Town & Country Fireplaces TCWS38 Bedienungsanleitung

OPTIONAL

VERTICAL OR

HORIZONTAL

POWER VENT KIT

TCVT.PVB1

INSTALLATION AND

OPERATING

INSTRUCTIONS

110509-12 TCVT.PVB1 5056.4265.B1

5 x 8 Pipe

(Simpson Duravent)

(Secure Vent)

(Selkirk Direct-temp)

(not supplied.)

These instructions are supplementary to the Installation and

Operating Instructions supplied with the replace and should

be kept together. Refer to the Installation and Operating

Instructions for proper gas supply, safety requirements and

operating instructions

Power Vent Terminal

Vent Adaptor

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Wall Thimble

(not supplied)

fire-parts.com

110509-12 TCVT.PVB1

Locate the replace as per the main instructions supplied.

Make the following modications to add the components used with the Power Vent

Kits. This Kit can only be used in conjunction with the “B” & “C” series versions of

Town and Country replaces. This installation must conform with local codes or, in

the absence of local codes, with the Natural Fuel Gas Code, ANSI Z223.1/NFPA 54,

or the Natural Gas and Propane Installation Code, CSA B149.1.

All electrical installation should be performed by a qualied electrician to national

codes (CSA C22.1, ANSI/NFPA 70) and/or local electrical codes.

ITEM PART No. DESCRIPTION QTY

1 TCVT.502461 Power Vent Terminal 1

2 5096.813 Venting Adaptor 1

3 TCVT.506271C Pressure Switch Wiring 1

4 5027.15 Pressure Switch 1

5 8024 Tubing, TYSC-516316-100 2

6 5093.01 Hose Clamp 2

7 5093.02 Hose Clamp 2

8 TCVT.507156C Power Vent Switch Wire 1

MINIMUM CLEARANCES TO

COMBUSTIBLE

Vertical vent pipe:

1.5 in. (38mm)

Horizontal vent pipe:

Top 1.5 in. (38mm)

Sides 1.5 in. (38mm)

Bottom 1.5 in. (38mm)

All other clearances are as per the replace

installation instructions.

VENTING CONFIGURATIONS

Maximum vent length is 110 ft

plus six 90-degree elbows or

combination of other elbows

equaling 90-degrees, with a

maximum 66 foot vertical rise.

Minimum vent length is 3 ft

plus one 90-degree elbow.

The vent can be installed

with any combination of rise

and run between the gures

including up to 3 ft below

the unit. Ensure vent pipe is

properly supported.

Maximum Combined

vertical & horizontal

venting -

110 ft plus six

90-degree elbows.

Vertical Application must use TCVT.PVVCA Box in

conjunction with this kit

4 ft min. 6 ft min.

Max. 66 ft

Min. venting - 3 ft plus

one 90-degree elbow

3 ft below unit (Max) to

centerline of vent pipe

Fig. #1

Power Vent

Power Vent Installation

Contents of Power Vent Kit

fire-parts.com

Wall Termination Venting Chart

*TC36 and TC36AR have the same dimensions

TCWS38 TC30 TC36 TC 42 TC36ST

45” 47” 51” 57” 56” 0” 110 feet 3 feet

47” 59” 63” 69” 68” 12” 109 feet 2 feet

69” 71” 75” 81” 80” 24” 108 feet 1 foot

Minimum Rise Pipe Max. Min.

Length Pipe Pipe

Length Length

A B C

110509-12 TCVT.PVB1

Fig. #2

Fig. #1a

Vent Terminal Minimum Clearances

A= clearances above grade, veranda, porch, deck, or balcony [*

12 inches (30 cm) minimum]

B= clearance to window or door that may be opened [* 12

inches (30 cm) minimum]

C= clearance to permanently closed window [minimum 12

inches (30 cm) recommended to prevent condensation on

window]

D= vertical clearance to ventilated soffit located above the ter-

minal within a horizontal distance of 2 feet (60 cm) from the

edge of the terminal [12 inches (30 cm) minimum]

E= clearance to unventilated soffit [12 inches (30 cm) minimum]

F= clearance to outside corner [6 inches (15 cm) minimum]

G= clearance to inside corner [6 inches (15 cm) minimum]

H= * not to be installed above a meter/regulator assembly within

3 feet (90 cm) horizontally from the center-line of the regula-

tor

I= clearance to service regulator vent outlet [* 6 feet (1.8 m)

minimum]

J= clearance to nonmechanical air supply inlet to building or the

combustion air inlet to any other appliance [* 12 inches (30

cm) minimum]

K= clearance to a mechanical air supply inlet [* 6 feet (1.8 m)

minimum]

L= ^ clearance above paved side-walk or a paved driveway

located on public property [* 7 feet (2.1 m) minimum]

M= clearance under veranda, porch, deck, or balcony

[12 inches (30 cm) minimum**]

^ a vent shall not terminate directly above a side-walk or paved driveway which is located between two single family dwellings and

serves both dwellings*

** only permitted if veranda, porch, deck, or balcony is fully open on a minimum of 2 sides beneath the oor*

* as specied in CGA B149 Installation Codes, Note: local Codes or Regulation may require different clearances

* for U.S.A. Installations follow the current National Fuel Gas Code, ANSI Z223.1

AIR SUPPLY INLET

VENT TERMINAL GAS METER

FIXED

CLOSED

FIXED

CLOSED

OPEN-

ABLE

OPEN-

ABLE

INSIDE

CORNER

DETAIL

AREA WHERE TERMINAL

IS NOT PERMITTED

fire-parts.com

Wall Thimble

(Not Supplied)

110509-12 TCVT.PVB1

This kit uses either Simpson Duravent GS direct vent pipe, Secure Vent

direct vent pipe or Selkirk Direct-temp vent pipe with a 5” inner pipe and

an 8” outer pipe. For part numbers see the table of venting components on

page 11 of this manual.

1. Locate the power vent termination following the clearance to combustible table, venting

conguration diagram (Fig. #1 & 1a), and terminal location diagram (Fig. #2).

2. Cut and frame an 11” x 11” opening. The centre of the square hole should line up with

the centre line of the horizontal pipe.

3. Install the Simpson Duravent (or equivalent) Wall thimble, part number 1247 (not

supplied with kit) in the opening to retain any insulation in the wall and maintain proper

clearances. If the wall being penetrated is constructed of noncombustible material only

(i.e.. Masonry block or concrete) the wall thimble is not required and a hole with zero

clearance is acceptable. (8” hole)

4. Attach the terminal to the outside wall. Ensure that the terminal is the right way up and

that only the outer anges that are used to secure the terminal to the building are covered

by the exterior wall or siding. (Fig.#3) Note: No other part of the terminal can be

recessed into the exterior wall or siding.

5. Attach the vent adaptor directly to the appliance with three screws and seal outer pipe

with aluminium tape provided. (Fig. #4)

Note: The inner pipe does not need to be sealed.

6. Connect one of the high temperature silicone tubes to the upper pressure tap on the

adaptor.(Fig. #4) Secure with the hose clamp provided and route the tube through any

hole back to control box. This tube will be connected to the “low” side of the vacuum

switch inside the control compartment. (Fig. #11) Connect the second tube to the lower

pressure tap and route to the control box as before. Connect this tube to the remaining

port on the vacuum switch. Tubes may touch unit and be trimmed if required. Note:

Ensure that there are no blockages in these tubes, as this will cause the control to

malfunction.

7. Run the required Simpson Duravent GS / Secure Vent / Selkirk Direct-temp pipe from

the adaptor to the terminal assembly. Assemble as per the vent pipe manufacturer’s

instructions including all shields and restops.

CAUTION:

The adjustable vent restrictor located

on the underside of the rebox top

must be fully open.

Exhaust

Outlet

Finished

Wall

Power Vent Terminal

Fig. #3 Fig. #4

Power Vent Adaptor.

Part # 5096.813

MUST BE

INSTALLED AT

THE UNIT

UPPER

PRESSURE

TAP

Secure with three

screws

LOWER

PRESSURE

TAP

Horizontal (Side Wall) Venting

fire-parts.com

110509-12 TCVT.PVB1

CAUTION:

The adjustable vent restrictor located

on the underside of the rebox top

must be fully open.

Vertical (Through Roof) Venting

This kit uses either Simpson Duravent GS direct vent pipe, Secure Vent

direct vent pipe or Selkirk Direct-temp vent pipe with a 5” inner pipe and

an 8” outer pipe. For part numbers see the table of venting components on

page 11 of this manual.

Vertical installations must use the optional TCVT.PVVCA vertical adaptor box in

conjunction with this kit. The vertical adaptor box can only be installed on a at surface.

Sloped surfaces require the construction of a chase which provides the minimum interior,

square opening of 11” x 11” for the venting and wiring to pass through. Flat roofs may

require a chase depending on local codes and roof construction. (If in doubt check with

local inspector)

The terminal must be located in accordance with the clearances outlined in Fig. #1 and 2.

Installation:

All part numbers in the following section

are shown in Fig. #5.

1. Place the ashing (Part A) onto the

chase and seal using silicone.

2. Put a bead of silicone on the underside

of the vertical standoff (Part B) and place it

on top of the ashing. Align the eight holes

and secure both parts to the chase using

eight #8 x 1 1/2” screws provided.

3. Install the drip shield (Part C) onto the

top of the vertical standoff using a bead of

silicone between the two. Do not screw this

part in place.

4. Bring the 14-2 electrical wire (not

supplied) up through the holes in both the

ashing and the drip shield leaving at least

12” of excess wire above the drip shield.

5. IMPORTANT: Attach an appropriate

length(s) of the vent to the power vent

terminal, sufficient to pass through the

chase.

NOTE: DO NOT CONNECT AN

ADJUSTABLE LENGTH VENT PIPE TO

THE TERMINAL.

6. Seal the connection of the rst length of

pipe at the terminal and any other pipe to

pipe joint by both screwing and taping the

outside joint using high temperature foil

tape.

7. Remove the junction box cover. (Part D)

8. Remove and discard the exhaust shield.

(Part E)

9. Apply a bead of silicone on the bottom

ange of the power vent terminal.

10. Slide the vent through the drip shield

and at the same time thread the electrical

lead through the hole in the bottom of the

terminal.

11. With the power vent terminal resting

on the drip shield, align the eight holes in

each of the vertical standoff, the drip shield

and the power vent terminal and then

screw them together using the eight #8 x

1/2” stainless screws provided.

12. Join the 14-2 wire lead to the blower

wires using the appropriate connectors

and attach the ground wire. Reinstall the

junction box cover.

13. Install the vertical rain cap (Part F)

over the power vent blower. ALIGN THE

EXHAUST OUTLET ON THE POWER

VENT TERMINAL WITH THE EXHAUST

PORT ON THE VERTICAL RAIN CAP.

14. Secure the vertical rain cap to the

power vent blower with the remaining eight

#8 x 1/2” stainless screws.

NOTE:

THERE ARE NO PILOT HOES IN THE

BASE OF THE POWER VENT TERMINAL.

1/8” DIAMETER PILOT HOLES SHOULD

BE DRILLED USING THE HOLES IN THE

VERTICAL RAIN CAP AS A GUIDE.

DO NOT SILICONE THE VERTICAL RAIN

CAP TO THE POWER VENT TERMINAL

AS IT NEEDS TO BE REMOVABLE FOR

SERVICING.

15. Attach the vent adaptor directly to the

appliance with three screws. (Fig. #4)

Note: The inner pipe does not need to

be sealed.

16. Connect one of the high temperature

silicone tubes to the upper pressure tap

on the adaptor.(Fig. #4) Secure with the

hose clamp provided and route the tube

through any hole back to control box. This

tube will be connected to the “low” side

of the vacuum switch inside the control

compartment. (Fig. #11) Connect the

second tube to the lower pressure tap

and route to the control box as before.

Connect this tube to the remaining port on

the vacuum switch. Tubes may touch unit

and be trimmed if required. Note: Ensure

that there are no blockages in these

tubes, as this will cause the control to

malfunction.

17. Run the required Simpson Duravent

GS / Secure Vent / Selkirk Direct-temp

pipe from the adaptor to the terminal

assembly. Assemble as per the vent pipe

manufacturer’s instructions including all

shields and restops.

fire-parts.com

110509-12 TCVT.PVB1

Fig. #5

Vertical (Through Roof) Venting

18.000 11.000 11.000 18.000

Part E

Exhaust Shield

- DISCARD -

Part D

Junction Box Cover

Power Vent

TCVT.PVB

Part F

Vertical Rain Cap

TCVT.8074

Part C

Drip Shield

Part B

Vertical Standoff

Part A

Flashing

Site Fabricated Chase

MUST ALIGN

#8 x 1/2" S.S.

(16 Required)

#8 x 1-1/2" S.S.

(8 REQUIRED)

NOTE: Holes to

secure rain cap are

not predrilled

SILICONE ALL

CONNECTING FACES

14-2 Wire w/ Ground

Final Installation Height: 21"

fire-parts.com

110509-12 TCVT.PVB1

The gas control system is located on the right hand side of the

rebox behind an access panel and the decorative panel.

1. Remove burner assembly, burner media and decorative

panels if already installed (see main installation manual for

details).

2. Remove access panel from right hand side of the rebox.

(Fig. #6)

3. Locate and disconnect the spade connectors in the black

wire loop on the right side of the module and in the orange

wire running from the module to the socket labelled “pilot”

on the valve. (Fig. # 6 and 7)

4. Using the jumper wires provided, connect the 120V “hot”

supply wire to one of the black wires from the control module.

Then connect the “hot” wire from the power vent blower to

the other black wire on the control module. (Fig. #9) The

module acts as a switch to turn on the power vent blower.

(Also see wiring diagram on Pg.9)

Fig. #7

Fig. #8

Fig. #9

ACCESS PANEL

SPADE CONNECTORS IN BLACK

WIRE LOOP

ORANGE WIRE FROM

MODULE TO VALVE

Fig. #6

SUPPLIED WIRES TO CONNECT TO

BLACK WIRE ON MODULE

HOT WIRE

FROM BLOWER

HOT WIRE FROM

120V SUPPLY

Control System Connection

fire-parts.com

PRESSURE

SWITCH

LOW SIDE

OF SWITCH

HIGH SIDE

OF SWITCH

110509-12 TCVT.PVB1

5. Connect the pressure switch jumper wires to the orange

wire. (Fig. # 10)

6. Attach a silicone tube from the upper pressure tap on the

power vent adaptor (Fig. #4) to the low port of the pressure

switch. Attach the other silicone tube from the lower pressure

tap to the high port of the pressure switch.

7. Secure the pressure switch in the control box using the

screw provided. (Fig. #12)

8. Continue with installation and reassemble all of the parts

previously removed.

WARNING: This switch must be

installed in a vertical position and

will not function if installed otherwise.

(Fig. 13)

This power vent system can only run on 115 V AC. Before

operating the unit, the battery backup located behind the

wall switch receiver must be removed.

ORANGE WIRE

Fig. #10

Fig. #11

Fig. #12

Fig. #13

fire-parts.com

115 Volt

60 Hz

1.8A

Power Vent Fan

Pressure

Switch

AC Adaptor

Electrical box inside

Control Compartment

Gas

Valve

Module

Wall Switch Receiver

Pull connectors apart

to connect to power vent

White

Green

White

Orange

Black

Red

120 Volt Hot wire (Black)

120 Volt Common wire (White)

1/4” Male

Connector

1/4” Male

Connector

1/4” Male

Connector

1/4” Male

Connector

1/4” Female

Connector

1/4” Female

Connector

1/4” Female

Connector

1/4” Female

Connector

Wiring the Power Vent Kit provided by Town & Country

Communication wires

Main

Pilot

Low pressure side

Orange

Pressure switch

wire (Supplied)

Power Vent switch

wire (Supplied)

Black

STANDARD AWG 14-2 WIRE

OR EQUIVALENT (NOT SUPPLIED)

110509-12 TCVT.PVB1

Wiring Diagram

fire-parts.com

110509-12 TCVT.PVB1

ITEM PART No. DESCRIPTION QTY

1 8024 TUBE, 5/16” OD, 1/16” THICK 2

2 BLOWER POWER VENT 1

*3 5027.15 PRESSURE SWITCH 1

*4 3/8” STRAIN RELIEF 2

5 #8 x 1/2” PAN HD SKT 18.8 STAINLESS STEEL 46

6 ID x .379 OD x .062 THK 2

7 1/4 MED LOCKWASHER 18.8 SS 5

8 STANDARD 18-8 SS, #8 FLAT WASHER 6

9 SP100 .25 x .75 AK 4

10 SCREW, #8-32 x1 1/4 RND HD 4

*11 #8-32 x5/16 PAN QUADREX 1

12 HEX NUT, STAINLESS 18-8 PLAIN 4

13 1/4-20 x1/2 NC GR 5 HEX C/S PLTD 5

14 5096.813 VENTING ADAPTER 1

15 1/4” LDF PAPER 1

*17 BUSHING, SHORTY B625 500 2

18 SIDE COVER, RIGHT 1

19 SIDE COVER, LEFT 1

ITEM PART No. DESCRIPTION QTY

20 INSIDE COVER 1

21 EXHAUST SHIELD 1

22 SECONDARY RAIN SHIELD 2

23 JUNCTION BOX 1

24 TOP COVER 1

25 EXHAUST SCREEN 1

26 FLASHING 1

27 OUTLET AIR CHANNEL 1

28 DRIP SHIELD 1

30 VENT COLLAR 1

31 VENT EXHAUST ASSEMBLY 1

32 VERTICAL RAIN CAP, TCVT 1

33 VERTICAL STANDOFF 1

34 BLOWER WIRING 1

35 TCVT.506271C2 PRESSURE SWITCH WIRING 1

36 TCVT.507156C POWER VENT SWITCH WIRE 1

ITEM 35 AND 36 ARE USED WITH SERIES “C” FIREPLACES ONLY

* NOT SHOWN ONLY ITEMS WITH PART NUMBERS SHOWN ARE SOLD SEPARATELY

Replacement Parts

fire-parts.com

Andere Handbücher für TCWS38

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Town & Country Fireplaces Kamin im Innenbereich Handbücher

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCHF.22BODYA Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.NG03D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces Architectural Series Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54ST SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Gebrauchsanweisung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36ST Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42.NG01 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36D2 ARCH Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54ST SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Gebrauchsanweisung

Town & Country Fireplaces

Town & Country Fireplaces TC36D2 ARCH Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54ST SERIES D Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch