Town & Country Fireplaces TC36 Bedienungsanleitung

270904-40 TC36_B 5056.42712

WARNING: If the information in this

manual is not followed exactly, a re or

explosion may result causing property

damage, personal injury or loss of life.

-- Do not store or use gasoline or other

ammable vapours and liquids in the

vicinity of this or any other appliance.

-- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Donottouchanyelectricalswitch;do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbour’s phone. Follow

the gas supplier’s instructions.

• Ifyoucannotreachyourgassupplier,

call the re department.

--Installationandservicemustbeperformed

by a qualied installer, service agency or

the gas supplier.

FOR YOUR SAFETY

IMPORTANT:

THESE INSTRUCTIONS ARE TO

REMAIN WITH THE

HOMEOWNER

INSTALLATION

AND OPERATING

INSTRUCTIONS

MODEL

TC36

SERIES B

DIRECT VENT FIREPLACE

This appliance may be installed in an

aftermarket permanently located, manu-

facturedhome(USAonly)ormobilehome,

where not prohibited by local codes.

This appliance is only for use with the

type of gas indicated on the rating plate.

This appliance is not convertible for use

with other gases, unless a certied kit is

used.

2 TC36_B 270904-40

Contents

CAUTION ..............................................................................................................3

SAFETY ................................................................................................................3

INSTALLATION REQUIREMENTS....................................................................... 5

TOP STANDOFFS................................................................................................. 5

LOCATING THE FIREPLACE ..............................................................................5

FRAMING AND FINISHING .................................................................................. 6

HEARTH EXTENSION.......................................................................................... 8

CONTROL BOX .................................................................................................... 8

CONTROL BOX RELOCATION.......................................................................... 10

VENTING............................................................................................................. 11

WALL TERMINATION VENTING........................................................................ 12

ROOF TERMINATION VENTING .......................................................................16

VENT TERMINAL CLEARANCE ........................................................................ 18

VENT PIPE SEALANT........................................................................................19

INSULATED COLLAR SHIELD ..........................................................................19

VENT RESTRICTOR ADJUSTMENT ................................................................. 20

MANUFACTURED (MOBILE) HOME ................................................................. 20

GAS SUPPLY...................................................................................................... 21

OPTIONAL WALL SWITCH................................................................................ 21

WINDOW FRAME REMOVAL ............................................................................ 22

BRICK PANELS INSTALLATION ....................................................................... 23

EMBER MATERIAL ............................................................................................ 24

LOG SET ASSEMBLY ........................................................................................ 24

LIGHTING INSTRUCTIONS - Millivolt Valve .................................................... 26

FIRST FIRE ......................................................................................................... 26

OPERATING .......................................................................................................26

LIGHTING INSTRUCTIONS - Electronic Valve ................................................ 27

FLAME ADJUSTMENT....................................................................................... 28

MAINTENANCE .................................................................................................. 29

APPENDIX A.......................................................................................................29

REPLACEMENT PARTS.............................................................................. 30

REPLACEMENT PARTS-MILLIVOLT CONTROL ASSEMBLY................... 31

REPLACEMENT PARTS - ELECTRONIC CONTROL ASSEMBLY............ 32

ELECTRONIC VALVE WIRING DIAGRAM.................................................. 33

WALL TERMINATION KIT ........................................................................... 34

WALL SHIELD/CEILING FIRESTOP THIMBLE .......................................... 34

ROOF TERMINATION KIT ...........................................................................35

VENT PIPE DIMENSIONS............................................................................ 36

VENT OFFSET CHART................................................................................ 37

VARIOUS GAS SUPPLY CONNECTIONS................................................... 38

SAFETY LABEL LOCATION........................................................................ 39

270904-40 TC36_B 3

CAUTION

FOR YOUR SAFETY - Do not install or operate your Town

and Country replace without rst reading and understanding

this manual. Any installation or operational deviation from the

following instructions voids the Town and Country FireplacesTM

Warranty and may prove hazardous.

This appliance and its individual shutoff valve must be discon-

nected from gas supply piping system during any pressure

testing of that system at test pressures in excess of 1/2 psig

(3.5 kPa).

This appliance must be isolated from the gas supply piping

system by closing its individual manual shutoff valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psig (3.5 kPa).

Note: When lit for the rst time, the appliance will emit a slight

odour for a couple of hours. This is due to the curing of paints,

sealants and lubricants used in the manufacturing process. This

condition is temporary. Open doors and windows to ventilate

area. Smoke and fumes caused by the curing process may

cause discomfort to some individuals.

Do not use the replace if any part has been under water.

Immediately call a qualied service technician to inspect the

replace and to replace any part of the control system and

any gas control which has been under water.

SAFETY

Due to high temperatures, this gas appliance should

be located out of trafc and away from furniture and

draperies.

Children and adults should be alerted to the hazards of

high surface temperatures and should stay away to avoid

burns or clothing ignition.

Young children should be carefully supervised when they

are in the same room as the appliance.

Clothingorother ammable materialshould notbe placed

on or near the appliance.

Any grill, panel or door removed for servicing the unit

must be replaced prior to operating. Failure to do so

may create a hazardous condition.

Installationandrepairshouldbe done by a qualied service

person. The appliance should be inspected before use

and at least annually by a professional service person.

More frequent cleaning may be required due to excessive

lint from carpeting, bedding material, etc. It is imperative

that control compartments, burners and circulating air

passageways of the appliance be kept clean.

It is our policy that no responsibility is assumed by the

Company or by any of its employees or representatives

for any damages caused by an inoperable, inadequate,

or unsafe condition which is the result, either directly

or indirectly, of any improper operation or installation

procedures.

TOP

STANDOFFS

CENTER OF

FLUE OUTLET

Fig # 1

FIREPLACE DIMENSIONS

4 TC36_B 270904-40

Minimum Clearances to Combustibles:

Side standoffs...................... 0 in. (0 mm)

Back standoffs..................... 0 in. (0 mm)

Top standoffs....................... 0 in. (0 mm)

Bottom of appliance............. 0 in. (0 mm)

Adjacent sidewall................. 4 in. (102 mm)

Ceiling to appliance ........... 24 in. (610 mm)

*Mantel to appliance ..........See Figure #2

**Maximum

Mantel extension ..........See Figure #2

Mantel support..................... 4 in. (102 mm)

Vertical vent pipe........... 1-3/4 in. (45 mm)

Horizontal vent pipe

Top ........................... 1-3/4 in. (45 mm)

Sides ........................ 1-3/4 in. (45 mm)

Bottom ...................... 1-3/4 in. (45 mm)

Fig. # 3

CEILING

ADJACENT

WALL OR

MANTEL

SUPPORT

MANTEL

UNIT MAY BE RECESSED UP TO

6" WITH NON-COMBUSTIBLE

MASONRY TYPE MATERIAL

A 9" D 12"

B 6" E 6 3/4"

C 3" F 1 1/2"

COMBUSTIBLE FRAMING

AND FINISH WALL ABOVE

STANDOFFS

MAY USE COMBUSTIBLE

FACING MATERIAL IN THIS

AREA

NONCOMBUSTIBLE FINISH

MATERIAL

SEE FIG #7

STANDOFFS

STEEL FRAMING

FIREPLACE FRONT

TOP OF LINTEL BAR

MANTEL CLEARANCE CHART

REF. MANTEL

DEPTH

REF.

MANTEL

CLEARANCE

Fig. # 2

***

270904-40 TC36_B 5

INSTALLATION REQUIREMENTS

The Town & Country Fireplace installation and venting

must conform to the current CAN/CGA-B149 installation

code (in Canada) or the current National Fuel Gas Code,

ANSI Z223.1 (in the USA), and approved per local codes.

Only qualied (licensed or trained) personnel should

install this product.

In the state of Massachusetts, only a licensed Plumber

and Gas Fitter may install this product.

Fig. # 4 TOP

STANDOFFS

Fig. # 5 Examples of Common Locations

TOP STANDOFFS

The top standoffs are shipped loose inside the replace and

must be installed on top of the replace as shown in g. #4.

Do this once the replace is on site and in position.

LOCATING THE FIREPLACE

In planning the installation for the replace, it is necessary to

determine where the unit is to be installed, location of vent

system and where gas supply piping may be plumbed. Vari-

ous installations are possible, such as, into an existing wall,

a corner, a built-in wall or a wall projection (see Fig. #5). Due

to high temperatures, do not locate this replace in areas of

high trafc or near furniture or draperies.

The minimum clearances from the replace to combustible

surfaces are shown on Fig. # 2 and 3.

CAUTION: When selecting a location, ensure

that there is adequate room on the right hand

or left hand side of the replace for the control

box.

6 TC36_B 270904-40

FRAMING AND FINISHING

Note: The replace must be in place and venting installed

before framing in or building an enclosure around the

unit.

The Town & Country Fireplace may be framed in with build-

ing materials (wood and steel studs) or totally enclosed with

non-combustible material, such as facing brick.

Determine the total thickness of facing material to be used.

A total thickness of 3/4" will allow the nishing surface to be

ush with the front of the unit. If preferred, additional masonry

type non-combustible material can be installed above and to

the sides up to 6 inches proud of the appliance.

Once the replace is in its nal position, frame metal studs to

the insides of the framing brackets on each side of the unit.

Ensure that the studs are set back far enough to allow for

thickness of nishing surface. Secure replace to steel studs

with screws. Frame in a steel header directly above the lintel

bar. Additional steel support studs can be added above the

header up to the ceiling.

The sides, back and top of the replace can be framed in

up to the standoffs using conventional 2 x 4 lumber. Heavier

construction may be required for some installations, consult

local building codes for specic requirements.

Due to high temperatures, concrete board (or other non-

combustible material) must be used to sheet in the front of

the replace, extending 12" above and 1 1/2" to the side of

the framing edge bars. See gure #8. Standard sheetrock

(drywall) may be used beyond this.

Chase Insulation: When installing this replace against a

non-insulated exterior wall or chase, it is recommended that

the outer walls be insulated to same degree as other exterior

walls. Do not place replace directly against the insulation.

Cover the insulation and plastic vapour barrier with a solid

surface, such as drywall (sheetrock). Consult local codes.

Fig. # 6

STEEL

HEADER

STEEL

STUDS

FRAMING

BRACKETS

MINIMUM

STEEL STUD FRAMING

DETAIL

ALL OTHER FRAMING

CAN BE DONE WITH

CONVENTIONAL 2X4

LUMBER

Concrete board (or other non-combus-

tible material) must extend 12" above

and 1 1/2" to the sides of the framing

edges.

CONCRETE

BOARD

MINIMUM

CONCRETE BOARD

DETAIL

Fig. # 7

270904-40 TC36_B 7

OPTIONAL STEEL STUD FRAM-

ING KIT DIMENSIONS

(TC36.BFRKITA)

* 48" if framed using the Optional

Steel Stud Framing Kit (g. #8)

41 1/2" if the replace is framed in

place to the minimum steel stud

requirements (g. #7)

Fig. # 8

3/4"

54 1/2"

27 3/8"

19 3/8"

54 1/2" *

Fig. # 10 MINIMUM COMBUSTIBLE FRAMING DIMENSIONS

WARNING: Framing dimensions will vary with location of

replace, which may need to be adjusted to accommodate

control box placement and vent installation. Fireplace should

be in it's nal location before framing.

NON-COMBUSTIBLE RECESSED

INSTALLATION DETAIL

CONCRETE

BOARD

STEEL

STUDS

NON-COMBUSTIBLE

MASONRY TYPE

MATERIAL

Fig. # 9

CAUTION:

When framing

for the replace,

ensure adequate

space is provided

for the control box.

Do not install the

control box above

the replace.

Including Sheetrock

48 1/4"

*3/4"

23 3/8"

11 1/8"

48"

8 TC36_B 270904-40

MAX

HEARTH EXTENSION

While a hearth extension is not required

for this replace, one is recommended

for aesthetic reasons. The hearth

extension should be noncombustible

and must not be any more than 1"

above the bottom of the replace. If

thicker, replace must be raised up

accordingly.

Caution: Hearth extensions thicker

than1"willinterferewith the window

frame.

CONTROL BOX

The gas control system is housed in a control box remote of

the replace. Flexible conduits attach the control box to the

replace and house all the plumbing and wiring to the burner.

This unique design allows the control box to be mounted in

a variety of positions on the right or left side of the replace.

The box can be framed into the front right or left face or the

right or left sidewall of the replace enclosure. As the control

system is attached at the factory to exit the right side of the

replace, please see "Control Box Relocation" section to move

the control box to exit the left side.

Caution: When positioning the control box, do not over

bend the conduit or use excessive force, as damage may

occur.

1) Remove window frame latch tool and set aside.

2) Remove 4 screws holding control panel in place and

carefully lift off over the control knobs, being sure not to

damage wires and connections to the "Pilot Flame" indi-

cator (millivolt control system only). Carefully disconnect

wires from indicator, and set aside.

3) Attach control box to framing at predetermined depth,

allowing room for wall nishing material. Side brackets

can be adjusted for a trim t.

4) Attach control box to framing at predetermined depth,

allowing room for wall nishing material. Side brackets

can be adjusted for a trim t.

6) Replace door/inner frame assembly and fasten in place.

Note: Gas supply plumbing must be completed and the

spark igniter battery or backup batteries installed before

reinstalling the front control panel.

Fig. # 11

PILOT

FLAME

INDICATOR

CONTROL

DOOR AND

FRAME

GAS

VALVE

BURNER

SWITCH

CONDUIT

BATTERY SPARK

IGNITER

MANUAL MILLIVOLT VALVE

6) Reconnect "Pilot Flame" indicator wiring and reinstall

control panel.

WINDOW

FRAME

HEARTH

EXTENSION WINDOW

TRACK

SUB-

FLOOR

Fig. # 12

270904-40 TC36_B 9

9 3/8"

12"

4 1/4"

CONTROL BOX LOCATION AND

FRAMING DETAIL

Fig. # 13

CAUTION:

- A 2 foot service access clearance is recom-

mended in front of the control box.

- If recessed into a masonry wall, allow for

control door and frame removal.

- If ush mounted on a masonry wall, allow for

conduit to exit out the bottom of control box.

POSSIBLE CONTROL BOX

LOCATIONS LEFT OR RIGHT

OF THE FIREPLACE

Caution: When posi-

tioning the control box,

do not over bend the

conduit or use exces-

sive force, as damage

may occur.

Alternately, the

controlmay bere-

positioned from

the right side of

the fireplace to

the left side.

10 TC36_B 270904-40

CONTROL BOX RELOCATION

1) Remove glass, logs; grate assembly and rebox panels

if installed.

2) Disconnect ex gas line from the manifold assembly.

3) Remove 2 screws holding pilot bracket to burner pan.

4) Remove 2 screws holding pilot assembly to pilot

bracket.

5) Remove 4 screws holding inlet box to rebox.

6) Pull pilot assembly and plumbing through rebox side,

taking care not to damage pilot, plumbing or wires.

REMOVE PILOT BRACKET

FROM BURNER ASSEMBLY

REMOVE SCREWS HOLDING INLET BOX

REPOSITION MANIFOLD

Fig. # 14

Fig. # 17

Fig. # 15

PULL OUT CONTROL ASSEMBLY

Fig. # 16

Andere Handbücher für TC36

Inhaltsverzeichnis

Andere Town & Country Fireplaces Kamin im Innenbereich Handbücher

Town & Country Fireplaces

Town & Country Fireplaces TC36.CSTE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54NG04.C2 Technisches Handbuch

Town & Country Fireplaces

Town & Country Fireplaces TC36 TC36ST.NGST03D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Gebrauchsanweisung

Town & Country Fireplaces

Town & Country Fireplaces TC42.NG04C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54CE SERIES C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54NG04.C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces D Series Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCVT.FMPV3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30.CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch