Timeguard NSLDD1000 Handbuch
Installation & Operating Instructions
3000W Dusk to Dawn
Light Controller
Model: NSLDD1000 – White
1
1. General Information
These instructions should be read carefully and retained for further
reference and maintenance.
2. Safety
• Before installation or maintenance, ensure the mains supply to the
sensor is switched off and the circuit supply fuses are removed or
the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for
the installation of this sensor and install in accordance with the
current IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this sensor
is fitted does not exceed the rating of the circuit cable, fuse or
circuit breaker.
3. Technical Specifications
• 230V AC 50 Hz
• This PIR is of Class ll Construction and must not be earthed
• Maximum Switching Load: 3000W Halogen Lighting
500W Fluorescent Lighting
140W LED Lighting
150W Discharge Lighting (SON, HQI)
• Operation: Dusk – Dawn,
Dusk to 2/4/8 hours OFF,
(adjustable Dusk sensing)
• IP44 Rated suitable for restricted external applications
• CE Compliant
• EC Directives: Conforms to latest directives
2
4. Installation
• Ensure the mains supply is switched off and the circuit supply
fuses are removed or the circuit breaker turned off.
• An isolating switch should be installed to enable the power to be
switched ON & OFF for maintenance purposes.
• Open the unit by gently prying the “ears” on each side of the unit
(See diagram “A”). This can be done without a tool, but if you prefer use
a flat blade screwdriver, but be careful not to damage the clips. The front
cover is hinged at the top and the front cover will swing open upwards.
• Mark the position of the fitting holes using the unit as a template.
Drill out the mounting holes taking care to avoid any joists, electrical
cables or water/gas pipes that may be hidden beneath the surface.
Insert the rawl plugs into the holes.
• Pass the 230V 50Hz mains supply and load cables through the cable
entry points on the unit, ensuring the grommet(s) is used to maintain
the IP rating of the sensor.
• Fix the unit to the wall using the correct screws for the
rawl plugs installed.
• Terminate the cables into the terminal block ensuring correct polarity
is observed and that all bare conductors are sleeved (See section 5.
Connection Diagram).
• Attach the supplied cable clamp ensuring not to overtighten.
• Close the front cover.
3
5. Connection Diagram
• Connect the cables to the terminal block as follows;
9+]
0DLQV6XSSO\,1
230V 50Hz Mains Supply IN
Live (Brown or Red) to L
Neutral (Blue or Black) to N
A ‘Loop Terminal’ is provided
should a 3 core cable be used,
which is marked .
Load
Switch Live (Brown or Red) to L1
Neutral (Blue or Black) to N
A ‘Loop Terminal’ is provided
should a 3 core cable be used,
which is marked .
Note: The N terminals are common.
4
Diagram A
Diagram B
Front
cover
hinges
upwards
5
6. Testing
• The adjustment knobs located on the side of the sensor head
(see diagram “D”) are factory set to “Daylight Mode” i.e. LUX set
to the ‘Sun’ symbol.
Diagram C
Diagram D
View on underside of unit shows adjustments
Lux Time on
6
• The Dusk setting determines at which light level the NSLD1000 will turn
its connected load “ON”. Turning this setting fully clockwise allows you
to test the circuit during daylight.
• Connect the unit to the mains and switch power ON.
• After a short delay, the unit will switch ON. This is indicated by the
red LED (See diagram “C”). Any attached lights will also illuminate.
7. Setting up for Automatic Operation
• The TIME control determines how long the lamp remains illuminated
after activation. There are 4 designated “time on” settings 2, 4, 8 hours
and dusk until dawn.
• The DUSK (LUX) control determines the level of darkness required
for the unit to start operating. The setting is best achieved by the
procedure below;
1. Set the Dusk control knob fully clockwise and the Time control to the
required number of hours or dusk/dawn.
2. When the ambient light level reaches the level of darkness at which
you wish the lamp to become operative (i.e. at dusk) SLOWLY rotate
the control in an anti-clockwise direction until a point is reached
where the lamp illuminates.
3. Leave the control set at this point.
• At this position the unit should become operative at approximately
the same level of darkness each evening.
• Observe the operation of the unit. If the unit is starting to operate too
early (i.e. when it is quite light) adjust the control slightly anti-clockwise.
If the unit starts to operate too late (i.e. when it is very dark). Adjust the
control slightly clockwise.
• Continue to adjust until the unit operates as desired.
7
8. Troubleshooting
Problem
• PIR sensor will not
operate at night.
Solution
The level of ambient light in the area may too
bright to allow operation at the current DUSK
setting. During the hours of darkness first turn
the Time Delay knob to minimum then adjust
the DUSK control slowly anti-clockwise until the
lamp illuminates. Refer to previous section for
more details.
Adjust the setting anti-clockwise to lower the
level of ambient light required for activation.
• PIR activates during
the daytime.
8
3 Year Guarantee
In the unlikely event of this product becoming faulty due to defective material
or manufacture within 3 years of the date of purchase, please return it to
your supplier in the first year with proof of purchase and it will be replaced
free of charge. For years 2 and 3 or any difficulty in the first year,
telephone the helpline on 020 8450 0515.
Note: A proof of purchase is required in all cases. For all eligible replacements
(where agreed by Timeguard) the customer is responsible for all shipping/
postage charges outside of the UK. All shipping costs are to be paid in
advance before a replacement is sent.
9
Inhaltsverzeichnis
Andere Timeguard Controller Handbücher
Timeguard
Timeguard SLFM360N Handbuch
Timeguard
Timeguard SLW360N Handbuch
Timeguard
Timeguard SureTime STLW1000 Handbuch
Timeguard
Timeguard RTS113Q Programmierhandbuch
Timeguard
Timeguard SLB2300RF Handbuch
Timeguard
Timeguard MTLW3000 Handbuch
Timeguard
Timeguard TS900N Montageanleitung
Timeguard
Timeguard ProgramaSTAT UFPT24 Bedienungsanleitung
Timeguard
Timeguard ELU56 Handbuch
Timeguard
Timeguard TRTD7N Handbuch
Timeguard
Timeguard PDWM1500 Handbuch
Timeguard
Timeguard TRT039N Handbuch
Timeguard
Timeguard PDSM1500 Handbuch
Timeguard
Timeguard PDFM1500 Handbuch
Timeguard
Timeguard RTS113 Programmierhandbuch
Timeguard
Timeguard E269H-Synchronous Handbuch
Timeguard
Timeguard PDFMMINIL Handbuch
Timeguard
Timeguard SLDD1000 Handbuch
Timeguard
Timeguard PDRS1500N Montageanleitung
Timeguard
Timeguard SLB2300RF Handbuch
