Tripp Lite B130-202 Bedienungsanleitung

Owner’s Manual

VGA Over Cat5 Extender Kits

with EDID Copy –

2 Local, 2 Remote

Models: B130-202 and B130-202A

1111 W. 35th Street, Chicago, IL 60609 • www.tripplite.com/support

Product Features 2

Package Includes 2

Optional Accessories 3

EDID Copy 4

Installation Instructions 6

Troubleshooting 8

Warranty & Product Registration 11

14-11-117-93-333B.indd 1 11/24/2014 2:51:41 PM

Product Features

Package Includes

• Connect up to four monitors; 2 local and 2 remote

• Extends a 1440 x 900 @ 60Hz signal up to 165 ft. (50 m)

from the source

• Extends a 1024 x 768 @ 60Hz signal up to 500 ft. (150 m)

from the source

• B130-202A transmits both VGA video and mono audio

• EDID copy feature ensures optimal display compatibility

• Built-in Equalization control allows for adjustment of the video image

• All operating systems supported

• Plug and play, no software or drivers required

• HDCP compliant

• B130-202 or B130-202A Transmitter Unit

• B130-202 or B130-202A Receiver Unit

• (x2) External Power Supplies (Input: 100-240V, 50/60Hz, 0.5A

Output: 5V, 2A)

• Screwdriver for Equalization adjustment

• Owner’s Manual

14-11-117-93-333B.indd 2 11/24/2014 2:51:41 PM

Optional Accessories

• N022-01K-GY Gray Cat5e Bulk Cable, 24AWG, Solid Wire – 1,000 ft.

• N202-Series Cat6 Snagless Patch Cable, 24AWG, Solid Wire

• N222-01K-GY Gray Cat6 Bulk Cable, 24AWG, Solid Wire – 1,000 ft.

• P312-Series 3.5 mm Audio Cables

• P502-Series High Resolution VGA Monitor Cables with RGB Coax

• P504-Series High Resolution VGA Video + 3.5 mm Audio Cables with

RGB Coax

• P524-01K Zero-Skew UTP Bulk Cable – 1,000 ft.

14-11-117-93-333B.indd 3 11/24/2014 2:51:41 PM

EDID Copy

Compatibility issues can occur when EDID information is not properly

communicated between the source and the display. The B130-202

and B130-202A include an EDID copy feature which stores a monitor’s

EDID information in the transmitter and sends it to the source, ensuring

optimal compatibility.

The transmitter can only store EDID information copied from a single

monitor. You should copy the EDID information of the monitor that

has the lowest maximum supported resolution of all monitors being

connected. This monitor must also support video resolutions that are

supported by the other monitors.

For example, if you plan to use three monitors that support the

resolutions listed below, you should copy the EDID information from

Monitor A because the highest resolution it supports is 1600 x 1200,

which is lower than the highest supported resolutions of the other two

monitors. Also, Monitor A’s supported resolutions are also supported by

Monitors B and C.

A. 1600 x 1200, 1024 x 768, 800 x 600

B. 1920 x 1080, 1680 x 1050, 1600 x 1200, 1024 x 768, 800 x 600

C. 1920 x 1080, 1680 x 1050, 1600 x 1200, 1280 x 768, 1152 x

768, 1024 x 768, 800 x 600

If you are not using the EDID copy feature, the transmitter will use a

default set of EDID information.

To use the EDID copy feature, follow the instructions below:

1. Determine the monitor to perform the EDID copy feature on per the

example in the EDID Copy section above.

2. Connect the powered-on monitor to the input port of the transmitter

unit.

3. Connect the external power supply to the transmitter unit and plug

it into a Tripp Lite Surge Protector, Power Distribution Unit (PDU) or

Uninterruptible Power Supply (UPS).

14-11-117-93-333B.indd 4 11/24/2014 2:51:41 PM

EDID Copy

4. The Red Power LED will illuminate to indicate that the transmitter

is receiving power. The Orange EDID LED will initially be off. When it

illuminates, the EDID information from the connected monitor has

been copied.

Note: The Orange EDID LED blinks when an EDID scan is taking place, and

stops blinking and illuminates when the scan is complete. When a monitor is

connected, its EDID information will be copied and stored on the transmitter

unit. If no monitor is connected, the scan will still take place and the

orange LED will blink/illuminate, but no EDID information will be copied. The

information stored on the transmitter will remain unchanged.

5. Once you have completed your installation (see the following section

for installation instructions), you can verify that the EDID information

was copied via the Display Settings screen on your computer. If

the model name of the monitor that you copied is shown in the

Display ﬁeld of the screen, the EDID information has been copied

successfully.

14-11-117-93-333B.indd 5 11/24/2014 2:51:42 PM

Installation Instructions

Notes:

• If using the EDID copy feature, perform the procedure from the EDID Copy

section of this manual prior to installation. If you are not using the EDID copy

feature, the transmitter will use a default set of EDID information.

• The diagram above shows a B130-202 installation. The B130-202A installation

will be the same, except for the addition of audio connections.

• Test to make sure that the entire installation works properly prior to pulling cables

through ceilings/walls.

• To achieve maximum distance and performance, 24AWG solid wire Cat5e/6 cable

must be used. The use of stranded wire Cat5e/6 cable, or cable with a gauge

(AWG) size higher than 24AWG, will result in shorter extension distance.

All Tripp Lite N202-Series Cat6 cables are made with 24AWG solid wire.

Tripp Lite’s N022-01K-GY (Cat5e) and N222-01K-GY (Cat6) are 24AWG solid

wire bulk cables. For optimal image quality, use Zero-Skew cable, such as

Tripp Lite’s P524-01K.

• To achieve maximum resolution, it is recommended that you use Tripp Lite

P502-Series VGA video or P504-Series VGA video and audio* cables with

RGB coax.

UP TO 500 ft. (150 m)

Remote Unit

(Receiver)

Local Unit

(Transmitter)

Source

3 6

14-11-117-93-333B.indd 6 11/24/2014 2:51:42 PM

Installation Instructions

1Make sure that the power to the source and other equipment being

connected is turned off.

2Connect the VGA and audio* source to the INPUT port(s) on the

transmitter unit using a VGA and audio* cable.

3(Optional) – Connect a local monitor and speakers* to the OUTPUT 1

and OUTPUT 2 ports on the transmitter unit using VGA and audio*

cables.

4Connect the external power supply to the transmitter unit, and then

plug it into a Tripp Lite Surge Protector, Power Distribution Unit (PDU)

or Uninterruptible Power Supply (UPS).

5Using Cat5e/6 cable, connect the RJ45 OUTPUT port on the

transmitter unit to the RJ45 INPUT port on the receiver unit.

6Connect a monitor and speakers* to the OUTPUT 1 and OUTPUT 2

ports on the receiver unit using VGA and audio* cables.

7Connect the external power supply to the receiver unit, and then plug

it into a Tripp Lite Surge Protector, PDU or UPS.

8Turn on the power to the source and connected equipment.

9If necessary, adjust the Equalization setting using the included

screwdriver to improve the video image.

* If using the B130-202A

14-11-117-93-333B.indd 7 11/24/2014 2:51:42 PM

Troubleshooting

If you are unable to get an acceptable image after following the

installation instructions, try the troubleshooting tips below.

1Are the external power supplies that came with the product connected

and plugged into a working power source? For the product to function

properly, it must be connected to and receiving power from the

external power supply.

2Was the power to the VGA source turned off prior to installation? If

not, restart your computer.

3Compatibility issues can occur when EDID information is not

properly communicated between the source and the display. The

B130-202 and B130-202A include an EDID copy feature which

stores a monitor’s EDID information and sends it to the source,

ensuring optimal compatibility. If you did not store a monitor’s EDID

copy, perform the EDID copy procedure described in this manual.

Note: Because EDID copy is supposed to be performed prior to installation,

you may need to restart your computer if you perform a copy after setting

everything up.

4Have you adjusted the Equalization setting on the receiver unit?

There is a built-in Equalization adjustment knob on the receiver,

which can be adjusted to obtain the best picture quality. Use the mini

screwdriver included with the product to adjust this setting until an

acceptable image is displayed.

5What resolution are you trying to reach? The B130-202 and

B130-202A are tested to support up to 1440 x 900 @ 60 Hz video

resolution (See the Product Features section in this manual for

details on max distance and resolution). The shorter the extension

distance, the higher the resolution you will be able to obtain. If

you are not able to get an acceptable image after adjusting the

Equalization setting, try lowering your computer’s video resolution or

adjusting the refresh rate.

14-11-117-93-333B.indd 8 11/24/2014 2:51:42 PM

Troubleshooting

6What type of cabling are you using? Inferior cabling can result in poor

performance, so it is important that you use cables that can support

the video resolution you are trying to obtain. To achieve maximum

distance and resolution, 24AWG solid wire Cat5e/6 cable must be

used. Tripp Lite’s N202-Series Cat6 cables are made with 24AWG

solid wires, as are the N022-01K-GY (Cat5) and N222-01K-GY bulk

cables. For optimal image quality, use Zero-Skew cable, such as Tripp

Lite’s P524-01K. Also, the VGA cables you are using must support

the resolution you are trying to obtain. Inexpensive, low-quality VGA

cables may not support the maximum resolution. It is recommended

that you use Tripp Lite’s P502-Series VGA or P504-Series VGA +

audio cables, as they have been tested to work with Tripp Lite’s VGA

over Cat5 extender products.

7Is your Cat5e/6 cabling wired to TIA 568B? Tripp Lite’s VGA over Cat5

extender products have been tested using Cat5e/6 cabling wired to

TIA 568B (all Tripp Lite Cat5e/6 cables are wired to TIA 568B). Using

cabling that is wired differently may affect performance.

8Test your cables to ensure they are working properly. For example,

connect your VGA cables between a source and a monitor that

you know is working properly to see if the cable is functioning. For

Cat5e/6 cable, connect it between a computer and a network to

verify that it establishes a network connection. When testing your

cables, test them between the source and monitor(s) being used in

your installation. This will ensure that your source and monitor(s) are

compatible.

9Do you have any patch panels or other devices in between the

transmitter and receiver units? Tripp Lite’s VGA over Cat5 extender

products were designed to be connected directly from the transmitter

to the receiver via UTP cable. The more connection points that are

between the source and the remote monitor, the more likely signal

degradation will occur, causing poor performance. If you have a patch

panel or other device in between, it should be removed from the

installation.

14-11-117-93-333B.indd 9 11/24/2014 2:51:42 PM

Troubleshooting

Check your cabling for any damage that may have occurred during

installation. If a cable connector is loosened from pulling through

ceilings/walls, or the cable jacket is damaged, causing the wiring to

be exposed, you will not be able to achieve maximum performance.

Are the transmitter and/or receiver units located in an area

that exposes them to elevated temperatures? If the product is

overheating, it will not function properly.

Are you using a VGA to DVI adapter with this product? If so, you will

need to have it connected to a DVI source or monitor that supports

both Analog and Digital signals. If your DVI source or monitor supports

DVI-D digital signals only, you will not be able to convert it to VGA.

14-11-117-93-333B.indd 10 11/24/2014 2:51:42 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tripp Lite Extender Handbücher

Tripp Lite

Tripp Lite B203-101-PNP Bedienungsanleitung

Tripp Lite

Tripp Lite B127A-1A1-BCBH Bedienungsanleitung

Tripp Lite

Tripp Lite BHDBT-K-E3SI-ER Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1D1-WHD1 Bedienungsanleitung

Tripp Lite

Tripp Lite B165-101 Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1A1-WHD3 Bedienungsanleitung

Tripp Lite

Tripp Lite B127-002-D2H Bedienungsanleitung

Tripp Lite

Tripp Lite B127A-002-BH Bedienungsanleitung

Tripp Lite

Tripp Lite P166-001-A Bedienungsanleitung

Tripp Lite

Tripp Lite B125-101-60-IR Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1A1-WHD1 Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1A1-WP Bedienungsanleitung

Tripp Lite

Tripp Lite B203-101-PNP Bedienungsanleitung

Tripp Lite

Tripp Lite B203-104-PNP Bedienungsanleitung

Tripp Lite

Tripp Lite B127E-1A1-HH Bedienungsanleitung

Tripp Lite

Tripp Lite B203-101-IND Bedienungsanleitung

Tripp Lite

Tripp Lite B013-330 Bedienungsanleitung

Tripp Lite

Tripp Lite B127-008-D Bedienungsanleitung

Tripp Lite

Tripp Lite B127-1A1-CH Bedienungsanleitung

Tripp Lite

Tripp Lite HDMI Extender B122-000 Bedienungsanleitung

Tripp Lite

Tripp Lite B203-101-IND-ER Bedienungsanleitung

Tripp Lite

Tripp Lite B203-101 Bedienungsanleitung

Tripp Lite

Tripp Lite B013-HU-4K Bedienungsanleitung

Tripp Lite

Tripp Lite B130-101S-WP Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung