Timeguard MLSA360N Handbuch

Installation & Operating Instructions

360° Night Eye PIR

Light Controller

Model: MLSA360N

1. General Information

These instructions should be read carefully and retained for further

reference and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the

PIR sensor is switched off and the circuit supply fuses are removed

or the circuit breaker turned off.

• It is recommended that a qualified electrician is consulted or used for

the installation of this PIR sensor and install in accordance with the

current IEE wiring and Building Regulations.

• Check that the total load on the circuit including when this PIR sensor

is fitted does not exceed the rating of the circuit cable, fuse or

circuit breaker.

3. Technical Specifications

• 230V AC 50 Hz

• This PIR is of Class ll Construction and must not be earthed

• Motion Detection Range: Up to 12 metres

•Detection Angle: 360°

• Maximum Switching Load: 3000W Halogen Lighting

500W Fluorescent Lighting

140W LED Lighting

150W Discharge Lighting (SON, HQI)

• Time ON adjustment: 5 seconds to 12 minutes

•Dusk Level Adjustment: Day and Night or Night time only operation

• IP45 Rated for restricted external applications

• CE Compliant

• EC Directives: Conforms to latest directives

• Manual Override

4. Selecting a Location

• The motion detector has number of detection zones, at various vertical

and horizontal angles as shown (See diagram “A”)

• The optimum mounting height is 2.5m (the minimum is 1.7m)

• Careful positioning of the sensor will be required to ensure optimum

performance (See diagram “A” & “B” detailing detection range

and direction.)

• The sensor is more sensitive to movement ACROSS its field of vision than

to movement directly TOWARDS (See diagram “B”). Therefore position

the unit so that the sensor looks ACROSS the likely approach path.

• Avoid positioning the sensor where there are any sources of heat in

the detection area (extractor fans, tumble dryer exhausts etc.) including

opposite any other light sources such as other security lights

(See diagram “C”).

• Reflective surfaces (i.e. pools of water or white painted walls)

may cause false activation under extreme conditions.

Diagram A

5. Installation

• Ensure the mains supply is switched off and the circuit supply fuses

are removed or the circuit breaker turned off.

• An isolating switch should be installed to enable the power to be

switched ON & OFF for maintenance purposes and to activate the

manual/auto override function.

Diagram B

Diagram C

• Remove the mounting plate from the PIR by releasing one of the lugs

(left or right side) firmly grip with your hand, and slide in a downward

direction to release.

• Mark the position of the fitting holes using the mounting plate as a

template (See section 6. Mounting Installation Steps, for the different

ways of mounting the PIR). Drill out the mounting holes taking care to

avoid any joists, electrical cables or water/gas pipes that may be hidden

beneath the surface. Insert the rawl plugs into the holes.

• Pass the 230V 50Hz mains supply and load cables through the cable

entry points on the backing pate, ensuring the grommet(s) is used

to maintain the IP rating of the PIR sensor.

• Fix the mounting plate to the wall using the correct screws for the

rawl plugs installed.

• Terminate the cables into the terminal block ensuring correct polarity

is observed and that all bare conductors are sleeved (see section 7.

Connection Diagram).

• Ensure all connections are secure.

• Slide the main body back onto the mounting plate then pull in a

downwards direction so that it is fully engaged with the mounting plate.

• Secure the unit by replacing the screw on the underside.

6. Mounting Installation Steps

Wall Mounting

• Please use the following steps for wall/surface mounting.

Ceiling/Eave Mounting

• Please use the following steps for ceiling/eave mounting.

External Corner Mounting

• Please use the following steps for external corner mounting.

• Please use the following steps to remove the PIR from the corner

mounted bracket.

7. Connection Diagram

• Connect the cables to the terminal block as follows;

Mains Supply

Live (Brown or Red) to L

Neutral (Blue or Black) to N

A ‘Loop Terminal’ is provided

should a 3 core cable be used,

which is marked .

Load

Switch Live (Brown or Red) to L1

Neutral (Blue or Black) to N

A ‘Loop Terminal’ is provided

should a 3 core cable be used,

which is marked .

LLN

MAINS

SUPPLY LOAD

ISOLATION SWITCH

LOOP

TERMINAL

8. Operation and Testing

Adjustment

• The PIR can be adjusted using a flathead screwdriver;

Walk Test Procedure

• The sensor will rotate from left to right, and tilt forward or backward.

• The small arrow on the underside of the sensor indicates the direction

of the main detection area.

• The adjustment knobs located on the sides of the sensor head factory

set to “Walk Test Mode” i.e. LUX set to the ‘Sun’ symbol and the

Time set to the minimum.

• Turn the power to the unit ON. The lamp will immediately illuminate

as the unit goes through its “warm-up” period. After approximately

1 – 2 minutes the lamp will extinguish. Try to remain outside the

detection area during the warm-up period.

• Adjust the sensor to point in the desired direction for best coverage.

• The unit will now operate during daytime as well as at night,

illuminating the lamp for approx. 5 seconds each time.

• Walk across the detection area approx. 2.5 metres from the unit. As you

cross a detection "zone" the lamp will illuminate. Now stand still until

the lamp extinguishes (this should take approx. 5 seconds).

• Start moving again. As you cross each "zone" the lamp will illuminate.

• Repeat the above, walking at various distances and angles to the unit.

This will help you to establish the detection pattern.

• If the detection area is too small for your requirements, try angling the

sensor head up. This will increase the coverage distance. Angling the

head downwards will reduce the range should a smaller coverage area

be required.

Inhaltsverzeichnis

Andere Timeguard Controller Handbücher

Timeguard

Timeguard PDRS1500N Montageanleitung

Timeguard

Timeguard PDWM1500 Handbuch

Timeguard

Timeguard PDFMMINIL Handbuch

Timeguard

Timeguard SLDD1000 Handbuch

Timeguard

Timeguard SLFM360N Handbuch

Timeguard

Timeguard SLFM360L Handbuch

Timeguard

Timeguard TRTD7N Handbuch

Timeguard

Timeguard MLB3000 Handbuch

Timeguard

Timeguard RTS113Q Programmierhandbuch

Timeguard

Timeguard SLW360L Handbuch

Timeguard

Timeguard TLRX05 Handbuch

Timeguard

Timeguard PDSM1500 Handbuch

Timeguard

Timeguard ProgramaSTAT UFPT24 Bedienungsanleitung

Timeguard

Timeguard PDFM1500N Handbuch

Timeguard

Timeguard SLB2300RF Handbuch

Timeguard

Timeguard E269H-Synchronous Handbuch

Timeguard

Timeguard SLB2300 Handbuch

Timeguard

Timeguard TS900B Bedienungsanleitung

Timeguard

Timeguard SLW360N Handbuch

Timeguard

Timeguard TS900N Montageanleitung

Timeguard

Timeguard PDFM1500 Handbuch

Timeguard

Timeguard NSLDD1000 Handbuch

Timeguard

Timeguard TRT039N Handbuch

Timeguard

Timeguard MTLW3000 Handbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung