Ubiquiti ToughSwitch Pro TS-80-PRO Bedienungsanleitung
8-Port Power over Ethernet
Managed Switch PRO
Model: TS-8-PRO
1
Introduction
Introduction
Thank you for purchasing the Ubiquiti Networks TOUGHSwitch™
PoE PRO, model TS-8-PRO. It is part of the TOUGHSwitch series:
Name Model Description
TOUGHSwitch PoE TS-5-POE 5-port managed switch
featuring 24V PoE
TOUGHSwitch PoE PRO TS-8-PRO 8-port managed switch
featuring 24V or 48V PoE
TOUGHSwitch PoE CARRIER TS-16-CARRIER Two TOUGHSwitch PoE
PROs mounted in a rack
For more information, visit www.ubnt.com.
This Quick Start Guide is designed to guide you through the
installation of the TOUGHSwitch PoE PRO and show you how to
access the Configuration Interface.
Package Contents
Carrier Class
8-Port Power over Ethernet
Managed Switch PRO
Model: TS-8-PRO
TOUGHSwitch PoE PRO Quick Start Guide Power Cord
Installation Requirement
For outdoor applications, shielded Category 5 (or above) cabling
should be used for all wired Ethernet connections and should be
grounded through the AC ground of the power supply.
We recommend that you protect your outdoor networks from
the most brutal environments and devastating ESD attacks with
industrial-grade shielded Ethernet cable from Ubiquiti Networks™.
For more details, visit www.ubnt.com/toughcable
2
TOUGHSwitch™PoE PRO Quick Start Guide
Hardware
Back Panel
Power
Ventilation Holes
Note: There are additional ventilation holes on the top and
sides of the TOUGHSwitch.
Front Panel Ports
Management
USB Reset
1-8
Interface Description
Management
10/100 Mbps port for management. Traffic between
the Management port and numbered ports will
be limited to 10/100 Mbps and, under heavy
load, may cause performance degradation of the
TOUGHSwitch.
USB Reserved for future use.
1-8 10/100/1000 Mbps ports for switching and PoE (also
available for management by default).
Reset
To reset to factory defaults, press and hold the Reset
button for more than five seconds while the unit is
already powered on.
3
Hardware
Front Panel LEDs
Power/Link/Act
PoE
Speed/Link/Act
LED State Status
Management
Power/
Link/Act
Off No power
Amber
After bootup, the LED indicates
power. After an initial link is
established, the LED indicates a
10/100 Mbps connection. If the
link terminates, the LED turns
off until a link is re-established.
If the unit reboots, the LED will
again indicate power until a link is
established.
Amber Flashing Link activity at 10/100 Mbps
1-8
PoE
Off No Power over Ethernet
Green 24V Power over Ethernet
Amber 48V Power over Ethernet
Speed/
Link/Act
Off No link
Amber Link established at 10/100 Mbps
Amber Flashing Link activity at 10/100 Mbps
Green Link established at 1000 Mbps
Green Flashing Link activity at 1000 Mbps
4
TOUGHSwitch™PoE PRO Quick Start Guide
Hardware Installation
Place the TOUGHSwitch on a bench top or other flat surface.
Note: Keep 20 mm of clearance next to the ventilation
holes for adequate airflow.
Connecting Power
1. Connect the Power Cord to the Power port of the TOUGHSwitch.
2. Connect the other end of the Power Cord to a power outlet.
5
Hardware Installation
Connecting Ethernet
1. Connect an Ethernet cable from the Ethernet port of your
computer to the Management port of the TOUGHSwitch.
2. Connect Ethernet cables from the Ethernet ports of your
devices to the numbered ports of the TOUGHSwitch.
Note: PoE is disabled by default on all numbered ports
and is not available on the Management port. To enable
PoE on the appropriate ports, use the Ports tab in the
Configuration Interface.
6
TOUGHSwitch™PoE PRO Quick Start Guide
Accessing the Configuration Interface
Connect to the Configuration Interface by performing the
following steps:
1. Ensure that your computer (or other host machine) is
connected to the Management port on the TOUGHSwitch.
Note: By default, you can configure the TOUGHSwitch
via any port; however, we recommend the Management
port. (Access to the Configuration Interface can be
limited to the Management port only. You can configure
this setting on the Device tab.)
2. Configure the Ethernet adapter on your host system with a
static IP address on the 192.168.1.x subnet (e.g., 192.168.1.100).
3. Launch your web browser. Type https://192.168.1.20 in the
address field. Press enter (PC) or return (Mac).
4. The login screen will appear. Enter ubnt in the Username and
Password fields. Click Login.
The Configuration Interface will appear, allowing you to customize
your settings as needed. You can enable PoE on the Ports tab.
Refer to the TOUGHSwitch PoE User Guide for instructions on
configuring the TOUGHSwitch. The User Guide is available at
documentation.ubnt.com
7
Specifications
Specifications
TOUGHSwitch PoE PRO
Dimensions 210 x 185 x 41 mm
Weight 1.24 kg
Power Input 110-120VAC / 210-230VAC
Max. Power Consumption 150 W
PoE Out Voltage Range 45-48VDC / 22-24VDC
Max. PoE Wattage Per Data Port 18W
ESD Rating 24 kV Air / 24 kV Contact
PoE Method Passive
Button Reset
USB Port 2.0 Type A (Reserved for Future Use)
Processor MIPS24K 400 MHz
System Memory 64 MB
Code Storage 8 MB
Certications CE, FCC, IC
Operating Temperature -25 to 55°C (-13 to 131° F)
Operating Humidity 90% Non-Condensing
PoE Congurable Per Port
Management Port N/A
Data Ports Off/24V/48V
LEDs Per Port
Management Port Power/Link/Activity
Data Ports PoE, Speed/Link/Activity
Networking Interfaces
Management Port (1) 10/100 Ethernet Port
Data Ports (8) 10/100/1000 Ethernet Ports
8
TOUGHSwitch™PoE PRO Quick Start Guide
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can be
submerged by water.
WARNING: Avoid using this product during an electrical storm.
There may be a remote risk of electric shock from lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has
an integral safety ground wire intended for connection to a grounded
safety outlet.
a. Do not substitute the power cord with one that is not the provided
approved type. Never use an adapter plug to connect to a 2-wire
outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the
safety certification, modification or misuse can provide a shock
hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there are
questions about the installation prior to connecting the equipment.
d. Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short-circuit backup
protection.
e. Protective bonding must be installed in accordance with local
national wiring rules and regulations.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Ubiquiti Netzwerk-Router Handbücher
Ubiquiti
Ubiquiti EdgeRouter X ER-X Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi Security Gateway PRO Bedienungsanleitung
Ubiquiti
Ubiquiti EdgeRouter X ER-X Bedienungsanleitung
Ubiquiti
Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung
Ubiquiti
Ubiquiti AiAF-5 Bedienungsanleitung
Ubiquiti
Ubiquiti ER-4 Bedienungs- und Wartungsanleitung
Ubiquiti
Ubiquiti EdgeRouter 10X Bedienungsanleitung
Ubiquiti
Ubiquiti EdgeRouter PRO Bedienungsanleitung
Ubiquiti
Ubiquiti EdgeRouter LITE Bedienungsanleitung
Ubiquiti
Ubiquiti airCube Bedienungsanleitung
Ubiquiti
Ubiquiti edgepoint r6 Bedienungsanleitung
Ubiquiti
Ubiquiti ROcket M5 Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi USG Bedienungsanleitung
Ubiquiti
Ubiquiti Bullet Bedienungsanleitung
Ubiquiti
Ubiquiti ERLite-3 Bedienungsanleitung
Ubiquiti
Ubiquiti ERLite-3 Bedienungsanleitung
Ubiquiti
Ubiquiti UCK-G2-PLUS Bedienungsanleitung
Ubiquiti
Ubiquiti EdgeRouter ER-10X Bedienungsanleitung
Ubiquiti
Ubiquiti Edge Pro ERPro-8 Bedienungsanleitung
Ubiquiti
Ubiquiti EdgeRouter ER-12P Bedienungsanleitung
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise