Toshiba B-SX6T Series Bedienungsanleitung
PRINTED IN JAPAN
TOSHIBA Thermal Printer
B-SX6T/SX8T SERIES
Document No. EO15-33002
Original Mar., 2006
(Revised )
O
p
tion Installation Manual
EO15-33002
TABLE OF CONTENTS
Page
1. Cutter Module: B-SX208-QM-R-------------------------------------------------------------------------------1- 1
2. Strip Module: B-SX908-H-QM-R -----------------------------------------------------------------------------2- 1
3. Ribbon Saving Module: B-SX908-R-QM-R ---------------------------------------------------------------3- 1
4. Wireless LAN Module: B-SA704-WLAN-QM-------------------------------------------------------------4- 1
5. Serial Interface Board: B-SA704-RS-QM-R --------------------------------------------------------------5- 1
6. Real Time Clock: B-SA704-RTC-QM-R --------------------------------------------------------------------6- 1
7. Expansion I/O Board: B-SA704-IO-QM-R-----------------------------------------------------------------7- 1
CAUTION!
1. This manual may not be copied in whole or in
p
art without prior written permission of TOSHIBA
TEC.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorised Service representative with regard to any queries you
may have in this manual.
Copyright © 2006
by TOSHIBA TEC CORPORATION
A
ll Rights Reserved
570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
1. Cutter Module: B-SX208-QM-R
1- 1
INSTALLATION PROCEDURE FOR OPTIONAL
EQUIPMENT
1. Cutter Module: B-SX208-QM-R
B-SX208-QM-R is an optional cutter module for the B-SX6T/SX8T Series.
•Packing List
The following parts are supplied with the kit. Make sure you have all items shown below.
Cutter Unit (1 pc.)
Cutter Module Cover
(1 pcs.)
Cutter Harness (1 pc.) Cutter Support Plate
(1 pc.)
Print Head Cleaner
(1 pc.)
Cutter Attaching
Screw (2 pcs.)
FL-4x6 Screw (2 pcs.)
SM4x6 Screw (1 pc.) Installation Manual
(1 copy)
Note: for how to use the print head cleaner, please refer to the Owner’s Manual.
•Installation Procedure
1. Turn the power off.
2. Open the right side cover and top covers.
WARNING!
1. Turn the printer power off and disconnect the power cord before installing an optional
equipment.
2. Be careful not to pinch your fingers or hands with the covers.
3. Be careful not to injure your fingers when installing the cutter module.
Top Cover
Right Side Cover
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
1. Cutter Module: B-SX208-QM-R
1- 2
3. Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover.
4. Remove the four FL-4x6 screws to detach the front cover.
5. Remove the SM-4x8 screw and operation panel harness to detach the operation panel.
FL-4x6 Screw
B-3x8 Screw
B-4x6 Scre
w
FL-4x6 Screw
FL-4x6 Scre
w
FL-4x6 Scre
w
SM-4x8 Screw
Operation Panel Harness
Operation Panel
B-4x6 Scre
w
Left Side Cove
r
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
1. Cutter Module: B-SX208-QM-R
1- 3
6. Attach the cutter support plate to the main frame with the two screws (FL-4x6).
7. Connect the cutter harness to CN3 on the cutter interface PC board through the opening of the cutter
unit.
8. Install the cutter unit with the supplied four screws (cuter attaching screws, SM-4x6 and FL-4x6). When
installing the cutter unit, make sure that the cutter guide does not contact with the platen. If so, a print
failure or noise may occur.
FL-4x6 Screw
FL-4x6 Scre
w
Cutter Support Plate
Main Frame
Cutter Interface PC Board
CN3
Cutter Unit Cutter Harness
Cutter Unit FL-4x6 Screw
SM-4x6 Screw
Cutter Attaching Scre
w
Opening
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
1. Cutter Module: B-SX208-QM-R
1- 4
9. Connect the cutter harness to the connector on the printer through the opening of the main frame.
10. Mount the cutter cover with the two screws.
Fit the cutter cover into the cutter attaching screws and secure the cutter cover with the two screws.
11. Attach the operation panel and the left side cover on the printer.
12. Close the top cover and right side cover.
13. After the reassembly is completed, perform a test print to confirm that the cutter works properly.
If the print start position becomes misaligned when media is fed in the reverse direction, fine adjust
the back feed value using the Back Feed Fine Adjustment procedure in system mode.
Cutter Harness
Connecto
r
Main Flame
Screw
Cutter Attaching
Screw
Opening
Cutter Cove
r
Screw
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
1. Cutter Module: B-SX208-QM-R
1- 5
•Adjusting the Cutter Guide Plates
After attaching the cutter unit the following adjustment procedure should be employed to prevent paper
jams.
1. Attach the cutter guide plate A with the two SM-4x6C screws so that the fixed cutter is positioned
0.1 mm to 0.4 mm above the bottom of the cutter guide plate A.
2. Attach the cutter guide plate B with the two FL-4x8 screws so that there is a clearance of 0.5 mm
between the cutter guide plate A and cutter guide plate B using a clearance gauge.
• Media loading procedure------------- Owner’s Manual, Section 2.4
• Operation check------------------------Owner’s Manual, Section 2.10
• System mode setting------------------System Mode Manual
• Cleaning --------------------------------- Owner’s Manual, Section 4.1.5
Cutter Guide Plate B
Cutter Guide Plate A
Screw
(FL-4x8)
Fixed Cutte
r
Screw
(SM-4x6C)
0.1 to 0.4 mm
0.5 mm
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
2. Strip Module: B-SX908-H-QM-R
2- 1
2. Strip Module: B-SX908-H-QM-R
B-SX908-H-QM-R is an optional strip module for the B-SX6T/SX8T Series.
•Packing List
The following parts are supplied with the kit. Make sure you have all items shown below.
Strip Unit (1 pc.)
Strip Harness (1 pc.)
Installation Manual (1 copy)
•Installation Procedure
1. Turn the power off.
2. Open the right side cover and top cover.
3. Remove the six screws (B-4x6, FL-4x6 and B-3x8) to detach the left side cover.
Top Cover
Right Side Cover
FL-4x6 Screw
B-3x8 Screw
B-4x6 Scre
w
B-4x6 Scre
w
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
2. Strip Module: B-SX908-H-QM-R
2- 2
4. Remove the four FL-4x6 screws to detach the front cover.
5. Remove the SM-4x8 screw and operation panel harness to detach the operation panel.
6. Connect the strip harness to CN5 on the PWM PC Board through the opening of the strip base.
FL-4x6 Screw
FL-4x6 Scre
w
FL-4x6 Scre
w
SM-4x8 Screw
Operation Panel Harness
Operation Panel
Strip Unit Strip Harness
Strip Base
PWM PC Board
Opening
CN5
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT
EO15-33002
2. Strip Module: B-SX908-H-QM-R
2- 3
7. Install the strip unit into the printer with the four FL-4x6 screws which were removed in step 4.
8. Connect the strip harness to the connector on the printer through the opening of the main frame.
9. Attach the operation panel and the left side cover on the printer.
10. Close the top cover and right side cover. After that, perform an operation check for a proper strip issue.
• Media loading procedure------------- Owner’s Manual, Section 2.4
• Operation check------------------------Owner’s Manual, Section 2.10
• System mode setting------------------System Mode Manual
• Cleaning --------------------------------- Owner’s Manual, Section 4.1.6
FL-4x6 Screw FL-4x6 Screw
FL-4x6 Scre
w
Strip Unit
Connecto
r
Opening
Main Frame
Strip Harness
Andere Handbücher für B-SX6T Series
4
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Toshiba Drucker Handbücher
Toshiba
Toshiba 4679 Bedienungsanleitung
Toshiba
Toshiba TRST-A00 SERIES Bedienungsanleitung
Toshiba
Toshiba es525p Bedienungsanleitung
Toshiba
Toshiba TRST-A10 SERIES Bedienungs- und Wartungsanleitung
Toshiba
Toshiba E-STUDIO2323AM Bedienungsanleitung
Toshiba
Toshiba B-570 Bedienungsanleitung
Toshiba
Toshiba e-STUDIO 305CP Bedienungsanleitung
Toshiba
Toshiba TRST-A1 Series Bedienungsanleitung
Toshiba
Toshiba TRST-A10 SERIES Bedienungsanleitung
Toshiba
Toshiba B-415 Bedienungsanleitung
Toshiba
Toshiba TRST-A10 SERIES Bedienungsanleitung
Toshiba
Toshiba e-STUDIO GL-1010 Bedienungsanleitung
Toshiba
Toshiba SureMark 4610 Bedienungsanleitung
Toshiba
Toshiba e-STUDIO2010AC Programmierhandbuch
Toshiba
Toshiba B-SA4TP SERIES Bedienungsanleitung
Toshiba
Toshiba TRST-A10 SERIES Bedienungsanleitung
Toshiba
Toshiba B-SX4T Series Bedienungsanleitung
Toshiba
Toshiba TEC B 452 Stücklistenhandbuch
Toshiba
Toshiba B-EV4 Series Bedienungsanleitung
Toshiba
Toshiba SureMark 4610 Bedienungsanleitung
