TYAN GN70-B8236 Kurzanleitung

http://www.tyan.com

GN70-B8236

Service Engineer’s Manual

http://www.tyan.com

PREFACE

This publication, including all photographs, illustrations, and software, is

Neither this manual, nor any material contained herein, may be reproduced

without written consent of manufacturer.

TYAN®is a registered trademark of MiTAC International Corporation.

Version 1.0

Disclaimer

Information contained in this document is furnished by MiTAC International

Corporation and has been reviewed for accuracy and reliability prior to

printing. MiTAC assumes no liability whatsoever, and disclaims any

express or implied warranty, relating to sale and/or use of TYAN®products

including liability or warranties relating to fitness for a particular purpose or

merchantability. MiTAC retains the right to make changes to produce

descriptions and/or specifications at any time, without notice. In no event

will MiTAC be held liable for any direct or indirect, incidental or

consequential damage, loss of use, loss of data or other malady resulting

from errors or inaccuracies of information contained in this document.

Trademark Recognition

All registered and unregistered trademarks and company names

contained in this manual are property of their respective owners including,

but not limited to the following.

TYAN®is a trademark of MiTAC International Corporation.

Intel®is a trademark of Intel®Corporation.

AMI®, AMIBIOS® and combinations thereof are trademarks of AMI

Technologies.

Microsoft®, Windows®are trademarks of Microsoft Corporation.

IBM®, PC®, AT®and PS/2®are trademarks of IBM Corporation.

Winbond®is a trademark of Winbond Electronics Corporation.

http://www.tyan.com

FCC Declaration

Notice for the USA

Compliance Information Statement (Declaration of

Conformity Procedure) DoC FCC Part 15: This

device complies with part 15 of the FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following conditions:

This device must not cause harmful interference.

This device must accept any interference received, including

interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Notice for Canada

This Class A digital apparatus complies with Canadian ICES-003. Cet

appareil numérique de la Classe A est conforme à la norme NMB-003

du Canada.

Notice for Europe (CE Mark)

This product is in conformity with the Council

Directive 2004/108/EC.

CAUTION: Lithium battery included with this board. Do not puncture,

mutilate, or dispose of battery in fire. There will be danger of explosion if

battery is incorrectly replaced. Replace only with the same or equivalent

type recommended by manufacturer. Dispose of used battery according

to manufacturer instructions and in accordance with your local

regulations.

http://www.tyan.com

About this Manual

This manual provides you with instructions on installing your TYAN

GN70-B8236. This Manual is intended for experienced users and

integrators with hardware knowledge of personal computers.

This manual consists of the following parts:

Chapter1: Provides an introduction to the TYAN GN70-B8236

barebones, standard parts list, describes the external

components, gives a table of key components, and

provides block diagram of the system.

Chapter2: Covers procedures on installing the CPU, memory

modules and hard drives.

Chapter3: Covers removal and replacement procedures for

pre-installed components.

Appendix: List the cable connection and FRU part tables for

reference of system setup, and technical support in

case a problem arises with your system.

http://www.tyan.com

Safety and Compliance Information

Before installing and using TYAN GN70-B8236, take note of the following

precautions:

·Read all instructions carefully.

·Do not place the unit on an unstable surface, cart, or stand.

·Do not block the slots and opening on the unit, which are provided for

ventilation.

·Only use the power source indicated on the marking label. If you are not

sure, contact the power company.

·The unit uses a three-wire ground cable, which is equipped with a third

pin to ground the unit and prevent electric shock. Do not defeat the

purpose of this pin. If your outlet does not support this kind of plug,

contact your electrician to replace your obsolete outlet.

·Do not place anything on the power cord. Place the power cord where it

will not be in the way of foot traffic.

·Follow all warnings and cautions in this manual and on the unit case.

·Do not push objects in the ventilation slots as they may touch high

voltage components and result in shock and damage to the

components.

·When replacing parts, ensure that you use parts specified by the

manufacturer.

·When service or repairs have been done, perform routine safety checks

to verify that the system is operating correctly.

·Avoid using the system near water, in direct sunlight, or near a heating

device.

·Cover the unit when not in use.

http://www.tyan.com

Safety Information

Retain and follow all product safety and operating instructions

provided with your equipment. In the event of a conflict between the

instructions in this guide and the instructions in equipment

documentation, follow the guidelines in the equipment documentation.

Observe all warnings on the product and in the operating instructions.

To reduce the risk of bodily injury, electric shock, fire and damage to

the equipment, observe all precautions included in this guide.

You must become familiar with the safety information in this guide

before you install, operate, or service TYAN products.

Symbols on Equipment

Caution. This symbol indicates a potential

hazard. The potential for injury exists if

cautions are not observed. Consult equipment

documentation for specific details.

Warning. This symbol indicates the presence

of hazardous energy circuits or electric shock

hazards. Refer all servicing to qualified

personnel.

Warning. This symbol indicates the presence of a

hot surface or hot component. If this surface is

contacted, the potential for injury exists.

To reduce risk of injury from a hot component,

allow the surface to cool before touching.

General Precautions

· Follow all caution and warning instructions marked on the equipment

and explained in the accompanying equipment documentation.



Machine Room Environment

 · Make sure that the area in which you install the system is properly

ventilated and climate-controlled.

http://www.tyan.com

· Ensure that the voltage and frequency of your power source match the

voltage and frequency inscribed on the electrical rating label of the

equipment.

·Do not install the system in or near a plenum, air duct, radiator, or heat

·Never use the product in a wet location.

Equipment Chassis

· Do not block or cover the openings to the system.

·Never push objects of any kind through openings in the equipment.

Dangerous voltages might be present.

·Conductive foreign objects can produce a short circuit and cause fire,

electric shock, or damage to your equipment.

·Lift equipment using both hands and with your knees bent.

Equipment Racks

To avoid injury or damage to the equipment:

·Observe local occupational health and safety requirements and

guidelines for manual materials handling.

·Do not attempt to move a rack by yourself; a minimum of two people

are needed to move a rack.

·Do not attempt to move a fully loaded rack. Remove equipment from

the rack before moving it.

·Do not attempt to move a rack on an incline that is greater than 10

degrees from the horizontal.

·Make sure the rack is properly secured to the floor or ceiling.

·Make sure the stabilizing feet are attached to the rack if it is a

single-rack installation.

·Make sure racks are coupled together if it is a multiple-rack installation.

·Make sure the rack is level and stable before installing an appliance in

the rack.

·Make sure the leveling jacks are extended to the floor.

http://www.tyan.com

·Make sure the full weight of the rack rests on the leveling jacks.

·Always load the rack from the bottom up. Load the heaviest component

in the rack first.

·Make sure the rack is level and stable before pulling a component out

of the rack.

·Make sure only one component is extended at a time. A rack might

become unstable if more than one component is extended.

To avoid damage to the equipment:

· The rack width and depth must allow for proper serviceability and cable

management.

· Ensure that there is adequate airflow in the rack. Improper installation

or restricted airflow can damage the equipment.

·The rack cannot have solid or restricted airflow doors. You must use a

mesh door on the front and back of the rack or remove the doors to

ensure adequate air flow to the system.

·If you install the Model in a rack, do not place equipment on top of the

unit. It will cause restricted airflow and might cause damage to the

equipment.

·Make sure the product is properly matted with the rails. Products that

are improperly matted with the rails might be unstable.

·Verify that the AC power supply branch circuit that provides power to

the rack is not overloaded. This will reduce the risk of personal injury, fire,

or damage to the equipment. The total rack load should not exceed 80

percent of the branch circuit rating. Consult the electrical authority having

jurisdiction over your facility wiring and installation requirements.

Equipment Power Cords

· Use only the power cords and power supply units provided with your

system. The system might have one or more power cords.

·Plug the power cord into a grounded (earthed) electrical outlet that is

easily accessible at all times.

·In all European electrical environments, you must ground the

Green/Yellow tab on the power cord. If you do not ground the

http://www.tyan.com

Green/Yellow tab, it can cause an electrical shock due to high leakage

currents.

·Do not place objects on AC power cords or cables. Arrange them so

that no one might accidentally step on or trip over them.

·Do not pull on a cord or cable. When unplugging from the electrical

outlet, grasp the cord by the plug.

·To reduce the risk of electrical shock, disconnect all power cords before

servicing the appliance.

Equipment Batteries

· The system battery contains lithium manganese dioxide. If the battery

pack is not handled properly, there is risk of fire and burns.

·Do not disassemble, crush, puncture, short external contacts, or

dispose of the battery in fire or water.

·Do not expose the battery to temperatures higher than 60°C (140°F).

·The system battery is not replaceable. If the battery is replaced by an

incorrect type, there is danger of explosion. Replace the battery only with a

spare designated for your product.

·Do not attempt to recharge the battery.

·Dispose of used batteries according to the instructions of the

manufacturer. Do not dispose of batteries with the general household

waste. To forward them to recycling or proper disposal, use the public

collection system or return them to TYAN, your authorized TYAN partner,

or their agents.

Equipment Modifications

· Do not make mechanical modifications to the system. TYAN is not

responsible for the regulatory compliance of TYAN equipment that has

been modified.

Equipment Repairs and Servicing

· The installation of internal options and routine maintenance and service

of this product should be performed by individuals who are knowledgeable

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TYAN Server Handbücher

TYAN

TYAN GT20 (B5502) Bedienungsanleitung

TYAN

TYAN KGT24-500 Kurzanleitung

TYAN

TYAN MicroServer Series Bedienungsanleitung

TYAN

TYAN GC68A-B7136 Kurzanleitung

TYAN

TYAN B8226 Kurzanleitung

TYAN

TYAN FT76-B7922 Kurzanleitung

TYAN

TYAN FS65-B5521 Kurzanleitung

TYAN

TYAN TN76A-B8242 Kurzanleitung

TYAN

TYAN GA80-B7081 Kurzanleitung

TYAN

TYAN GT24 B7016 Bedienungsanleitung

TYAN

TYAN GT90-B7113 Kurzanleitung

TYAN

TYAN GT62B-B5539 Kurzanleitung

TYAN

TYAN TA77-B7061 Kurzanleitung

TYAN

TYAN Tank GT20 B5372 Bedienungsanleitung

TYAN

TYAN Transport GX18 Bedienungsanleitung

TYAN

TYAN Transport VX50 Bedienungsanleitung

TYAN

TYAN Tank GT20 B5375 Bedienungsanleitung

TYAN

TYAN Transport GT20-B2925 Bedienungsanleitung

TYAN

TYAN TS75A-B8252 Kurzanleitung

TYAN

TYAN GT24 B8212 Bedienungsanleitung

TYAN

TYAN GT24-B7016-LE Kurzanleitung

TYAN

TYAN YR292-B5538-X4 Kurzanleitung

TYAN

TYAN TS65A-B8036 Kurzanleitung

TYAN

TYAN FT77A-B7059 Kurzanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung