Town & Country Fireplaces TC36.NGST04C Bedienungsanleitung

IMPORTANT:

THESE INSTRUCTIONS ARE TO REMAIN

WITH THE HOMEOWNER

These instructions are supplementary to the Installation

and Operating Instructions supplied with the replace

and should be kept together. Refer to the Installation

and Operating Instructions for proper gas supply, safety

requirements and operating instructions.

101812-16 TC36.NGST04C 5056.42801C4

TC36 See-Thru

TRANQUILITY

BURNER KIT

INSTRUCTIONS

PART#TC36.NGST04C

FOR TC36 SEE-THRU

SERIES C

Package Contents

Tranquility Burner Installation

TC36.NGST04C 101812-16

5 lbs. Sand 5096.9935

1 Bag tapered plugs TC36.503152

1 Burner assembly TC36.9410

2 Line covers TC36.9699PBKA

1 Pebble assembly TC42.9499

1 Instruction pack 5056.42801.C4

In these instructions the right and left sides of the

replace are referenced during the installation

process. The right side has the control access

cover in it.

1) Place base panels onto unit oor.

2) Attach a line cover to the left side of rebox

using screw from top center of air channel.

(Fig #1)

3) Remove panel retainer clips from the top heat

shield. Install left porcelain panel. (Fig #2)

Fig #1

Fig #2

TC36.NGST04C 101812-16

Tranquility Burner Installation

If converting to propane see

conversion instructions on page #6

before proceeding.

Set shutter according to fuel used. Fully open

for propane, closed for natural gas.

4) Place burner assembly into center of porcelain

base panels. (Fig #3)

5) Attach fuel ex lines to bulkhead ttings.

(Fig #4)

CAUTION: Ensure that all

connections are gas tight.

Fig #3

Fig #4

RED END TO

RED DOT

WHITE END TO

WHITE DOT

MODULE

BULKHEAD PLATE

2 SCREWS

TC36.NGST04C 101812-16

6) Secure the electrical bulkhead plate and

gasket to the rebox. (2 screws) Attach the

ignition and sensor wires to the module. Red

end to the connector marked by the red dot,

white end to the connector marked by the

white dot(Fig. #5 & 6)

Fig #5

Fig #6

TC36.NGST04C 101812-16

Fig #7

Fig #8

7) Place second line cover over lines and

attach to right side of rebox using top

bulkhead screw. (Fig #7)

8) Install right porcelain panel and re-install panel

retainer clips. (Fig #8)

TC36.NGST04C 101812-16

Fig #10

Fig #9

9) Insert tapered plugs into raised burner ports to

prevent sand from entering ports. (Fig #9)

10) Place sand in tray. Brush sand smooth and

level to just below top of raised burner ports.

Gently remove excess sand from around ports.

(Fig #10 & 11)

Fig #11

TC36.NGST04C 101812-16

Fig #12

Fig #13

11) Remove tapered plugs from ports. (Fig #12)

12) Gently place pebble assembly onto sand base

using pins to locate position. (Fig #13)

NOTE: Do not lift pebble assembly by the

top rocks.

13) The three loose rocks may be placed

anywhere in the sand around the pebble

assembly (Fig #14)

NOTE: Do not place on top of the main

pebble assembly as sooting and poor

performance could occur.

14) Install the door. Unit is ready for lighting.

TC36.NGST04C 101812-16

Fig #14

WARNING

This conversion kit

shall be installed by a

qualied service agency

in accordance with the

manufacturer's instructions

and all applicable codes

and requirements of

the authority having

jurisdiction.

If the information in these

instructions is not followed

exactly, a re, explosion

or production of carbon

monoxide may result

causing property damage,

personal injury or loss of

life.

The qualied service

agency is responsible for

the proper installation of

this kit.

The installation is not

proper and complete

until the operation of the

converted appliance is

checked as specied in the

manufacturer's instructions

supplied with the kit.

If the unit is to be used on propane

convert as follows using the

components supplied with this

burner:

CAUTION

The gas supply and electrical power

shall be shut off before proceeding

with the conversion.

Note: Factory supplied components must be

used to ensure correct input.

After conversion conrm proper manifold

pressure.

1. Remove the 2 front screws holding the

burner tray in place.

(Fig. #16)

2. Gently lift up the burner tray while

sliding to the left to disengage the

burner tube from the orice. Then tip

back to expose the orice.

3. Using a 1/2” wrench, undo the

natural gas burner orice,

(marked #25). Apply a small amount

of pipe joint compound to the threads

of the propane burner orice

(marked 3/32) to ensure a good seal,

before screwing it into the tting.

Loosen the primary air shutter screw,

open shutter fully and re-tighten.

(Fig. #17)

4. Remove the 2 screws

holding the pilot assembly in place with

a stubby screwdriver.

(Fig #18)

The burner assembly must

be removed from the unit if

previously installed.

Propane Conversion

Fig #16

Fig #17

Fig #18

LP GAS/

DU GAZ LP

12.5 in/wc /12.5 po/c.e.

(3.11 kPa)

13.9 in/wc / 13.9 po/c.e.

(3.45 kPa)

11.0 in/wc / 11.0 po/c.e.

(.95 kPa)

3/32” (2.38 mm)

Max.: 61,000 (17.9)

Min.: 46,200 (13.5)

260911 6-TC42C 5052.5206C

Date: ______________________

By / Par: ___________________

Kit # TC42.LPKTB/EB/EC for use with model:

Pour utilise avec du modèle:

This appliance was converted

to PROPANE GAS with this

kit on this date by the or-

ganization which accepts the

responsibility that this conver-

sion has been properly made.

/ Cet appariel etair converter

au gaz LP par l’emploi de la

trousse de conversion par une

organization qui accepte la

responsibilité pour une instal-

lation en bon état.

TC36.NGST03,04

TC42 Series C

MAIN BURNER

(3/32”) ORIFICE (5021.31)

MINIMUM RATE SCREW (5005.016)

CONVERSION LABEL (5052.52083)

TC36.NGST04C 101812-16

Fig #15

TC36.NGST04C 101812-16

HOLE

5. With a 7/16”wrench loosen the pilot head

on the pilot assembly using a wrench to

hold the bracket steady. (Fig. #19)

6. Slide the pilot adjustment band over and

ensure that the hole in the orice band

is showing.

Fig. #20a shows NG position

Fig. #20b shows LP position).

Re-attach the pilot assembly.

7. Remove the access panel, 10 screws,

and set aside.

8. Remove the minimum rate screw

located in the valve. (Fig. #21)

The minimum rate screw is sealed with

an o-ring. Use a thin bladed

screwdriver to back the screw out past

the limit of the threading. At this point

a groove on the screw body will be

visible just above the valve body. Insert

a thin tool (knife blade or ne

screwdriver blade) into the groove and

gently pry the screw up.

9. Replace the minimum rate screw with

the one provided in the propane con-

version kit supplied with this replace.

Ensure that the screw is fully seated.

(Fig. #22)

Fig #19

Fig #20a

Fig #21

Fig #22

NG POSITION LP POSITION

Fig #20b

Inhaltsverzeichnis

Andere Town & Country Fireplaces Kamin im Innenbereich Handbücher

Town & Country Fireplaces

Town & Country Fireplaces TC30.CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.RHKA Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54DST Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Gebrauchsanweisung

Town & Country Fireplaces

Town & Country Fireplaces HELIFIRE 360 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCVT.WSPVB1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 SEE-THRUC SERIES Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36ST.NGST04D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36.NGST03 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC42 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS38 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30.NG02CN Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.38CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.38CE3 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch