Town & Country Fireplaces TC36AR Bedienungsanleitung

Visit www. townandcountryﬁreplaces.com for the most recent version of this manual

Serial #

TC36D2 & TC36D2 ARCH

USER MANUAL

100817-16 TC36_D & TC36_DAR.ver2 5056.4275D2

MODEL: TC36 & TC36AR

SERIES D - version 2

MODULAR DIRECT VENT

FIREPLACE

WARNING: If the information in these

instructions is not followed exactly, a re or

explosion may result causing property damage,

personal injury or death.

FOR YOUR SAFETY

Installation and service must be performed

by a qualied installer, service agency or

the gas supplier.

WHAT TO DO IF YOU SMELL GAS

• Donottrytolightanyappliance.

• Donottouchanyelectricalswitch.

•Donotuseanyphoneinyourbuilding.

• Immediatelycallyourgassupplierfrom

a neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier

call the re department.

Do notstoreor usegasoline or otherammable

vapours and liquids in the vicinity of this or

any other appliance.

This appliance may be installed in an aftermarket

permanently located,manufactured home (USA only)

or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certied kit is used.

This appliance is suitable for installation in a

bedroom or bed sitting room.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

USER MANUAL

Table of Contents

Your Town & Country replace has been professionally installed by:

Dealer name: _____________________________________________

Phone Number: ___________________________________________

If you discover any problems with your Town & Country replace contact your dealer immediately to have the

unit repaired.

Caution: Do not attempt to repair the replace because you may cause injury to yourself or others, and risk

causing damage to the unit.

Before operating your replace carefully read this manual and pay close attention to all Safety

Warnings. The manual contains important information on the unit’s safe operation and maintenance.

Congratulations on your Town & Country purchase

Caution ........................................................................................ 3

Safety .......................................................................................... 3

Lighting Instructions .................................................................... 4

First Fire ....................................................................................... 5

Special Operator Note ................................................................. 5

Remote Control Operation .......................................................... 5

IFC Module........................................................................... 7

Operating Procedure............................................................ 7

Using the Remote Control Transmitter................................. 8

Temperature indication Display (if thermostat function

is enabled)............................................................................ 8

Turn on the Fireplace............................................................ 8

Turn off the Fireplace............................................................ 8

Manual Bypass of the Remote Fireplace ............................. 8

Remote Flame Control ......................................................... 9

Smart Thermostat (Transmitter Operation) If enabled.......... 9

Instructions for enabling the Thermostat function

for Canadian users. ...................................................................... 9

Room Thermostat (Transmitter Operation) Canada Only. .... 9

Remote dimmer control (Light)........................................... 10

Continuous Pilot/Intermittent Pilot (CPI/IPI) selection........ 10

Key Lock ............................................................................ 10

Low Battery Power Detection ............................................ 10

Linking Remote Handset and Apple®Device to Fireplace ........ 11

Step 1: Procedure for linking / pairing wall switch

to replace ......................................................................... 11

Step 2: Procedure for linking / pairing the wall

switch to remote handset .................................................. 12

Step 3: Optional procedure for linking / pairing a

BlueTooth®enabled apple mobile device to the

replace (iOS only). ............................................................ 12

Using the TC Fire app ........................................................ 13

Maintenance .............................................................................. 14

Glass Panel: ....................................................................... 14

Annual Inspection:.............................................................. 14

Periodically:........................................................................ 14

Warranty .................................................................................... 15

2TC36_D & TC36_DAR.ver2_100817-16

5056.4275D2

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from the

hot viewing glass is provided with the appliance and

shall be installed for the protection of children and

other at-risk individuals.

FOR YOUR SAFETY - Do not install or operate your Town & Country replace

without rst reading and understanding this manual. Any installation or

operational deviation from the following instructions voids the Town & Country

Fireplaces Warranty and may prove hazardous.

This appliance and its individual shut off valve must be disconnected from

gas supply piping system during any pressure testing of that system at test

pressures in excess of 1/2 psig (3.5 kPa).

This appliance must be isolated from the gas supply piping system by closing

its individual manual shut off valve during any pressure testing of the gas

supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).

Note: When lit for the rst time, the appliance will emit a slight odour for a

couple of hours. This is due to the curing of paints, sealants and lubricants

used in the manufacturing process. This condition is temporary. Open doors

and windows to ventilate area. Smoke and fumes caused by the curing

process may cause discomfort to some individuals.

Do not use the replace if any part has been under water. Immediately call a

qualied service technician to inspect the replace and to replace any part of

the control system and any gas control which has been under water.

Due to high temperatures, this gas appliance should be located out of trafc and away from furniture and draperies.

Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns

or clothing ignition.

Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young chil-

dren, and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at-risk

individuals in the house. To restrict access to a replace or stove, install an adjustable safety gate to keep toddlers,

young children, and other at-risk individuals out of the room and away from hot surfaces.

Clothing or other ammable material should not be placed on or near the appliance.

Any grill, panel or door removed for servicing the unit must be replaced prior to operating. Failure to do so may create a

hazardous condition.

Installation and repair should be done by a qualied service person. The appliance should be inspected before use and

at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from

carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of

the appliance be kept clean.

It is our policy that no responsibility is assumed by the Company or by any of its employees or representatives for any

damages caused by an inoperable, inadequate, or unsafe condition which is the result, either directly or indirectly, of any

improper operation or installation procedures.

This appliance must not be connected to a chimney ue serving a separate solid fuel burning appliance.

35056.4275D2

TC36_D & TC36_DAR.ver2_100817-16

We recommend that our gas

hearth products be installed

and serviced by profession-

als who are certied in the

United States by the National

Fireplace Institute® (NFI) as

NFI Gas Specialists

Caution

Safety

FOR YOUR SAFETY READ BEFORE LIGHTING

LIGHTING INSTRUCTIONS

TO TURN OFF GAS APPLIANCE

WARNING:

If you do not follow these instructions exactly, a

fire or explosion may result causing property damage,

personal injury or loss of life.

A.This appliance is equipped with an ignition device which

automatically lights the pilot. Do not try to light the pilot by hand.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be

sure to smell next to the floor because some gas is heavier than

air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

- Do not try to light any appliance.

- Do not touch any electric switch; do not use any phone in your

building.

- Immediately call your gas supplier from a neighbour's phone. Follow

the gas supplier's instructions.

- If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use

tools. If the knob will not push in or turn by hand, don't try to repair it,

call a qualified service technician. Force or attempted repair may

result in a fire or explosion.

D.Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the

appliance & to replace any part of the control system & any gas

control which has been under water.

1. STOP! Read the safety information above on this label.

2. This appliance is equipped with an ignition device which

automatically lights the pilot. Do not try to light the pilot by hand.

3. Push the "On/ Off" switch to turn the fireplace ON.

- If the burner does light go to step 6.

- If the burner does not light, complete steps 4 through 5.

- If the burner will not light or stay lit after several tries, push the

"On/ Off" switch for the fireplace to OFF, turn off all electric power

to the fireplace and call your service technician or gas supplier.

Note: Sufficient time must be allowed for air to escape from lines if

the unit is being lit for the first time.

4. Push the "On/ Off" switch to the fireplace Off.

5. Allow sufficient length of time (minimum 5 minutes) for any gas in the

combustion chamber to escape. If you still smell gas, STOP! Follow

"B" in the safety information above on this label. If you don't smell

gas, go to step 3.

6. Set fireplace to desired setting by using hand held remote.

Push the "on/ off" switch to the "Off" position.

2. Turn off all electric power to the appliance and remove backup

batteries if service is to be performed or for extended shutdown.

Due to high surface temperatures, keep children, clothing and furniture away. Keep burner and control compartment clean. See installation and

operating instructions accompanying the appliance.

A cause de la temperature elevee des parios, tenir eloignes les enfants, les vetements et les meubles. Maintenir propres le bruleur et le

compartiment de commande. Voir les instructions relatives a l'installation et au fonctionnement qui accompagnent l'appareil.

CAUTION:

Hot while in operation. Do not touch. Severe burns may result. Keep children,

clothing, furniture, gasoline and other liquids having flammable vapours away. Keep burner and control

compartment clean. See installation and operating instructions accompanying the appliance.

ATTENTION:L'appareil est chaud lorsqu'il fonctionne. Ne pas toucher l'appareil. Risque de

brûlures graves. Serveiller les enfants. Garder les vêtements, le meubles, l'essence ou autres liquides

produisant des vapeurs infl ammables loin de l'appareil. S'assurer que le brûleur et le compartiment des

commandes sont propres. Voir les instructions d'installation et d'utilisation qui accompagnent l'appareil.

090713

5051.185

GBWY

4TC36_D & TC36_DAR.ver2_100817-16

5056.4275D2

Lighting Instructions

When lit for the rst time, the replace will emit a slight odor for a couple of hours. This is due to the curing of paints,

sealants and lubricants used in the manufacturing process. This condition is temporary. Open doors and windows to

ventilate area. Odors caused by the curing process may cause discomfort to some individuals.

It is normal for replaces fabricated of steel to give off some expansion and/or contraction noises during the start up or

cool down cycle. Similar noises are found with your furnace heat exchanger or cook stove oven.

Blue back lit LCD display

ON/OFF Key

THERMOSTAT Key

UP/DOWN Arrow Key

MODE Key

NOTE: Pilot may take

up to 30 seconds to ignite

each time the “ON” button

has been selected.

Figure 1: Proame 2 handset.

55056.4275D2

TC36_D & TC36_DAR.ver2_100817-16

First Fire

Special Operator Note

Remote Control Operation

Attention!

• Turn off the main gas supply for the appliance during instal-

lation or maintenance of the receiver/module device.

• Turn off main gas supply for the appliance prior to removing

or reinserting the batteries.

• In case of remote control malfunction, turn off the replace

using the “on/off” main switch located on the wall.

• For installation/maintenance, turn off the replace at the on/

off switch located on the wall and at the replace power

supply circuit breaker.

NOTICE: The thermostat function is disabled by default. Thermostat function is not

permissible in the USA but is permissible in Canada. Instructions for enabling the thermostat

function in Canada, see “Instructions for enabling the Thermostat function for Canadian

users.” on page 9

OFF

SMART

MAX MAX

KEY LOCK

LOW BATTERY ALARM

ROOM

TEMPERATURE

CPI MODE

DIMMER ONFLAME LEVEL

OFF / ON

SET POINT:

TEMPERATURE/LEVEL/STATE

THERMOSTAT OFF/

ON/SMART

TRANSMISSION

* SEE NOTICE REGARDING

THERMOSTAT USE

Figure 2: Proame 2 LCD screen details.

6TC36_D & TC36_DAR.ver2_100817-16

5056.4275D2

Fireplace Description

The Proﬂame 2 Remote Control Fireplace consists of three elements:

1. Proame 2 Remote Control Transmitter.

2. Proame Integrated Fireplace Control (IFC) board and a wiring harness to connect the IFC to the gas valve

and stepper motor.

3. Wall mounted Remote Control Receiver - page 8.

Transmitter (Remote Control with LCD Display)

The Proame 2 Transmitter uses a streamline design with a simple key layout and an informative LCD display

(Figure 1). The remote control transmitter is powered by 3 AAA batteries. A mode key is provided to index

between the features and a thermostat key is used to turn on/off or index through thermostat functions

(Figure 2).

IFC Module

The Proame 2 Integrated Fireplace Control (IFC) module is a device that allows automatic ignition and pilot

ame supervision and commands the functions of the replace. It’s congured to control the ON/OFF main

burner operation, giving the choice of both IPI (intermittent pilot ignition), and CPI (continuous pilot ignition)

modes. The Proame 2 IFC module controls and connects directly to the pilot assembly and the automatic

valve using low electric power.

The IFC module can be powered by both an AC power supply, and battery pack for back up. The Proame 2

offers the added ability to control the comfort fan speed from OFF through six (6) speeds, and remotely actu-

ated dimmable lights. The external batteries can provide DC power to the IFC allowing the batteries to be

used only when line power is interrupted or lost, and if the replace does not use a power vent.

Operating Procedure

The replace must rst be linked to the wall switch. Then the wall switch must be linked to the remote hand-

set. Instructions for both of these procedures including instructions for enabling a BlueTooth®enabled apple

mobile device to the replace, See “Linking Remote Handset and Apple® Device to Fireplace” on page 11.

75056.4275D2

TC36_D & TC36_DAR.ver2_100817-16

Program button

Using the Remote Control Transmitter

Temperature indication Display (if thermostat function is enabled)

With the remote control transmitter in the “OFF” position, press the ther-

mostat and mode keys at the same time. Look at the LCD screen on the

remote control transmitter to verify that a C or F is visible to the right of the

room temperature display (Figure 7 or Figure 8).

Turn on the Fireplace

With the replace OFF, press the ON/OFF key on the remote control trans-

mitter. The remote control transmitter display will show the active icons on

the screen. At the same time the wall switch will activate the replace via

the IFC module. A single “beep” from the IFC module will conrm reception

of the command.

Turn off the Fireplace

With the replace ON, press the ON/OFF key on the remote control trans-

mitter. The remote control transmitter LCD display will only show the room

temperature (Figure 7 or Figure 8). At the same time the IFC module will turn

off the replace. A single “beep” from the IFC module conrms reception of

the command.

Manual Bypass of the Remote Fireplace

If the batteries of the remote control transmitter are low or depleted, the

replace can be turned on and off manually using ON/OFF switch located on

Town & Country wall switch. This will bypass the remote control transmitter.

Figure 3: Wall switch

interface side.

Figure 4: Wall switch

battery side.

Figure 5: Town & Country

wall switch.

Figure 6: Proame 2 remote

battery bay.

Figure 7: Display in

fahrenheit.

Figure 8: Display in

celcius.

8TC36_D & TC36_DAR.ver2_100817-16

5056.4275D2

Remote Flame Control

The Proame 2 has six (6) ame levels. With the replace turned on, and

the ame level at maximum height, press the down arrow key on the

remote once to reduce the ame height by one step until the ame is

turned off (Figure 9).

The up arrow key will increase the ame height each time it is pressed. If

the up arrow key is pressed while the replace is on but the ame is off,

the ame will come on in the high position. A single “beep” will conrm

reception of the command.

Flame Off

Flame level 5

Flame level Max

Flame level 1

Figure 9: Flame level control.

Figure 10: Room temperature

control.

Figure 11: Smart ame

function.

Figure 12: Smart ame

function set low.

Smart Thermostat (Transmitter Operation) If enabled.

The Smart Thermostat function adjusts the ame height in accordance to the difference between the set point

and the room temperatures. As the room temperature gets closer to the set point, the Smart Function will

modulate the ame down. If the room temperature is cool, the Smart Function will modulate the ame up.

To activate this function, press the THERMOSTAT button (Figure 1) until the word “SMART” appears to the

right of the temperature icon (Figure 11). To adjust the set point, press the up or down arrow buttons until the

desired set point temperature is displayed on the LCD screen of the remote control transmitter (Figure 11 and

Figure 12).

The thermostat key (Figure 1) on the remote handset needs to be held down. Keep it pressed down and

remove one of the three batteries from the remote handset. Simply re-install the battery that was removed

and the feature is activated. Use the same procedure to disable the thermostat function.

Instructions for enabling the Thermostat function for Canadian users.

Room Thermostat (Transmitter Operation) Canada Only.

The remote control transmitter can operate as a room thermostat. The thermostat can be set to a desired

temperature to control the comfort level in a room. To activate this function, press the thermostat key

(Figure 1). The LCD display on the remote control transmitter will change to show that the room thermostat

is “ON” and the set temperature is now displayed (Figure 10). To adjust the set point, press the up or down

arrow keys until the desired set point temperature is displayed on the LCD screen of the remote control

transmitter.

95056.4275D2

TC36_D & TC36_DAR.ver2_100817-16

Low Battery Power Detection

Transmitter

The life span of the remote control batteries depends on various factors: quality of

the batteries used, the number of ignitions of the Heater, the number of changes to

the room thermostat set point, etc.

When the remote batteries are low, an icon will appear on the LCD display of the

remote (Figure 16) before all battery power is lost. When the batteries are replaced

this icon will disappear.

Receiver

The life span of the IFC module batteries depends on various factors: quality of the batteries used,

the number of ignitions of the Heater, the number of changes to the room thermostat set point, etc.

When the IFC batteries are low, a “double-beep” will be emitted from the IFC module when it receives

a command from the remote. This is an alert for a low battery condition for the IFC board. When the

batteries are replaced, a single “beep” will be emitted from the IFC module when a key is pressed.

Key Lock

This function will lock the keys to avoid unsupervised operation. To activate this func-

tion, press the MODE and UP keys at the same time (Figure 1). The lock icon will

appear (Figure 15). To de-activate this function, press the MODE and UP key at the

same time.

Remote dimmer control (Light)

To activate this function use the Mode Key (Figure 1) to index

to the light bulb icon (Figure 13). The intensity of the output

can be adjusted through six (6) levels. Use the Up/Down

Arrow Keys to adjust the output level. A single “beep” will

conrm reception of the command.

Continuous Pilot/Intermittent Pilot (CPI/IPI) selection

With the system in the “OFF” position, press the Mode Key

(Figure 1) to index to the CPI mode icon (Figure 14). Pressing

the Up Arrow Key will activate the Continuous Pilot Ignition

mode (CPI). Pressing the Down Arrow Key will return to IPI. A

single “beep” will conrm the reception of the command.

Figure 13: Dimmer light control.

Figure 14: IPI - CPI control.

Figure 15: Key lock.

Figure 16: Low battery

icon.

10 TC36_D & TC36_DAR.ver2_100817-16

5056.4275D2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Town & Country Fireplaces Kamin im Innenbereich Handbücher

Town & Country Fireplaces

Town & Country Fireplaces Series C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces Model TC42SeriesC Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42.NG04C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54CE2 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54ST SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 SEE-THRUC SERIES Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30D2 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54ST SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36ST.NGST04D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54STOK Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 TC36ST.NGST03D Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch