Ubiquiti ER-8-XG Bedienungsanleitung

8-Port 10G SFP+ Router

Model: ER-8-XG

Introduction

Thank you for purchasing the Ubiquiti Networks®

EdgeRouter™Infinity. This Quick Start Guide is designed

to guide you through installation and also includes

warrantyterms.

Package Contents

EdgeRouter Infinity

Mounting Brackets

(Qty. 2)

Bracket Screws

(Qty. 8)

Mounting Screws

(Qty. 4)

Cage Nuts

(Qty. 4)

Power Cords

(Qty. 2)

Rubber Feet

(Qty. 4)

installer’s responsibility to follow local country regulations, including operation within legal

frequency channels, output power, indoor cabling requirements, and Dynamic Frequency

Selection (DFS) requirements.

Installation Requirements

• Phillips screwdriver (for rack- or wall-mounting)

• Standard-sized, 19" wide rack with a minimum of 1U height

available (for rack-mounting)

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit:

www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric

shock, do not expose the EdgeRouter Infinity to rain

ormoisture.

Note: Although the cabling can be located outdoors,

the EdgeRouter Infinity itself should be housed inside

a protective enclosure.

Hardware Overview

Front Panel Ports

Console SFP+

(eth1-eth8)

RJ45

(eth0)

USB

microSD

Interface Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also

known as a rollover cable, to connect the

Console port to your computer. (If your

computer does not have a DB9 port, then

you will also need a DB9 adapter.) Then

configure the following settings as needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

SFP+

(eth1-eth8)

Hot-swappable SFP+ ports support

10Gbps connections.

RJ45

(eth0)

RJ45 port supports 10/100/1000 Ethernet

connections.

microSD Reserved for future use.

USB Reserved for future use.

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeRouter Infinity to factory defaults:

• Runtime reset (recommended) The

EdgeRouter Infinity should be running

after bootup is complete. Press and hold

the Reset button for about 10seconds

until the LED of port eth0 starts flashing

and then becomes solidly lit. After a few

seconds, the LED will turn off, and the

EdgeRouter Infinity will automatically

reboot.

Note: To press the Reset button,

insert a straightened paper clip (or

similar object) into the hole shown

above. Do not use an object that

can break and become lodged in

the hole.

• Power-on reset Disconnect the Power

Cords from the EdgeRouter Infinity.

Press and hold the Reset button while

connecting the Power Cords to the

EdgeRouter Infinity. The port LEDs will

light up in sequential order. Keep holding

the Reset button until the LED on the

last port starts flashing, and then release

the button.

Front Panel LEDs

SFP+:

Link/Act

RJ45:

Link/Act

System

LED State Status

System

White EdgeRouter Infinity is

powered on.

SFP+ (eth1-8)

Link/Act

Off No Link

White Link Established

White Flashing Link Activity

RJ45 (eth0)

Link/Act

Off No Link

Green Link Established

Green Flashing Link Activity

Back Panel

PSU Power Ports

Fans

Note: There are ventilation holes on the sides of the

EdgeRouter Infinity.

Hardware Installation

The EdgeRouter Infinity can be placed on a horizontal surface,

mounted on a wall, or mounted in a rack.

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

1. Attach the Mounting Brackets to the EdgeRouter Infinity

using the eight Bracket Screws.

2. Attach the EdgeRouter Infinity to the rack using the four

Mounting Screws. (If the rack has square slots, then use the

Cage Nuts with the Mounting Screws.)

3. Connect the Power Cord to one PSU Power Port.

4. Connect the other end of the Power Cord to a power outlet.

5. Repeat steps 3-4 to connect power to the second

PSUPower Port.

Connecting SFP+

1. Remove the protective plug covering the SFP+ port.

2. Plug a compatible fiber module into the SFP+ port.

1000MbpsSM/SC20KM DDM

Tx1550nm/Rx1310nm

3. Connect the fiber optic cable to the fiber module. Then

connect the other end of the cable to another fiber device.

4. Repeat steps 1-3 to connect additional SFP+ ports.

Note: Use compatible fiber SFP+ modules with the

appropriate fiber optic cabling. For information about

compatible fiber SFP+ modules, visit:

ubnt.link/SFP_DAC_Compatibility

Accessing the EdgeOS Configuration Interface

The EdgeOS® configuration interface can be accessed via

DHCP or static IP address assignment. By default, eth1 is set

up as a DHCP client, while eth0 is assigned a static IP address

of 192.168.1.1. To configure the EdgeRouter, proceed to the

appropriate section: DHCP or “Static IP Address”.

DHCP

1. Connect a cable from eth1 on the EdgeRouter to a LAN

segment that has an existing DHCP server.

2. To check the IP address of the EdgeRouter, use one of the

following methods:

• Set up the DHCP server to provide a specific IP address

to the EdgeRouter based on its MAC address (on the

label).

• Let the EdgeRouter obtain an IP address and then check

the DHCP server to see which IP address was assigned.

3. Launch your web browser. Enter the appropriate IP address

in the address field. Press enter (PC) or return (Mac).

Andere Handbücher für ER-8-XG

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Router Handbücher

Ubiquiti

Ubiquiti EdgeRouter ER-12P Bedienungsanleitung

Ubiquiti

Ubiquiti ERLite-3 Bedienungsanleitung

Ubiquiti

Ubiquiti TS-8-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti AmpliFi AFi-G Bedienungsanleitung

Ubiquiti

Ubiquiti ER-8-XG Bedienungsanleitung

Ubiquiti

Ubiquiti 3GStation Professional Bedienungsanleitung

Ubiquiti

Ubiquiti UFiber UF-WIFI Gebrauchsanweisung

Ubiquiti

Ubiquiti EdgeRouter ER-8 Bedienungsanleitung

Ubiquiti

Ubiquiti LiteStation2 Bedienungsanleitung

Ubiquiti

Ubiquiti Amplifi AFi-LR Bedienungsanleitung

Ubiquiti

Ubiquiti airCube Bedienungsanleitung

Ubiquiti

Ubiquiti ROcket M5 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-8 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti UCK-G2-PLUS Bedienungsanleitung

Ubiquiti

Ubiquiti Bullet Bedienungsanleitung

Ubiquiti

Ubiquiti UCK-G2 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter X ER-X Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UFber loco Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP PRO Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti UF-LOCO Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung