Town & Country Fireplaces Model TC42SeriesC Bedienungsanleitung

1 TC42.CE 080906-10

For reference only. Consult Manual before installation

for

architects

designers

and

builders

Fireplace and Venting Specications

Model TC42 Series C

IMPORTANT

This booklet is intended as a basic

specication guide for architects,

designers and builders. Please

refer to the Instruction Manual

supplied with the replace for

detailed information regarding

installation and operation.

Product installation manuals can

also be viewed at:

www.townandcountryreplaces.net.

TC42

Series C

2 TC42.CE 080906-10

For reference only. Consult Manual before installation

Fireplace Dimensions

Examples of Common Locations

TC42.CE Architect.dxf

Available on CD ROM and

www.townandcountryreplaces.net

3 TC42.CE 080906-10

For reference only. Consult Manual before installation

Mantel Clearance Chart

Minimum Clearances to Combustibles

CEILING

ADJACENT

WALL OR

MANTEL

SUPPORT

MANTEL

UNIT MAY BE RECESSED UP TO

6" WITH NON-COMBUSTIBLE

MASONRY TYPE MATERIAL

TOP OF LINTEL BAR

24”

38 1/8”

4”

COMBUSTIBLE FRAMING

AND FINISH WALL ABOVE

STANDOFFS

MAY USE COMBUSTIBLE

FACING MATERIAL IN THIS

AREA

NON-COMBUSTIBLE

FINISH MATERIAL

STANDOFFS

STEEL FRAMING

FIREPLACE FRONT

A 9" D 12"

B 6" E 6 3/4"

C 3" F 1 1/2"

REF. MANTLE CLEARANCE REF. MANTLE EXTENSION

NON-COMBUSTIBLE ZONE.

DO NOT INSTALL ANY

COMBUSTIBLE MATERIAL,

ELECTRICAL WIRING,

INSULATION, PLASTIC

VAPOUR BARRIER OR

GAS PLUMBING IN THIS

AREA

Side standoffs...................... 0 in. (0 mm)

Back standoffs..................... 0 in. (0 mm)

Top standoffs ....................... 0 in. (0 mm)

Bottom of appliance............. 0 in. (0 mm)

Adjacent sidewall................. 4 in. (102 mm)

Ceiling to appliance ........... 24 in. (610 mm)

Mantel to appliance.........................See above

Maximum mantel extension ..........See above

Horizontal vent pipe

Top............................ 1-3/4 in. (45 mm)

Sides ........................ 1-3/4 in. (45 mm)

Bottom ...................... 1-3/4 in. (45 mm)

4 TC42.CE 080906-10

For reference only. Consult Manual before installation

26 1/8"

54"

12 5/8"

3/4"

54"

Minimum Combustible Framing Dimensions

Steel Stud Framing Kit Dimensions

Kit supplied with unit

Concrete

Board Detail

Concrete board (or other

non-combustible material)

must extend 12" above and

5" to the sides of the framing

edges.

CONCRETE

BOARD

All other framing

can be done with

conventional lumber

Including Sheetrock

Non-combustible Zone.

Do not install any

combustible material,

electric wiring,

insulation, plastic

vapour barrier or

gas plumbing

within the steel

stud frame.

61 3/4"

21 5/16"

61 3/4"

30 1/8"

3/4"

54"

87 5/16"

54"

NOTE: Fireplace should be in its

nal location before framing.

5 TC42.CE 080906-10

For reference only. Consult Manual before installation

Town & Country Fireplaces feature the Maestro Control

System*. Each replace arrives equipped with a small

wall-mounted decor-series faceplate that is located by

wire up to 25’ from the hearth. This permits on/off oper-

ation, ame modulation and houses the battery back-up

system for operation during power outages.

The concealed valve system within the replace fea-

tures a quick disconnect modular design, and external

ports for gas set-up and testing. With no batteries in the

replace, there is little need for the property owner to

open the glass upon installation.

An elegant handheld 4-way programmable remote is

also included with every unit. A count-down timer, week-

day/weekend programmable on/off, manual control and

thermostat mode (where permitted), are programmed

on the easy-to-read LCD display. The remote also offers

a child lock-out feature.

Each Town & Country Fireplace is shipped with a

Maestro Control electronic ignition system. Conversion

to standing pilot is possible at the press of a button.

*Available on Series C Town & Country replaces only.

Maestro Control System

Up to 25 Feet

Through the Wall Installation

Hearth Extension

While a hearth extension is not required for this

replace, one is recommended for aesthetic

reasons. The hearth extension should be non-

combustible and must not be any more than

1" above the bottom of the replace. If thicker,

replace must be raised up accordingly.

Caution: Hearth extensions

thicker than 1" will interfere with

the window frame.

WINDOW

FRAME

HEARTH

EXTENSION

WINDOW

TRACK

SUB-FLOOR

HORIZONTAL

TERMINAL

14 1/2" FRAMED

OPENING

* Minimum height from the oor to center of the opening with a

maximum horizontal run of 18" usingTC vent.The height will need

to be increased with a longer horizontal run.

WALL SHIELD

THIMBLE

ELBOW

24” VENT

PIPE

12” VENT PIPE

*74 1/4"

6 TC42.CE 080906-10

For reference only. Consult Manual before installation

Wall Termination Venting Charts

24” Pipe

Length

Min.

NOTE: The vent must not exceed a total length of 68 feet.

Any combination of rise and run may be used but must

be constrained to the boundaries of this chart. A total of

3 90˚ elbows or combination of other elbows equalling

90˚ can be used without reducing horizontal run. For each

additional 90˚ elbow, or an equal combination of elbows,

reduce horizontal vent run by 2 feet. Ensure vent pipe is

properly supported.

74 1/4

*Minimum Vent Pipe Centerline Height

Minimum rise

Pipe length

Maximum run

Pipe length

Maximum

74 1/4” 1-24” 18" 1-12"

78 1/2” 1-12" 1-18" 75 3/4" 1-48" 1-12"

84 1/2” 1-24" 1-12" 11' 2" 2-48" 1-24"

90 1/2” 1-24" 1-18" 15' 10 1/2" 3-48" 1-24"

1-12 "

98 1/4” 1-48” 20’ 10 1/2” 5-48"

** All dimensions are approximate. Both rise and run may vary with different combinations of pipe.

TCVT Wall Vent.dxf

Available on CD ROM

and www.

townandcountryreplaces.net

7 TC42.CE 080906-10

For reference only. Consult Manual before installation

Roof Termination Venting Charts

24” Pipe

Length Min. NOTE: The vent must not exceed a total length of 68 feet.

Any combination of rise and run may be used but must

be constrained to the boundaries of this chart. A total of

4 90˚ elbows or combination of other elbows equalling

90˚ can be used without reducing horizontal run. For each

additional 90˚ elbow, or an equal combination of elbows,

reduce horizontal vent run by 2 feet. Ensure vent pipe is

properly supported.

** All dimensions are approximate. Both rise and run may vary with different combinations of pipe.

TCVT Roof Vent.dxf

Available on CD ROM

and www.

townandcountryreplaces.net

Minimum rise

Pipe length

Maximum run

Pipe length

Maximum

74 1/4” 1-24” 29" 1-12"

78 1/2” 1-12" 1-18" 77 1/4" 1-48" 1-12"

84 1/2” 1-24" 1-12" 11' 1 1/2" 2-48" 1-24"

90 1/2” 1-24" 1-18" 15' 10" 3-48" 1-24"

1-12 "

98 1/4” 1-48” 20' 10” 5-48"

8 TC42.CE 080906-10

VVV

Minimum clearances to the vent terminal must be maintained as shown below. Measure clearances to the nearest edge

of termination hood.

NOTE: Vent terminal must not be recessed into a wall or siding.

A= clearances above grade, veranda, porch, deck, or balcony [* 12

inches (30 cm) minimum]

B= clearance to window or door that may be opened [* 12 inches

(30 cm) minimum]

C= clearance to permanently closed window [minimum 12 inches

(30 cm) recommended to prevent condensation on window]

D= vertical clearance to ventilated soffit located above the terminal

within a horizontal distance of 2 feet (60 cm) from the edge of

the terminal [30 inches (76 cm) minimum]

E= clearance to unventilated soffit [30 inches (76 cm) minimum]

F= clearance to outside corner [6 inches (15 cm) minimum]

G= clearance to inside corner [6 inches (15 cm) minimum]

H= * not to be installed above a meter/regulator assembly within 3

feet (90 cm) horizontally from the center-line of the regulator

I= clearance to service regulator vent outlet [* 6 feet (1.8 m)

minimum]

J= clearance to nonmechanical air supply inlet to building or the

combustion air inlet to any other appliance [* 12 inches (30

cm) minimum]

K= clearance to a mechanical air supply inlet [* 6 feet (1.8 m)

minimum]

L= ^ clearance above paved side-walk or a paved driveway

located on public property [* 7 feet (2.1 m) minimum]

M= clearance under veranda, porch, deck, or balcony [30 inches

(76 cm) minimum**]

^ a vent shall not terminate directly above a side-walk or paved driveway which is located between two single family dwellings and

serves both dwellings*

** only permitted if veranda, porch, deck, or balcony is fully open on a minimum of 2 sides beneath the oor*

* as specied in CGA B149 Installation Codes, Note: local Codes or Regulation may require different clearances

* for U.S.A. Installations follow the current National Fuel Gas Code, ANSI Z223.1

AIR SUPPLY INLET

VENT TERMINAL GAS METER

AREA WHERE TERMINAL

IS NOT PERMITTED

Vent Terminal Minimum Clearances

For reference only. Consult Manual before installation

9 TC42.CE 080906-10

For reference only. Consult Manual before installation

Power Vent

Remote Heat Kit

Stainless Steel Vent Terminal

TCVT.SSWTA.dxf

Available on CD ROM

and www.

townandcountryreplaces.net

TCVT.PVB-Architect.dxf

Available on CD ROM

and www.townandcountryreplaces.net

TC.RHKA-Architect.dxf

Available on CD ROM

and www.townandcountryreplaces.net

Transfer heat to a room adjacent

to, above or below the replace.

Up to two optional Remote Heat

Kits can be installed on each

Town & Country Fireplace.

Reach almost any room or commercial setting. Optional Power Venting allows runs up

to 66’ from an outside wall or roof surface. Vent horizontally or vertically with up to six

90-degree elbows, including runs up to 3’ below the replace.

The premium Power Vent fan runs quietly outside, at the exterior terminal.

The T&C Stainless Steel Vent Terminal is intended

for use in climates that warrant stainless steel con-

struction as well as in hard to reach places.The two-

phase installation allows the sleeve to be installed

during the construction phase, while the terminal

can be installed from the inside of the structure at

the same time as the replace.

The terminal kit is suitable for both residential and

commercial installation.

For reference only. Consult Manual before installation

Web: www.townandcountryreplaces.net

Phone: 1-877-715-2664

2975 Allenby Road, Duncan, BC Canada V9L 6V8

Printed in Canada

Inhaltsverzeichnis

Andere Town & Country Fireplaces Kamin im Innenbereich Handbücher

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Gebrauchsanweisung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCHF.22BODYA Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCVT.WSPVB1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54OD Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.NGST04C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.38CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces HELIFIRE 360 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54ST SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.RHKA Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces Architectural Series Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36ST Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch