Ubiquiti AirFiber 60 Bedienungsanleitung

airFiber®60 GHz Radio

with 5 GHz Backup

Model: AF60

• Package Contents

• Installation Requirements

• Hardware Overview

• Installation Overview

• airFiber 60 Configuration

• UNMS Management

• Alignment

• Installer Compliance Responsibility

• Specifications

• Safety Notices

• Electrical Safety Information

• Limited Warranty

• Compliance

• Online Resources

Package Contents

Dish Main Arm Support Arms

(Qty. 2)

Mounting

Bracket

Screw U-Clamp

Flange Nuts

(Qty. 2)

Gigabit PoE (24V, 0.5A)

with Mounting Bracket

Power Cord

Installation Requirements

• Clear line of sight between airFiber AP and station

• Clear view of the sky for proper GPS operation

• Vertical mounting orientation

• Mounting point:

• At least 1 m below the highest point on the structure

• For tower installations, at least 3 m below the top of

thetower

• Outdoor, shielded Category 6 (or above) cabling and

shielded RJ45 connectors are required for all wired Ethernet

connections.

• Surge protection should be used for all outdoor installations.

We recommend that you use two Ethernet Surge Protectors,

model ETH-SP-G2, one near the airFiber radio and the other

at the entry point to the building. The ETH-SP-G2 will absorb

power surges and safely discharge them into the ground.

Note: For guidelines about grounding and lightning

protection, follow your local electrical regulatory

codes.

LAN

≤ 1m

Hardware Overview

LEDs

LED State Status

GPS Blue

The LED will light blue when the

GPS signal strength is sufficient. This

requires a minimum of four GPS

satellite connections.

60G Blue The LED will light blue when the

60GHz link is active.

5G Blue The LED will light blue when the

5GHz link is active.

LAN

Blue

The LED will light steady blue when

an active Ethernet connection is

made to the Ethernet port and flash

when there is activity.

LED State Status

Power

Flashing

White Bootup in progress.

White

Ready for use, not connected to

Ubiquiti® Network Management

System (UNMS™). See “UNMS

Management”.

Blue Ready for use, connected to UNMS.

Steady

Blue with

Occasional

Flashing

Ready for use, unable to connect

to UNMS, check connection to

UNMSserver.

Quickly

Flashing

Blue

Used to locate a device in UNMS.

Alternating

Blue/White Firmware upgrade in progress.

Ports

6PoE IN Gigabit PoE port for handling all user traffic and

powering the device. Default IP address: 192.168.1.20.

Reset Button To reset to factory defaults, press and hold

the Reset button for more than 10 seconds while the device is

poweredon.

Installation Overview

We recommend that you configure your airFiber radio before

site installation.

airFiber 60 Configuration

Connecting Power over Ethernet

Configuring the Settings

2. Configure the Ethernet adapter on your computer with a

static IP address on the 192.168.2.x subnet.

3. Launch your web browser. In the address field, type:

http://192.168.1.20

Then press enter (PC) or return (Mac).

http://192.168.1.20

4. Enter ubnt in the Username and Password fields. Select

your Country and Language. You must agree to the Terms of

Use to use the product. Click Login.

5. Click the icon.

6. Configure the following settings:

a. For one airFiber radio, enable Access Point mode. For

the other airFiber radio (the Station), keep Access Point

disabled.

b. Enter a name in the SSID field. This should be the same

on both the AP and the Station.

c. In the WPA2 Preshared Key field, enter a combination of

alphanumeric characters (0-9, A-Z, or a-z).

Note: The key is an alphanumeric password

between 8 and 63 characters long.

7. Click Save Changes.

8. Configure each airFiber radio with a unique IP address:

a. Click the icon.

b. Review the Network settings to ensure that the AP and

Station each have a unique IP address. Each can get its

IP address via DHCP, or use the fallback IP address.

• DHCP By default DHCP client is enabled; if there is a

DHCP server on your network, the airFiber radio will

receive its address via DHCP.

• Fallback IP If you use the fallback IP address on one

radio, you must change the IP Address setting on the

other radio. The fallback IP address is: 192.168.1.20

c. Click Save Changes.

Repeat the instructions in the “airFiber 60 Configuration”

section on the other airFiber radio.

UNMS Management

You can manage your device using UNMS, which lets you

configure, monitor, upgrade, and back up your devices using a

singleapplication. Get started at www.unms.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Hardware Handbücher

Ubiquiti

Ubiquiti ER-4 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwtch 5XP Bedienungsanleitung

Ubiquiti

Ubiquiti airMAX PowerBridge M10 PBM10 Bedienungsanleitung

Ubiquiti

Ubiquiti airMAX NanoBridge M NBM3 Bedienungsanleitung

Ubiquiti

Ubiquiti Airmax NBE-M2-400 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-AE Bedienungsanleitung

Ubiquiti

Ubiquiti airMAX NanoStationM2 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-48-500W Bedienungsanleitung

Ubiquiti

Ubiquiti airVision-C Bedienungsanleitung

Ubiquiti

Ubiquiti RocketM Series Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam airMAX NBE-M5-300 Bedienungsanleitung

Ubiquiti

Ubiquiti AM-5AC21-60 Bedienungsanleitung

Ubiquiti

Ubiquiti USW-48-POE Bedienungsanleitung

Ubiquiti

Ubiquiti uFiber OLT 4 Bedienungsanleitung

Ubiquiti

Ubiquiti R5AC-PTP Bedienungsanleitung

Ubiquiti

Ubiquiti Loco5AC Bedienungsanleitung

Ubiquiti

Ubiquiti M900 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti PBM3 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi WiFi BaseStation XG Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti USW-24 Bedienungsanleitung

Ubiquiti

Ubiquiti UBB Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Flex-Mini Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung

Ubiquiti airFiber 60 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken