Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

5-Port Router

with Power over Ethernet

Model: ERPoe-5

https://arttel.ru/

https://arttel.ru/shop/marshrutizatory/ubiquiti-edgerouter-poe

Introduction

Thank you for purchasing the Ubiquiti Networks®

EdgeRouter™PoE 5-Port Router. This Quick Start Guide is

designed to guide you through installation and also includes

warranty terms.

Package Contents

EdgeRouter PoE Power Adapter

(48V, 1.25A)

Power Cord

5-Port Router

with Power over Ethernet

Model:ERPoe-5

Screws

(M2.9x20, Qty. 2)

Screw Anchors

(M2.9, Qty. 2)

Quick Start Guide

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

https://arttel.ru/

https://arttel.ru/shop/marshrutizatory/ubiquiti-edgerouter-poe

Hardware Overview

Front Panel Ports

Console ResetEthernet (eth0-eth4)

Interface Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use a

RJ45-to-DB9 serial console cable to connect

the Console port to your computer.

Ethernet

(eth0-eth4)

All ports can be used for routing and support

10/100/1000 Mbps connections with

configurable PoE settings. eth2, eth3, and

eth4 can be configured for switching using

the EdgeOS Configuration Interface.

Reset

There are two methods to reset the

EdgeRouter PoE to factory defaults:

• Runtime reset (recommended) The

EdgeRouter PoE should be running after

bootup is complete. Press and hold the

Reset button for about 10seconds until

the right LED on port eth4 starts flashing

and then becomes solidly lit. After a few

seconds, the LED will turn off, and the

router will automatically reboot.

• Power-on reset Disconnect the Power Cord

from the Power Adapter. Press and hold the

Reset button while connecting the Power

Cord to the Power Adapter. Keep holding

the button until the right LED on port eth4

starts flashing and then stops flashing after

a few seconds.

https://arttel.ru/

https://arttel.ru/shop/marshrutizatory/ubiquiti-edgerouter-poe

Front Panel LEDs

Power Speed/Link/ActPoE

LED State Status

Console

Power

Off Power off

Green Power on

Ethernet (eth0-eth4)

PoE

Off No Power over Ethernet

Green 24V Power over Ethernet

Amber 48V Power over Ethernet

Speed/

Link/

Act

Off No Link

Amber Link Established at

10/100 Mbps

Amber Flashing Link Activity at

10/100 Mbps

Green Link Established at

1000 Mbps

Green Flashing Link Activity at

1000 Mbps

https://arttel.ru/

https://arttel.ru/shop/marshrutizatory/ubiquiti-edgerouter-poe

Back Panel

Power

Grounding Point

Ventilation Holes

Installation Requirements

• Drill with a 6 mm drill bit (for wall-mounting)

• Phillips screwdriver

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit:

www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric shock,

do not expose the EdgeRouter to rain or moisture.

Note: Although the cabling can be located outdoors,

the EdgeRouter itself should be housed inside a

protective enclosure.

Hardware Installation

The EdgeRouter PoE can be placed on a desktop or mounted

to a wall or other surface.

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

https://arttel.ru/

https://arttel.ru/shop/marshrutizatory/ubiquiti-edgerouter-poe

Wall Mounting

To mount the EdgeRouter PoE on a wall:

1. Use a 6 mm drill bit to drill two holes 100 mm apart.

2. Insert the M2.9 Anchors into the holes. Use a Phillips

screwdriver to secure a M2.9x20 Screw to each anchor.

Leave a clearance of approximately 3 mm between each

screw head and its anchor.

100 mm

3 mm

Note: The EdgeRouter PoE may also be mounted in a

vertical orientation.

3. Position the EdgeRouter PoE with the Ethernet ports

facing down. Place the wall-mount slots of the EdgeRouter

PoE over the screw heads on the wall. Then slide the

EdgeRouter PoE down to lock it into place.

https://arttel.ru/

https://arttel.ru/shop/marshrutizatory/ubiquiti-edgerouter-poe

Grounding the EdgeRouter PoE (Recommended)

The EdgeRouter PoE is grounded through the Power Adapter;

however, you can add optional ESD grounding for enhanced

ESD protection.

1. Loosen the grounding screw and secure a ground wire (not

included) to the Grounding Point.

2. Secure the other end of the ground wire to a grounding

block or other grounded structure.

https://arttel.ru/

https://arttel.ru/shop/marshrutizatory/ubiquiti-edgerouter-poe

Connecting Power

1. Connect the Power Adapter to the Power port.

2. Connect the Power Cord to the Power Adapter. Connect the

other end of the Power Cord to a poweroutlet.

https://arttel.ru/

https://arttel.ru/shop/marshrutizatory/ubiquiti-edgerouter-poe

Accessing the EdgeOS Configuration Interface

1. Connect an Ethernet cable from the Ethernet port of your

computer to the port labeled eth0 on the EdgeRouter PoE.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet

(e.g., 192.168.1.100).

3. Launch your web browser. Type https://192.168.1.1 in the

address field, and press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Read the Ubiquiti License Agreement,

and check the box next to I agree to the terms of this License

Agreement to accept it. Click Login.

The EdgeOS Configuration Interface will appear, allowing you

to customize your settings as needed.

https://arttel.ru/

https://arttel.ru/shop/marshrutizatory/ubiquiti-edgerouter-poe

Configuring PoE Settings

The PoE setting for ports eth0-eth4 is set to Off by default.

WARNING: Before activating PoE, ensure that the

connected device supports passive PoE and the

supplied voltage.

1. In the Dashboard tab, click Actions > PoE of the Ethernet

port you want to configure.

2. The Interface Configuration window will appear. Select the

appropriate PoE setting*, and click Save.

*640-00032-03*

640-00032-03

https://arttel.ru/

https://arttel.ru/shop/marshrutizatory/ubiquiti-edgerouter-poe

Andere Handbücher für EdgeRouter PoE ERPoe-5

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Router Handbücher

Ubiquiti

Ubiquiti EdgeRouter 6P Bedienungsanleitung

Ubiquiti

Ubiquiti edgepoint r6 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter X ER-X Bedienungsanleitung

Ubiquiti

Ubiquiti 3GStation Professional Bedienungsanleitung

Ubiquiti

Ubiquiti UDM Bedienungsanleitung

Ubiquiti

Ubiquiti LiteStation2 Bedienungsanleitung

Ubiquiti

Ubiquiti airCube Bedienungsanleitung

Ubiquiti

Ubiquiti ER-8-XG Bedienungsanleitung

Ubiquiti

Ubiquiti AFi-ALN Bedienungsanleitung

Ubiquiti

Ubiquiti edgerouter X SFP Bedienungsanleitung

Ubiquiti

Ubiquiti UF-LOCO Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgePoint R8 Bedienerhandbuch

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 4 Bedienungsanleitung

Ubiquiti

Ubiquiti ER-12 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti UFber UF-WIFI Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 10X Bedienungsanleitung

Ubiquiti

Ubiquiti UCK-G2-PLUS Bedienungsanleitung

Ubiquiti

Ubiquiti UFber loco Bedienungsanleitung

Ubiquiti

Ubiquiti ToughSwitch Pro TS-80-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti ERLite-3 Bedienungsanleitung

Ubiquiti

Ubiquiti AmpliFi AFi-G Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung