Ubiquiti UniFi Bedienungsanleitung

802.11ac Dual-Radio AP

with Public Address System

Model: UAP-AC-EDU

Introduction

Thank you for purchasing the Ubiquiti Networks®

UniFi®802.11ac Dual-Radio AP with Public Address System.

This Quick Start Guide is designed to guide you through

installation and also includes warranty terms.

IMPORTANT: The UAP-AC-EDU requires the UniFi Controller

4.9.5

or higher, available at: downloads.ubnt.com/unifi

Package Contents

UniFi AP AC EDU Mounting Template Gigabit PoE* (48V, 0.5A)

with Mounting Bracket

802.11ac Dual-Radio AP

with Public Address System

Model: UAP-AC-EDU

Power Cord* Quick Start Guide

* Included only in the single-pack of the UAP-AC-EDU.

Installation Requirements

• CAT5/6 cable

• Phillips screwdriver

• Drywall or keyhole saw (to cut the hole in the ceiling tile)

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

System Requirements

• Linux, MacOSX, or Microsoft Windows 7/8/10

• Java Runtime Environment 1.6 (1.8 or above recommended)

• Web Browser: Google Chrome (Other browsers may have

limited functionality.)

• UniFi Controller software v4.9.5 or newer (available at:

downloads.ubnt.com/unifi)

Network Topology Requirements

• A DHCP-enabled network (for the AP to obtain an IP address

as well as for the wireless clients after deployment)

• A UniFi Cloud Key or management station running the UniFi

Controller v4.9.5 (or newer) software, located either on-site

and connected to the same Layer-2 network, or off-site in

the cloud or NOC

• For public address system capability: A compatible Android™

or iOS device located on the same Layer-2 network as the

UniFi Controller and UniFi APs

US-16-150W

USG-PRO-4

(DHCP Server)

Internet

UAP-AC-EDU UAP-AC-EDU

LAN

WAN

UniFi Cloud Key

(UniFi Controller)

UAP-AC Outdoor

Remote Access to

UniFi Controller

Sample Network Diagram

All UniFi devices support off-site management controllers.

For setup details, see the User Guide on the website:

documentation.ubnt.com/unifi

Hardware Overview

The UniFi AP AC EDU is comprised of the Speaker Assembly

and UniFi AP.

USB Cable

Speaker

Assembly

UniFi AP

Ethernet Cable

Safety

Wire

Back of the Speaker Assembly

Main Port

Clamp Bracket

Main This Gigabit Ethernet port is used to connect the power

and should be connected to the LAN and DHCP server.

Clamp Bracket The four Clamp Brackets are used to secure the

UniFi AP AC EDU to the ceiling tile.

UniFi AP Ports

Main

Port

Secondary

Port

USB

Port

Reset

Button

Cable Feed

Opening

Secondary Reserved for future use.

Reset The Reset button serves two functions for the UniFi AP:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more than five seconds.

Note: You must remove the UniFi AP from the Speaker

Assembly before you can access the Resetbutton.

Alternatively, the UniFi AP may be reset remotely via a Reset

button located on the bottom of the Gigabit PoE adapter.

Cable Feed Opening The USB and Ethernet cables feed

through this opening.

USB The USB 2.0 port is used to support the Speaker Assembly.

Main This Gigabit Ethernet port is used to carry power

anddata.

LED and Microphone

Microphone

(reserved for

future use)

Color State Status

White Steady Factory default, waiting for

integration.

Flashing Initializing.

White/

Blue Alternating

Device is busy; do not touch or

unplug it. This usually indicates

that a process such as a firmware

upgrade is taking place.

Blue

Steady

Indicates the device has been

successfully integrated into a

network and is working properly.

Quickly

Flashing

This is used to locate an AP.

When you click Locate in the UniFi

Controller software, the LED on the

AP will flash. It will also display the

location of the AP on the map.

Steady with

occasional

flashing

Indicates the device is in an isolated

state (all WLANs are brought down

until an uplink is found).

Hardware Installation

1. Remove the ceiling tile.

2. Remove the backing from the Mounting Template and place

it in the center of the ceiling tile.

242 mm

3. Cut or drill a hole around the template.

4. Rotate the UniFiAP counterclockwise to release it from the

Speaker Assembly.

5. Feed an Ethernet cable through the hole and connect it to

the Main port of the Speaker Assembly.

6. If necessary, lift and rotate the Clamp Brackets so they

remain elevated and tucked against the Speaker Assembly.

Insert the Speaker Assembly into the hole.

7. We strongly recommend that you attach the Safety Wire

(length: 430 mm) to a secure structural point using its clasp

(inside diameter: 14 mm). Do NOT attach the Safety Wire to

a T-bar in the ceiling grid.

Note: It is the installer’s responsibility to verify that

installation complies with local construction and

safety codes.

Two examples are shown below.

8. Tighten the four screws attached to the Clamp Brackets to

secure the Speaker Assembly to the ceiling tile.

9. To connect the cables:

a. Feed the cables of the Speaker Assembly through its

cable slot and the Cable Feed Opening of the UniFi AP.

b. Connect the Ethernet cable to the Main port, and

connect the USB cable to the USB port.

Andere Handbücher für UniFi

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti UniFi USW-Flex-Mini Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-M5-620 Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket 5ac PtMP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-M-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-16-120 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFI UAP-AC Bedienungsanleitung

Ubiquiti

Ubiquiti Power AP N 802.11n Bedienungsanleitung

Ubiquiti

Ubiquiti NBE--2AC--13 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Dream Machine Beacon Bedienungsanleitung

Ubiquiti

Ubiquiti PBE-5AC-400-ISO-EU Bedienungsanleitung

Ubiquiti

Ubiquiti NanoBridge M5 Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket R5ACL Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket2AC Prism Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam ac ISO Bedienungsanleitung

Ubiquiti

Ubiquiti airFiber AF-24HD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP AC Lite Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-IW-HD Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation 5AC Loco Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStationM Series Bedienungsanleitung

Ubiquiti

Ubiquiti BulletM2-HP Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-16-120 Bedienungsanleitung

Ubiquiti

Ubiquiti LTU-LR Bedienungsanleitung

Ubiquiti

Ubiquiti AF-2X Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung