Toro WHEEL HORSE 71216 Handbuch

The TORO Company – 1995

FORM NO. 3317–303 Rev. A

SET-UP

INSTRUCTIONS

MODEL NO. 71216 – 5900001 & UP

WHEEL HORSELAWN TRACTOR

Loose Parts

Note: Use the chart below to verify all parts have been shipped.

DESCRIPTION QTY. USE

Front Wheel

Flat Washer

Cotter Pin

Hub Cap

Install front wheels.

Spacer (on axle)

Rear Wheel

Square Key

Flat Washer

E-ring

Hub Cap

Install rear wheels.

Steering Wheel

Roll Pin

1Install steering wheel.

Seat

Knob

Flat Washer

Wire Clip (on seat pan)

Instal the seat.

Bolt 1/4–20 x 3/4”

Wing nut

2Install battery cables.

Spring Hook 1Used to install lift assist spring.

Key 1Use in ignition switch.

Operator’s Manual

Safety Booklet

Certificate of Conformance

Noise Certifecate

Read and watch before operating tractor.

Registration Card 1Fill out and mail the card.

Set-Up Instructions

Install Front Wheels

Note: If wheels are already installed, refer to

Check Tire Pressure (below).

1. Install wheel onto axle with valve stem out.

2. Slide the flat washer onto the axle. Insert cotter

pin through the axle and bend the ends of the pin

apart (Fig. 1).

3. Push the hub cap (Fig. 1) onto the end of the

axle.

Figure 1

1. Flat washer

2. Cotter pin 3. Hub cap

4. Repeat steps 1–3 on opposite side.

5. Grease the wheel bearings.

Install Rear Wheels

1. Grease the axle to prevent corrosion. Slide

spacer then wheel, with valve stem to the

outside, onto axle (Fig. 2).

2. Slide key into keyway of axle and wheel hub

(Fig. 2).

3. Slide washer onto axle and secure with E-ring

(Fig. 2).

4. Press hub cap over washer (Fig. 2).

1779

Figure 2

1. Axle

2. Spacer

3. Wheel

4. Key

5. Washer

6. E-rung

7. Cap

Check Tire Pressure

Check front and rear tire pressure. See Operator’s

Manual for specification.

Set-Up Instructions

Install Steering Wheel

1. Move front wheels straight ahead.

2. Slide the steering wheel over shaft. Line up the

hole in the steering wheel with the hole in the

shaft (Fig. 3). From the seat you should be able

to read the brand logo on the steering wheel.

3. To align the holes, insert a punch or long nail

partially through the holes in the steering wheel

and shaft. Then insert the roll pin into the hole

on the opposite side.

4. Using a hammer, drive the roll pin in until it is

flush with the outside of the steering wheel

(Fig. 3).

Figure 3

1. Steeringwheel 2. Roll pin

Install Seat

Note: If the seat is already installed, proceed

to Activate The Battery, page 4.

1. Insert seat switch wire cable through the hole in

the seat base (Fig. 4).

2. Position the seat onto the seat base by inserting

the two shoulder bolts through key hole

openings at the end of both slots (Fig. 4).

3. Thread the knob and flat washer through slot

into the rear center hole in the seat (Fig. 4).

Adjust the seat and tighten the knob.

4. Push the seat switch connector fully into the

wire harness connector (Fig. 4).

5. Secure the seat switch wire cable to seat base

with wire clip (Fig. 4).

Note: Check seat switch wire routing, it must

not be pinched in seat brackets.

Figure 4

1. Seat

2. Wire and connector

3. Shoulder bolts

4. Knob and flat washer

5. Wire clip

6. Connectors

Set-Up Instructions

Activate the Battery

Bulk electrolyte with 1.260 specific gravity must be

purchased from a local battery supply outlet.

1. Remove the battery and battery box from the

tractor: refer to Operator’s Manual, Removing

the Battery.

IMPORTANT: Be careful not to damage the

long vent tube when removing the battery

box.

POTENTIAL HAZARD

•Battery electrolyte contains sulfuric acid

which is a deadly poison and it causes

severe burns.

WHAT CAN HAPPEN

•If you carelessly drink electrolyte you could

die or if it gets onto your skin you will be

burned.

HOW TO AVOID THE HAZARD

•Do not drink electrolyte and avoid contact

with skin, eyes or clothing. Wear safety

glasses to shield your eyes and rubber

gloves to protect your hands.

•Fill the battery where clean water is always

available for flushing the skin.

•Follow all instructions and comply with all

safety messages on the electrolyte container.

2. Unscrew six filler caps from the battery. Slowly

pour electrolyte into each cell until the level is

up to the “UPPER” line on the battery case

(Fig. 5).

Figure 5

1. Fillercaps

2. Electrolyte 3. Upper line

3. Leave the filler caps off and connect a 3 to 4

amp battery charger to the battery posts (Fig. 6).

Charge the battery at a rate of 4 amperes or less

for 4 hours (12 volts).

Figure 6

1. Positive post

2. Negative post 3. Charger red (+) wire

4. Charger black (–) wire

Set-Up Instructions

POTENTIAL HAZARD

•Charging battery produces gasses.

WHAT CAN HAPPEN

•Battery gasses can explode.

HOW TO AVOID THE HAZARD

•Keep cigarettes, sparks and flames away

from battery.

4. When the battery is fully charged, disconnect the

charger from the electrical outlet and from the

negative and positive battery posts (Fig. 6).

5. Slowly pour electrolyte into each cell until the

level is once again up to the “UPPER” line on

the battery case (Fig. 5).

6. Install the battery and battery box in the tractor:

refer to the Operator’s Manual, Installing the

Battery.

Fill Crankcase with Oil

The tractor is shipped from the factory without oil in

the engine crankcase: refer to the Operator’s Manual,

Engine Oil Specifications for oil type, viscosity, and

crankcase capacity. Only add about 80% of the

specified amount of oil. Then check the oil level and

add only enough oil to raise the level to the “FULL”

mark on the dipstick.

Lubricate the Tractor

Refer to the Operator’s Manual, Greasing and

Lubrication.

Insert Key into Switch

Check Safety System

Refer to the Operator’s Manual, Checking Safety

System.

Set-Up Instructions

Purge Hydro Transaxle

During handling and shipping air can be introduced

into the hydro transaxle. To achieve proper

performance all trapped air must be removed.

1. Place tractor on a flat level surface.

2. Place the drive control, under rear frame. to the

“Push” position (Fig. 7).

21791

Figure 7

1. Operateposition 2. Push position

3. Run engine at a low idle and move traction

control pedal forward for five (5) seconds then

reverse for five (5) seconds. Repeat three (3)

times.

4. Place the drive control in the “Operate” position

(Fig. 7). Drive the tractor forward then reverse

approximately five (5) feet. Repeat three (3)

times.

Check Hydro Neutral Position

Adjustment is required if the tractor creeps without

the traction control pedal being depressed.

1. Run engine at a low idle and move traction

control pedal forward, then release. Move

traction control pedal reverse, then release. If the

tractor creeps adjust as follows:

2. Raise the rear wheels off the ground and support

with jackstands.

3. Loosen locknut securing adjustment (Fig. 8).

4. Move adjustment stud up or down until creep is

minimized (Fig. 8). There may sill be some

wheel rotation with wheels off the ground.

5. Tighten the locknut (Fig. 8). Move the traction

control pedal forward and reverse and allow it to

center. Verify that there is still no creep with the

wheels on the ground.

1673

Figure 8

1. Locknut

2. Stop

Set-Up Instructions

Check Traction Control Pedal

After adjusting the hydro neutral position it is

necessary to check the traction control pedal travel.

While pressing the control pedal full forward and full

reverse it must not contact the footrest pad before

hitting the stop(s) at the transaxle (Fig. 8).

1. If contact is made with the foot pad in either

direction, forward or reverse, adjustment is

required.

2. Loosen the capscrews below the right footrest.

Slide the pedal in the slots away from the

direction that made contact with the footrest

(Fig. 9).

3. Tighten capscrews and recheck traction control

pedal for contact with footrest.

Figure 9

1. Traction control pedal 2. Adjusting capscrews

Test Drive the Tractor

Make sure all electrical and mechanical systems are

operating properly.

Inhaltsverzeichnis

Andere Toro Rasenmäher Handbücher

Toro

Toro Groundsmaster 4000 Bedienungsanleitung

Toro

Toro Titan MR 4800 Bedienungsanleitung

Toro

Toro 03410TE Bedienungsanleitung

Toro

Toro Recycler 20012 Bedienungsanleitung

Toro

Toro GrandStand 74583 Bedienungsanleitung

Toro

Toro 74593 Bedienungsanleitung

Toro

Toro 30402 Bedienungsanleitung

Toro

Toro Groundsmaster 360 Bedienungsanleitung

Toro

Toro Recycler 21311 Bedienungsanleitung

Toro

Toro TurfMaster 22205TE Bedienungsanleitung

Toro

Toro TITAN 121-5680 Bedienungsanleitung

Toro

Toro ProLine 22158 Bedienungsanleitung

Toro

Toro 74806 TimeCutter ZX525 Bedienungsanleitung

Toro

Toro 03180 Bedienungsanleitung

Toro

Toro Greensmaster 3000 Series Bedienungsanleitung

Toro

Toro Greensmaster Fixed Head Walk Behind Series Bedienungsanleitung

Toro

Toro Z Master G3 Handbuch

Toro

Toro TimeCutter Z Handbuch

Toro

Toro TimeCutter SS 4260 Bedienungsanleitung

Toro

Toro Greensmaster Flex 1018 Bedienungsanleitung

Toro

Toro Greensmaster TriFlex 3400 Series Bedienungsanleitung

Toro

Toro eTimeMaster 21491 Bedienungsanleitung

Toro

Toro Z Master 74901 Bedienungsanleitung

Toro

Toro Recycler 20952 Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Stihl

Stihl RMA 443 PV Bedienungsanleitung

Yard-Man

Yard-Man 3700-0 Bedienungsanleitung