf Label HolderShelf Label Holder

(Ref No. 8)(Ref No. 8)

Steel ShelfSteel Shelf

(Ref Nos. 4a & 4b)(Ref Nos. 4a & 4b)

⁭⁭

Rear Sway BracesRear Sway Braces

(Ref No. 5)(Ref No. 5)

⁭⁭

End Sway BracesEnd Sway Braces

(Ref Nos. 2a & 2b)(Ref Nos. 2a & 2b)

⁭⁭

O󰀨set Angle Post O󰀨set Angle Post

(Ref No. 1a)(Ref No. 1a)

⁭⁭

Part No. is composed of prex shown plus a combination of the opening of the unit. ww = Width, dd = Depth & hh = Height.

If the shelf has a diamond shaped hole on the end ange on one side, it is a 20 gauge shelf; if not, it is a 22 gauge shelf.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tennsco Inneneinrichtung Handbücher

Tennsco

Tennsco Z-Line Bedienungsanleitung

Tennsco

Tennsco FB-12 Bedienungsanleitung

Tennsco

Tennsco 3070 Bedienungsanleitung

Tennsco

Tennsco RGL-1236S Bedienungsanleitung

Tennsco

Tennsco 1480 Bedienungsanleitung

Tennsco

Tennsco 1470RH Bedienungsanleitung

Tennsco

Tennsco RGL-1236S Bedienungsanleitung

Tennsco

Tennsco Z-Line Steel Shelf Unit Bedienungsanleitung

Tennsco

Tennsco MB-1-2542-MGY Bedienungsanleitung

Tennsco

Tennsco 1442 Bedienungsanleitung

Tennsco

Tennsco J1878A-N Bedienungsanleitung

Tennsco

Tennsco FB-12 Bedienungsanleitung

Tennsco

Tennsco Jumbo Storage Cabinet J2478SU Bedienungsanleitung

Tennsco

Tennsco 1870RH Bedienungsanleitung

Tennsco

Tennsco B-3000 Bedienungsanleitung

Tennsco

Tennsco 1871 Bedienungsanleitung

Tennsco

Tennsco 7224 Bedienungsanleitung

Tennsco

Tennsco BK6-121812-1 Bedienungsanleitung

Tennsco

Tennsco 7218 Bedienungsanleitung

Tennsco

Tennsco B-6000 Bedienungsanleitung

Tennsco

Tennsco JUMBO Gebrauchsanweisung

Tennsco

Tennsco Standard Combination Cabinet CVD7214 Bedienungsanleitung

Tennsco

Tennsco APT-3672S Bedienungsanleitung

Tennsco

Tennsco 4218 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung