Ubiquiti LTU LR Bedienungsanleitung

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Router Handbücher

Ubiquiti

Ubiquiti EdgeRouter Lte 3 Bedienungsanleitung

Ubiquiti

Ubiquiti ToughSwitch Pro TS-80-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-10X Bedienungsanleitung

Ubiquiti

Ubiquiti Amplifi AFi-LR Bedienungsanleitung

Ubiquiti

Ubiquiti AmpliFi AFi-G Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP PRO Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 4 Bedienungsanleitung

Ubiquiti

Ubiquiti edgepoint r6 Bedienungsanleitung

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-8 Bedienungsanleitung

Ubiquiti

Ubiquiti edgerouter X SFP Bedienungsanleitung

Ubiquiti

Ubiquiti 3GStation Professional Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter X ER-X-SFP Bedienungsanleitung

Ubiquiti

Ubiquiti UFber UF-WIFI Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 6P Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USG Bedienungsanleitung

Ubiquiti

Ubiquiti UCK-G2 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter ER-12P Bedienungsanleitung

Ubiquiti

Ubiquiti ER-4 Bedienungs- und Wartungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti ER-8-XG Bedienungsanleitung

Ubiquiti

Ubiquiti ER-8-XG Bedienungsanleitung

Ubiquiti

Ubiquiti EdgePoint R8 Bedienerhandbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

5 GHz Subscriber Station

Model: LTU-LR

Introduction

Thank you for purchasing the Ubiquiti®LTU™5 GHz Subscriber

Station. This Quick Start Guide is designed to guide you through

installation and also includes warranty terms.

Package Contents

LTU-LR Mount Bracket Pole Clamp

U-Bolt Flange Nuts

(Qty. 2)

Washers

(Qty. 2)

Gigabit PoE (24V, 0.5A)

with Mounting Bracket

Power Cord

Installation Requirements

• 13 mm wrench

• (Recommended) 2 Outdoor Gigabit PoE surge protectors

Note: For guidelines about grounding and lightning

protection, follow your local electrical regulatory

codes.

• Outdoor, shielded Category 6 (or above) cabling and

shielded RJ45 connectors are required for all wired Ethernet

connections.

Hardware Overview

Back Panel

LEDs

Reset Button

USB-C Port

Reset Button

To reset to factory defaults, press and hold the Reset button for

more than 10 seconds while the device is poweredon.

USB-C Port

Reserved for future use.

LEDs

5 GHz 5 GHz The LED will light blue when the 5GHz link

is active.

GPS GPS The LED will light blue when the GPS signal

strength is sufficient. This requires a minimum of

three satellite connections.

UNMS The center LED will light when there is a

connection to the Ubiquiti® Network Management

System (UNMS™) server.

LAN The LED will light steady blue when an active

Ethernet connection is made to the Ethernet port

and flash when there is activity.

Power The LED will light blue when the device is

connected to a power source.

Bottom Panel

Ethernet Port

Ethernet Port Gigabit PoE port for handling all user traffic

and powering the device. Default IP address: 192.168.1.20

Pole Mounting

1. Remove the lock nut.

2. Attach the Mount Bracket.

3. Replace the lock nut.

4. Insert the U-Bolt into the Pole Clamp.

25 - 60 mm

5. Insert the U-Bolt into the Mount Bracket. Secure the U-Bolt

with the Washers and Flange Nuts.

6. Aim the device, and then lock the aim by tightening the

Flange Nuts to a torque of 25 N ∙ m.

25 N∙m

Connecting Power

1. Remove the port cover by pressing down the center of the

cover and sliding the cover out.

2. Connect an Ethernet cable to the Ethernet port.

3. Replace the port cover.

4. Connect the power using one of the following options:

• Using the included Gigabit PoE Adapter: Go to

Connecting to the PoE Adapter.

• Using a separate PoE switch: Connect the Ethernet

cable from the device’s Ethernet port to a 24V Passive

PoE-enabled Ethernet port on the switch.

WARNING: The switch port must comply with the

power specifications listed in the Specifications

section of this Quick Start Guide.