Ubiquiti NanoStation M2 Bedienungsanleitung

Models: NanoStation M2/M5

NanoStation Loco M2/M5/M900

Introduction

Thank you for purchasing a Nanostation M series product. This is

a point-to-point CPE wireless device. This Quick Start Guide is for

use with the following models:

Model Operating Frequency Ethernet Ports

NanoStation M2 2403-2475 MHz 2

NanoStation M5 5170-5875 MHz* 2

NanoStation Loco M2 2402-2482 MHz 1

NanoStation Loco M5 5170-5875 MHz* 1

NanoStation Loco M900 904-926 MHz 1

* Only 5745-5850 MHz is supported in the USA and Canada

Package Contents

NanoStation 24v PoE

Adapter

Power Cord Mounting Ties

* Products may be different from pictures and are subject to change without notice.

Installation Requirements

• 10 mm wrench

• Shielded Category 5 (or above) cabling should be used for all

wired Ethernet connections and should be grounded through

the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Quick Start Guide

Hardware Overview

* Secondary Ethernet

Port included only on

NanoStation M2 & M5

Secondary Main

Reset

Secondary

Ethernet Port* Main

Ethernet Port

Note: Secondary Ethernet Port is capable of 24V Power over

Ethernet output which can provide power to a secondary

device. It can be enabled using the AirOS interface.

LEDs

LAN1 LAN2

Power The Power LED will light steady green when

properly connected to a power source.

LAN1 WAN/Main Ethernet The LAN1 Ethernet LED

will light steady green when an active Ethernet

connection is made to the Primary Ethernet Port and

flash when there is activity.

LAN2 LAN/Secondary Ethernet The LAN2 Ethernet LED

(on NanoStation M2/M5 only) will light steady green

when an active Ethernet connection is made to the

Secondary Ethernet Port.

Signal These LEDs display the signal strength.

Typical Deployment

LAN or Computer to

Ethernet Port labeled

LAN on PoE Adapter

Ethernet Port on Ubiquiti

Device to Ethernet Port labeled

POE on PoE Adapter

Connect the Power Cord to the

PoE Adapter and a power outlet

Note: Shielded Category 5 (or above) cabling should be

used for all wired Ethernet connections and should be

grounded through the AC ground of the PoE.

Quick Start Guide

Accessing AirOS

1. Make sure that your host machine is connected via Ethernet to

the Ubiquiti Networks device (as shown on previous page).

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet (e.g. 192.168.1.100).

3. Launch your Web browser and type http://192.168.1.20 in the

address field and press enter (PC) or return (Mac).

4. Enter ubnt in the Username and Password fields. Select your

country from the Select Your Country drop-down. To use the

product you must agree to the terms of use. To do so, click

I agree to these terms of use. Click Login.

5. The AirOS Interface will appear allowing you to customize your

settings as needed.

Ubiquiti Networks Wiki and Forum

Ubiquiti Networks has an online Wiki with Manuals, Guides, and

Information. It is located at www.ubnt.com/wiki.

Another great resource is the Ubiquiti Networks Forum. You can

post and view comments, questions, and answers with other

forum members and Ubiquiti staff at www.ubnt.com/forum.

Quick Start Guide

Installer Compliance Responsibility

Devices must be professionally installed and it is the professional

installer's responsibility to make sure the device is operated within

local country regulatory requirements.

Since Ubiquiti Networks equipment can be paired with a variety

of antennas and cables, the Antenna Gain, Cable Loss, and Output

Power fields are provided to the professional installer to assist in

meeting regulatory requirements.

Note: This product is locked to the US Country Code to

ensure compliance with FCC regulations.

Specifications

NanoStation M

Enclosure Size 29.4 x 8 x 3 cm

Weight 0.5 kg

Max Power Consumption 8 Watts

Power Supply 24V, 1A PoE Supply Included

Power Method Passive PoE (Pairs 4, 5+; 7,8 return)

Operating Temperature -30° to 75° C

Operating Frequency

M2 2403 MHz - 2475 MHz

M5 5470 MHz - 5825 MHz

Networking Interface 2 10/100BASE-TX Ethernet Ports

NanoStation Loco M

Enclosure Size 163 x 31 x80 mm

Weight 0.18kg

Max Power Consumption 5.5 Watts

Power Supply 24V, 0.5A PoE Supply Included

Power Method Passive PoE (Pairs 4, 5+; 7,8 return)

Operating Temperature -30° to 80° C

Operating Frequency

Loco M900 904 - 926 MHz

Loco M2 2412 MHz - 2462 MHz

Loco M5 5470 MHz - 5825 MHz

Networking Interface 1 10/100BASE-TX Ethernet Ports

Quick Start Guide

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the

manufacturer.

WARNING: Do not use this product in location that can be

submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and

current requirements indicated on the manufacturer’s label.

Connection to a different power source than those specified

may result in improper operation, damage to the equipment or

pose a fire hazard if the limitations are not followed.

2. There are no operator serviceable parts inside this equipment.

Service should be provided only by a qualified service

technician.

3. This equipment is provided with a detachable power cord

which has an integral safety ground wire intended for

connection to a grounded safety outlet.

a. Do not substitute the power cord with one that is not the

provided approved type. Never use an adapter plug to

connect to a 2-wire outlet as this will defeat the continuity

of the grounding wire.

b. The equipment requires the use of the ground wire as a

part of the safety certification, modification or misuse can

provide a shock hazard that can result in serious injury or

death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

Andere Handbücher für NanoStation M2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti NBE-M5-16 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-620 Bedienungsanleitung

Ubiquiti

Ubiquiti GBE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam NBE2ACN Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam M5 LBE-M5-23 Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-11 Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket R5ACL Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP--AC--HD Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-M5-620 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Enterprise AP Bedienungsanleitung

Ubiquiti

Ubiquiti PrismStation 5AC Bedienungsanleitung

Ubiquiti

Ubiquiti AF-2X Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBeam 5AC Gen 2 NBE-5AC-Gen2 Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AC AP Mesh Pro Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation 5AC Loco Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket Prism 5AC Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStatonM Series Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-Outdoor Bedienungsanleitung

Ubiquiti

Ubiquiti AMPLIFI Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung