Toshiba Carrier RBC-AMS41UL Bedienungsanleitung

REMOTE CONTROLLER FOR AIR CONDITIONER (SPLIT TYPE)

Owner’s Manual

Remote controller 2

English

Manuel du proprietaire

Télécommande 26

Français

Remote Controller

Model name:

Remote controller with

weekly timer

RBC-AMS41UL

+00EH99677901_01EN_OM_Remo_Weekly_UL.book Page 1 Thursday, October 8, 2009 2:03 PM

Remote controller with weekly timer Owner’s Manual

–2–

Contents

1 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 PARTS AND THEIR FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 5

3 SETTING THE CURRENT DAY OF THE WEEK AND CLOCK

TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 CORRECT OPERATING PROCEDURES . . . . . . . . . . . . . . . . . . . 9

5 SCHEDULED OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

6 TIMER OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

7 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

8 SELECTING THE REMOTE CONTROLLER FUNCTIONS . . . . . 24

1-EN

+00EH99677901_01EN_OM_Remo_Weekly_UL.book Page 2 Thursday, October 8, 2009 2:03 PM

Remote controller with weekly timer Owner’s Manual

–3–

1SAFETY PRECAUTIONS

• Before use, read carefully through the “Safety Precautions” section to ensure correct

operation.

• The precautions described here are divided into two categories, WARNING and

CAUTION. Both categories contain important safety-related information, and their

directions must be followed without fail.

After reading these instructions, be sure to keep them in a safe place where they can be

referred to at any time by the user. Also be sure that they are handed over to a new user.

Installation precautions

WARNING

•Do not attempt to install the air conditioner yourself.

Ask your dealer or a contractor with specialized experience to install the air conditioner.

Electric shocks and/or a fire may result if you attempt to install the air conditioner yourself

and the air conditioner ends up not being installed perfectly.

•Use only with the authorized air conditioner units.

Be absolutely sure to use only the authorized air conditioner units designated by the

manufacturer.

Also, ask a contractor with specialized experience to install them. Electric shocks and/or

a fire may result if you attempt to install the parts yourself and the parts end up not being

installed perfectly.

CAUTION

•Do not install the remote controller unit where there are high levels of moisture,

oils, grease or vibration.

Failure to heed this caution may cause trouble.

•Do not install the remote controller unit in direct sunlight or near a heat source.

Failure to heed this caution may cause malfunctioning.

•Do not install the remote controller unit where there are sources of noise.

Failure to heed this caution may cause unintended operation.

2-EN

+00EH99677901_01EN_OM_Remo_Weekly_UL.book Page 3 Thursday, October 8, 2009 2:03 PM

Remote controller with weekly timer Owner’s Manual

–4–

Operating precautions

WARNING

•Do not operate the buttons with wet hands.

Failure to heed this warning may result in electric shocks and/or trouble.

•Do not get the control unit wet.

Take steps to avoid getting the control unit wet. Failure to heed this warning may result

in electric shocks, a fire and/or trouble.

•If trouble (such as the smell of burning) has occurred, stop operation and turn off

the circuit breaker.

Allowing operation to continue while the trouble has not been remedied may cause

electric shocks, a fire and/or trouble. Consult your dealer.

CAUTION

•Do not drop the product or subject it to strong impact.

Failure to heed this caution may cause malfunctioning.

•Use only the fuses with the correct amperage.

Use of pieces of wire including copper wiring may cause a fire and/or trouble.

Relocation and repair precautions

WARNING

•Do not undertake any repair work yourself.

Under no circumstances must you attempt to do any repair work yourself.

Instead, consult your dealer or a contractor with specialized experience. Electric shocks

and/or a fire may result if you attempt to do repair work yourself and this work ends up

not being carried out perfectly.

•Consult your dealer when the control unit is to be relocated and re-installed.

3-EN

+00EH99677901_01EN_OM_Remo_Weekly_UL.book Page 4 Thursday, October 8, 2009 2:03 PM

Remote controller with weekly timer Owner’s Manual

–5–

2PARTS AND THEIR FUNCTIONS

LCD area

All displays are shown lighted only for the purposes of description.

1Operation mode display

The selected operation mode is displayed.

2Air direction

This indicates the air direction which has been

selected.

3Fixed louvers

This appears when the louvers are fixed.

* It also appears when the remote controller

function has been selected.

4Filter

This appears when it is time to inspect the

filter.

5Grille up/down

This appears when the grille is goes up or

goes down.

6Self-cleaning operation

This appears while self-cleaning is underway.

7Defrosting

This appears while defrosting is underway

during a heating operation.

8Ready

This display appears on some models.

9Heating ready (indoor fan stops while

this is displayed)

This appears before a heating operation

starts or while defrosting.

No function

This appears when a button is pushed but

there is no corresponding function.

FROST PROTECT operation

This appears during a frost protection

operation.

Numeric display

This displays the numeric value of the

temperature, the numerical order of the

trouble history events or the code numbers

when the functions are set.

Remote control sensor

This appears when the remote control sensor

is used.

Indoor temperature

This appears when the intake temperature is

displayed on the numeric display.

Set temperature

This appears when the set temperature is

displayed on the numeric display.

Central control

This appears when key operation limits are

being enforced by the central controller or

other unit or when key operation limits have

been set in the program for the scheduled

operation currently being executed.

131 2 3 4 5 6 7 8 9 10

22232425

21 20 19 18 17 16 15 14

4-EN

+00EH99677901_01EN_OM_Remo_Weekly_UL.book Page 5 Thursday, October 8, 2009 2:03 PM

Remote controller with weekly timer Owner’s Manual

–6–

Save operation

This appears while a save operation is being

set or executed.

Ventilation operation

This appears while the ventilation fan is

operating.

Numeric display

The numbers of the indoor units or numbers of

the scheduled operation programs are

displayed here.

Air speed display

This indicates the selected air speed.

TEST

This appears while a test run operation is

being performed.

SETTING

This appears when the clock time, a program

or the timer is being set.

ERROR

This appears when there is an error in the

program setting input.

Servicing

This appears during servicing.

Inspect

This appears when trouble has occurred.

Timer function display

This indicates the function whose operation

has been scheduled when a scheduled

operation or timer operation has been set.

Numeric display

This indicates the present clock time, program

operation time or timer execution time.

Operation reservation

This appears for the days of the week on

which programs have been set.

Days of the week display

Special holiday

This appears for a day of the week which has

been set as a special holiday.

Day arrow

This indicates the current day of the week or

day on which a program is set.

5-EN

+00EH99677901_01EN_OM_Remo_Weekly_UL.book Page 6 Thursday, October 8, 2009 2:03 PM

Remote controller with weekly timer Owner’s Manual

–7–

Button operation area

ON/OFF button

Shortly after this button is pushed, operation

starts, and operation stops shortly after the

button is pushed again.

FAN button

Use this to select the desired air speed mode.

MODE button

Use this to select the desired operation mode.

VENT button

Use this when a ventilation fan or other unit,

purchased on the market, has been

connected.

LOUVER button

Use this to select the louvers when setting the

air direction for each louver or when fixing the

louvers in place.

UNIT button

Use this to select the indoor unit to be

operated when operating a multiple number of

indoor units using one remote controller.

SAVE button

Use this when performing save operations.

SWING/FIX button

Use this to select the desired air direction or

swing operation.

TIME buttons

Use this to set the clock or adjust the time

when the operating time is set.

CL button

Use this when clearing the setting of the

program (for a scheduled operation or timer

operation) which is being set.

SET button

Use this when entering the settings of the

program (for a scheduled operation or timer

operation) which is being set.

TEST button

Use this for servicing.

* This button is not normally used.

FLT.RESET button

Use this to reset (extinguish) the filter display.

DAY button

Use this to select the targeted day of the week

when setting the clock or setting a program.

PROGRAM button

Use this when starting and ending the

program settings for scheduled operations.

Grille button

Use this to raise or lower the grille.

SCHEDULE button

Use this when executing or releasing

scheduled operations or when selecting ON

or OFF for timer operations.

TEMP. buttons

Push and to set the temperature to

the desired value.

* These buttons are also used to raise or

lower the grille when the grille function is

used.

ON lamp

This lights during operation. It blinks when

trouble has occurred or when a protection

operation is performed.

424344

49 50

6-EN

+00EH99677901_01EN_OM_Remo_Weekly_UL.book Page 7 Thursday, October 8, 2009 2:03 PM

Remote controller with weekly timer Owner’s Manual

–8–

3SETTING THE CURRENT DAY OF THE WEEK

AND CLOCK TIME

• Set the current clock time and day of the

week.

• The day of the week and clock settings

can be performed whether the air

conditioner is running or shut down.

* The air conditioner continues to operate

(run) while the day of the week and

clock settings are being performed.

• The normal operation of the air conditioner

or a program for a scheduled operation

can be input even without performing the

day of the week and clock settings, but the

scheduled operation cannot be executed.

In order to execute scheduled operations,

the day of the week and clock must be set

without fail.

• Before this remote controller is shipped

from the factory, the initial setting (default)

of the 24-hour display is established for

the clock time display, but this can be

changed to the 12-hour (AM/PM) display.

* If you want to use the 12-hour time

display, refer to the “Selecting the

remote controller functions” section.

* In these instructions, the 24-hour

display is used in the figure and

descriptions.

Preparations

Turn on the ground fault interrupter.

• When the power is turned on, a dividing

line appears on the remote controller

display.

* For about a minute after the power has

been turned on, on the LCD

screen blinks, and there will be no

response to the keys of the remote

controller even when they are pushed.

1Hold down the button

(48) for at least 4

seconds.

• The display transfers to the

day of the week/clock

setting screen.

• The whole LCD display blinks.

2Repeatedly push the button (45),

and select the current day of the

week.

• Move the day arrow to the position

above the current day of the week.

• The LCD display continues to blink.

3Push the TIME and buttons

(40), and select the current clock time.

• Each time the button (40) is pushed,

the clock is moved forward by one minute.

• Each time the button (40) is pushed,

the clock is moved back by one minute.

• When the or button is held down,

the clock is moved forward or back in 10-

minute increments.

• The LCD display continues to blink.

4Push the button (42) to return to the

original screen.

• As soon as the button is pushed, the clock

starts running. (Do this in synchronization

with a time signal.)

• on the LCD screen goes off.

• After the clock has been set, the entire LCD

screen lights, but the colon (“:”) continues

to blink.

SETTING

SETTING

7-EN

+00EH99677901_01EN_OM_Remo_Weekly_UL.book Page 8 Thursday, October 8, 2009 2:03 PM

Remote controller with weekly timer Owner’s Manual

–9–

4CORRECT OPERATING PROCEDURES

Procedure for normal

operation

The functions will differ depending on the

model and system.

• Follow the steps below before using the

remote control system for the very first

time or when changing any of the settings.

• After the steps have been followed,

operation will commence using the

settings established simply by pushing the

button (32).

Preparations

Turn on the ground fault interrupter.

• When the power is turned on, a dividing

line appears on the remote controller

display.

* For about a minute after the power has

been turned on, on the LCD

screen blinks, and there will be no

response to the keys of the remote

controller even when they are pushed.

NOTE

• Do not turn off the ground fault interrupter

during the operating season of the

remote control system.

• After the remote control system has been

shut down for a prolonged period, turn on

the ground fault interrupter back on at

least 12 hours before its operation is to

be started.

Starting operation

1Push the button (32) to start

operation.

• The ON lamp lights, and the operation

details are displayed on the LCD screen.

2Push the button (34), and select

the mode of operation.

• Each time this button is pushed, the

operation mode display changes in the

sequence shown below.

• Stop pushing the button when the symbol

corresponding to the desired mode of

operation lights.

3Push the button (32) to shut

down operation.

• The ON lamp goes off, and the operation

details are cleared from the LCD screen.

(The frame lines remain displayed.)

• Before operation shuts down, the self-

cleaning operation is commenced if the air

conditioner was run in the Auto (during

cooling), cooling or dry mode for 10 or

more minutes.

* For details on the self-cleaning

operation, refer to the “Self-cleaning

operations” section.

SETTING

Auto Heating

Fan Cooling Dry

8-EN

+00EH99677901_01EN_OM_Remo_Weekly_UL.book Page 9 Thursday, October 8, 2009 2:03 PM

Remote controller with weekly timer Owner’s Manual

–10–

Changing the air speed

1Push the button (33), and select

the desired air speed.

• Each time the button is pushed, the air

speed display changes in the sequence

shown below.

• Stop pushing the button when the symbol

corresponding to the desired air speed

lights.

* If, during heating, the rooms do not heat

up quickly at the low air speed setting,

change the setting to high or medium.

* The auto air speed cannot be selected

during fan operations.

Changing the temperature

1Push the TEMP. and buttons

(49), and select the desired

temperature setting.

• When the button (49) is pushed, the

temperature on the numeric display goes

down; conversely, when the button

(49) is pushed, the temperature displayed

goes up.

• The temperature cannot be set during fan

operations.

Adjusting the air direction

The functions will differ depending on the

model and system.

• To increase the cooling or heating effect,

be sure to change the louver direction

between cooling and heating operations.

• The nature of air is to fall toward the floor

where it collects when it is cold and to rise

toward the ceiling where it collects when it

is warm.

CAUTION

•For cooling operations, set the

louvers to the horizontal blow-out

position.

Performing cooling operations with the

louvers at the downward blow-out

position may cause condensation to

form around the air outlets and louver

surfaces and water may drip.

* For further details, refer to the

operating instructions of the air

conditioner.

Changing the air direction

1During operation, push the

button (39), and select the desired air

direction.

• Each time the button is pushed, the air

direction display changes in the sequence

shown below.

• Stop pushing the button when the symbol

corresponding to the desired air direction

lights.

* Air directions 4 and 5 are not displayed

during cooling or dry operations.

* It may not be possible to set air direction

1 after the air direction has been at the

random setting.

If this is the case, wait 2 seconds, and

then push the button (39) again.

Starting the louver swing motion

1During operation,

push the button

(39), and select the

symbol shown on the

right.

• If the button is then pushed from the

downward blow-out position, the symbol

shown on the right lights for the air direction

display.

Auto air speed High air speed

Low air speed Medium air speed

12345

Random SWING

9-EN

+00EH99677901_01EN_OM_Remo_Weekly_UL.book Page 10 Thursday, October 8, 2009 2:03 PM

Inhaltsverzeichnis

Andere Toshiba Fernbedienung Handbücher

Toshiba

Toshiba RBC-AMTU31-E Bedienungsanleitung

Toshiba

Toshiba MML-AP0074NH-E Bedienungsanleitung

Toshiba

Toshiba VCR remote Betriebsanleitung

Toshiba

Toshiba Carrier TCB-AX21UL Bedienungsanleitung

Toshiba

Toshiba Carrier TCB-AX21UL Bedienungsanleitung

Toshiba

Toshiba RBC-AMS54E-UL Bedienungsanleitung

Toshiba

Toshiba Lite-Vision plus RBC-AMS51E Bedienungsanleitung

Toshiba

Toshiba RBC-AMS54E-ES Bedienungsanleitung

Toshiba

Toshiba RB-RWS21-E Bedienungsanleitung

Toshiba

Toshiba CT-8002 Bedienungsanleitung

Toshiba

Toshiba Lite-Vision plus RBC-AMS51E-EN Bedienungsanleitung

Toshiba

Toshiba TCB-SC640U-E Bedienungsanleitung

Toshiba

Toshiba RBC-AMS54E Bedienungsanleitung

Toshiba

Toshiba RBC-AX31U-UL Bedienungsanleitung

Toshiba

Toshiba RBC-CR1-PE Bedienungsanleitung

Toshiba

Toshiba RAV Heat Bedienungsanleitung

Toshiba

Toshiba 2358 9721 Bedienungsanleitung

Toshiba

Toshiba RBC-AWSU52-UL Bedienungsanleitung

Toshiba

Toshiba RBC-SR1-PE Bedienungsanleitung

Toshiba

Toshiba RBC-AS21UL Bedienungsanleitung

Toshiba

Toshiba RBC-AX32U(W)-E Bedienungsanleitung

Toshiba

Toshiba TCB-AX21E Bedienungsanleitung

Toshiba

Toshiba TCB-AX21E Bedienungsanleitung

Toshiba

Toshiba RBC-AS21E Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung

JR Racing

JR Racing XR2 Bedienungsanleitung

Philips

Philips SBCRU130/00U Bedienungsanleitung

Philips

Philips Prestigo SRT9320 Bedienungsanleitung

Vicon

Vicon VNCTRL-1 Bedienungsanleitung