Ubiquiti Edgepoint r6 Bedienungsanleitung

Intelligent WISP Control

with FiberProtect™

Model: EP-R6

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgePoint™

Router. This Quick Start Guide is designed to guide you through

installation and includes the warranty terms.

Package Contents

EdgePoint Router Metal Strap Gigabit PoE (24V, 1.25A) with

Mounting Bracket

Intelligent WISP Control

with FiberProtect™

Model: EP-R6

Power Cord Quick Start Guide

Installation Requirements

• Phillips screwdriver

• 7 mm socket wrench

• Ground wire – min. 10 AWG (5 mm2) and max. length: 1m. Asa

safety precaution, ground the EdgePoint to a grounded mast,

pole, tower, or grounding bar.

• Shielded Category 5 (or above) cabling should be used for all

wired Ethernet connections and should be grounded through

the AC ground of the PoE.

• We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit: www.ubnt.com/toughcable

warranty. TOUGHCable™is designed for outdoor installations. It is the customer’s responsibility to

follow local country regulations, including operation within legal frequency channels, output power,

and Dynamic Frequency Selection (DFS) requirements.

Introduction

Hardware Overview

Ports Panel

Ground

Bonding Point

Reset

Interface Description

Ground

Bonding Point Used to secure a ground wire (not included).

Reset

There are two methods to reset the EP‑R6 to

factory defaults:

• Runtime reset (recommended) The

EP‑R6 should be running after bootup is

complete. Press and hold the Reset button

for about 10seconds until the eth4 LED

starts flashing and then becomes solidly lit.

After a few seconds, the LED will turn off,

and the EP‑R6 will automatically reboot.

• Power-on reset Disconnect power from

the EP‑R6. Press and hold the Reset button

while connecting power to the EP‑R6. Keep

holding the button until the eth4 LED starts

flashing and then stops flashing after a few

seconds.

EdgePoint EP‑R6 Quick Start Guide

Power Options

Either the VDC input or PoE input is used at any one time. If both

input types are connected, only the input type with the highest

voltage will be used; the other can be used as a backup. Any of the

input options can power any of the output options.

Power Input Options

• 24VDC, 3A

• 24V, 1.4A on eth0 (PoE In)

Power Output Options

• EdgePoint (required)

• Passive 24V, 2‑Pair PoE on

eth0-eth4

The number of devices that can be powered depends on the

power consumption of the specific devices. For example, if

you provide 24VDC, 1.25A, then you have 30W of power. If the

EdgePoint uses 7W (Max. Power Consumption), then you have

23W available for passive PoE output. Please check product

specifications for the power consumption values to use in your

calculations.

DC Input

VDC

Interface Description

VDC In

Terminal block connector accepts 24VDC, 3A

input to power the EdgePoint and passive

PoEoutput.

Hardware Overview

Ports

PoE In / eth0 eth1-4

eth5 / SFP

Interface Description

PoE In/eth0

(24V PoE Out)

The RJ45 port supports 10/100/1000 Ethernet

connections and has PoE input or output

functionality:

• PoE Input Accepts 24V, 1.4A PoE input to

power the EdgePoint and PoE output.

• PoE Output You can configure the port for

24V 2‑pair PoE output.

Do NOT configure port eth0 in PoE output

mode if you are using it as a PoE input power

source.

eth1‑4

(24V PoE Out)

RJ45 ports support 10/100/1000 Ethernet

connections and passive 24V, 2‑pair PoE

output for airMAX® devices.

eth5/SFP The SFP port is hot‑swappable and supports

100 Mbps or Gigabit fiber SFP modules.

Note: For extreme temperatures, please use industrial‑grade

fiber SFP modules.

EdgePoint EP‑R6 Quick Start Guide

Front Panel LEDs

LED State Status

power

Green EdgePoint Powered On

eth0‑eth4

Speed/

Link/Act

Off No Link

Green 10/100/1000Mbps (1 Gbps) Link

Flashing Indicates Activity

PoE

Output

Off No PoE

Green 24V Passive

eth5/SFP

Speed/

Link/Act

Off No Link

Green 100/1000Mbps (1 Gbps) Link

Flashing Indicates Activity

Hardware Overview

Hardware Installation

Pole Mounting

1. Open the Metal Strap and feed it through the mounting slots

on the back of the EdgePoint.

2. Wrap the Metal Strap around the pole. Use a 7 mm socket

wrench to turn the screw clockwise and securely fasten the

strap to the pole.

3. Proceed to the Grounding the EdgePoint section.

EdgePoint EP‑R6 Quick Start Guide

Removing the Port Cover

1. Press down and remove the port cover from the EdgePoint.

2. Depending on which cables will be connected, remove the

corresponding cable feed plugs from the port cover.

Hardware Installation

Grounding the EdgePoint

Note: The ground wire should be as short as possible and

no longer than one meter in length.

1. Remove the grounding screw and secure a ground wire (not

included) to the Ground Bonding Point.

2. Secure the other end of the ground wire to a grounded mast,

pole, tower, or grounding bar.

EdgePoint EP‑R6 Quick Start Guide

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Netzwerk-Router Handbücher

Ubiquiti

Ubiquiti AiAF-5 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 6P Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter X ER-X-SFP Bedienungsanleitung

Ubiquiti

Ubiquiti AmpliFi AFi-G Bedienungsanleitung

Ubiquiti

Ubiquiti LiteStation2 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti ERLite-3 Bedienungsanleitung

Ubiquiti

Ubiquiti ROcket M5 Bedienungsanleitung

Ubiquiti

Ubiquiti ER-4 Bedienungs- und Wartungsanleitung

Ubiquiti

Ubiquiti EdgeRouter Lte 3 Bedienungsanleitung

Ubiquiti

Ubiquiti TS-8-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti airCube Bedienungsanleitung

Ubiquiti

Ubiquiti Amplifi AFi-LR Bedienungsanleitung

Ubiquiti

Ubiquiti UFiber UF-WIFI Gebrauchsanweisung

Ubiquiti

Ubiquiti ER-12 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USG Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter 6P Bedienungsanleitung

Ubiquiti

Ubiquiti 3GStation Professional Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PRO Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter X ER-X Bedienungsanleitung

Ubiquiti

Ubiquiti LTU LR Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter LITE Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBridge M3 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP PRO Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Ubiquiti edgepoint r6 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken