Uplus Lighting 230 BEAM Bedienungsanleitung

User manual

230 BEAM

Please read the instructions carefully before use

TABLE OF CONTENTS

1. Safety Instructions……………………………………………………………………………3-4

Technical Specifications…………………………………………………………………………4

Control Menu ……………………………………………………………………………………5-6

DMX Channels ……………………………………………………………………………………7-9

Trouble Shooting…………………………………………………………………………………10

Fixture Cleaning………………………………………………………… ………………………10

STATEMENT

The product has well capability and intact packing when leave factory. All of the user should

comply with warning item and manual, any misuse cause of the damages are not included in our

guarantee, and also can not be responsible for any malfunction & problem owing to ignore the

manual.

1.Safety Instructions

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction booklet.

•Unpack and check carefully there is no transportation damage before using the unit.

•Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

•It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

•The unit is for indoor use only. Use only in a dry location.

•The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

•Disconnect main power before replacement or servicing.

•Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

•Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

•Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

•the event of serious operating problem, stop using the unit immediately.Never try to repair the unit

by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center. Always use the same type spare parts.

•DO NOT touch any wire during operation as high voltage might be causing electric shock.

Warning:

•To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

•The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

•There are no user serviceable parts inside the unit. DO NOT open the housing or attempt any

repairs yourself. In the unlikely event your unit may require service, please contact your nearest

dealer.

Installation:

•The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly

fixed to avoid vibration and slipping while operating. And make sure that the structure to which you

are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also

always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

•The equipment must be fixed by professionals. And it must be fixed at a place where is out of the

touch of people.

2.Technical Specifications

lamp: 230w (life:2200 hours Color temperature: 8000K)

Beam angle:2°

Channel mode:18 Channel

Pan scan：540°(16bit) Electric correction

Tilt scan：270° (16bit) Electric correction

Color wheel: 14 colors

Gobo: 14 gobos

8+16+24 prism

Frost

Over heat protection

Power Input: 100-240V，50/60Hz

Power Dissipation: 230W

IP level :IP20

Net weight：10.8KG

Gross weight：12kg

Packing Size: 50X34.5X36.5CM

3. 3.Control Menu

Operation

1 .Operate light with touch or KEY

The left area is TFT Displayer and touch, chick item or value with finger will to complete operation

of set light setting(parameters) or view light state.

The area on the right hand side is 4 KEY, As auxiliary input interface, if disable touch function,, the

KEYr can been choose to set the parameter.

2 .Parameter value setting

When the selected item is value need to been modified, the dialog shown in Figure 4 will popup.

Figure 4 Dialog of value setting

Modify value：Can quickly modify value via pull the slider to the desired position, or click the

button of ‘up’ or ‘down’ whit finger on the right side to set the exact desired value, another way is roll

encoder on the right hand side of panel.

Apply value：When Value had been modified, Then press the bottom of ‘apply’ in the left corner to

apply to the light, but hav’t saved；

Save Value：Any time, click on the lower right corner of the "OK" button, the setting will been saved

into internal memory.

3. Boolean parameter setting

when the selected parameters is a Boolean value (such as ON or OFF), can directly modify setting

by chick corresponding item, the setting will been saved right now.

When the parameter is a key item, chick corresponding item, a dialog shown in Figure 5 will been

popup ask for the confirm. Chick ‘sure’ to confirm.

Figure 5 Dialog of confirm

4. Sub Menu（Parameter）

Chick item of main menu, enter corresponding sub menu, shown in Figure 6, total 6 sub menu,

includes class of parameter and status:

ADDRESS：Set light DMX address.

WORKMOD：Set light work mode, master or slave mode when in auto run mode.

DISPLAY：Set display parameter, eg. select language.

TEST：Used for test light, modify DMX channel data to test function，the corresponding function

of reference channel function table.

ADVANCE：Set light running parameter.

STATUS：view light current status.

Figure 6 Parameter menu

4.DMX Channels

16 DMX512 Channel

Channel

Name

Data

Introduce

Color

0-4

White

5-9

White+Color1

10-14

Color1

15-19

Color1+Color2

20-24

Color2

25-29

Color2+Color3

30-34

Color3

35-39

Color3+Color4

40-44

Color4

45-49

Color4+Color5

50-54

Color5

55-59

Color5+Color6

60-64

Color6

65-69

Color6+Color7

70-74

Color7

75-79

Color7+Color8

80-84

Color8

85-89

Color8+Color9

90-94

Color9

95-99

Color9+Color10

100-104

Color10

105-109

Color10~Color11

110-114

Color11

115-119

Color11+Color12

120-124

Color12

125-129

Color12+Color13

130-134

Color13

135-139

Color13+Color14

140-144

Color14

145-149

Color14+White

150-200

Forwards rainbow from fast to

slow

201-255

Backwards rainbow from slow to

fast

Strobe

0-3

4-103

Fadeout slow to fast

104-107

Open

108-207

Free Strobe slow to fast

208-212

Open

213-251

Pulse Strobe slow to fast

252-255

Open

Dimmer

0-255

Dimmer intensity from 0% to 100%

Gobo

0-4

White

5-9

Gobo1

10-14

Gobo2

15-19

Gobo3

20-24

Gobo4

25-29

Gobo5

30-34

Gobo6

35-39

Gobo7

40-44

Gobo8

45-49

Gobo9

50-54

Gobo10

55-59

Gobo11

60-64

Gobo12

65-69

Gobo13

70-125

Forwards rainbow from fast to

slow

126-130

Stop

131-190

Backwards rainbow from slow to

fast

191-195

Gobo1 Shake，Slow to fast

196-200

Gobo2 Shake，Slow to fast

201-205

Gobo3 Shake，Slow to fast

206-210

Gobo4 Shake，Slow to fast

216-220

Gobo6 Shake，Slow to fast

221-225

Gobo7 Shake，Slow to fast

226-230

Gobo8 Shake，Slow to fast

231-235

Gobo9 Shake，Slow to fast

236-240

Gobo10 Shake，Slow to fast

241-245

Gobo11 Shake，Slow to fast

246-250

Gobo12 Shake，Slow to fast

251-255

Gobo13 Shake，Slow to fast

Prism

0-127

Close Prism

128-255

Insert Prism

Prism.Rot

0-127

0~400 degree

128-187

Forwards rainbow from fast to

slow

188-195

Stop

196-255

Backwards rainbow from slow to

fast

Colorful

0-127

128-255

Insert colorful

Frost

0-127

128-255

Insert frost

Zoom

0-255

Zoom Large to small

PAN

0-255

Pan movement by 540

PAN fine

0-255

Tilt movement by 270

TILT

0-255

Fine control of pan movement

TILT fine

0-255

Fine control of tilt movement

Macro Function

0-255

Close frost

Reset

100-105

Lamp Off (Over 3 seconds)

200-205

Lamp on（Over 3 seconds）

210-215

Reset XY(over 3 seconds)

220-235

Reset effect moto(over 3 seconds)

240-255

Reset all(over 3 seconds)

lamp open

200-205

open

26-100

Shut down

Led Strips

0-255

Led Strips Effect

Led Strips

Speed

0-255

Slow to Fast

5.Trouble Shooting

ollo

ing

few

oble

y occu

uring

ope

tion

. He

tion

leshooting

The

does

work

, no

ght

Check

nect

ion of p

owe

eas

ure

ins

volt

Check

pow

LED

responding

LED

on.

che

nectors,

link

ope

If th

nd no

espons

el,

che

ess

etti

s a

ity

nter

ittent

oble

che

ins

onn

ecto

PCB

nit

the

iou

ntroller

Check

or run

lon

volta

les

terfer

ence

inter

face

circui

. One

the

cha

ing

tep

moto

dam

the

nect

to th

PCB

oken.

oto

’

ive

PCB

ndition

6.Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,

smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics.

Clean with soft cloth using normal glass cleaning fluid.

Always dry the parts carefully.

Clean the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

Inhaltsverzeichnis

Andere Uplus Lighting Beleuchtungsausrüstung Handbücher

Uplus Lighting

Uplus Lighting 300 MZ-SPOT PR Bedienungsanleitung

Uplus Lighting

Uplus Lighting W1925 Bedienungsanleitung

Uplus Lighting

Uplus Lighting 4020 IP Bedienungsanleitung

Uplus Lighting

Uplus Lighting BAR 6 LASER Bedienungsanleitung

Uplus Lighting

Uplus Lighting W3725 Bedienungsanleitung

Uplus Lighting

Uplus Lighting LED PROFILE MZ Bedienungsanleitung

Uplus Lighting

Uplus Lighting COB400 ZOOM Bedienungsanleitung

Uplus Lighting

Uplus Lighting IP MATRIX 5 Bedienungsanleitung

Uplus Lighting

Uplus Lighting 19X15Z WASH Bedienungsanleitung

Uplus Lighting

Uplus Lighting 20 MINI SPOT Bedienungsanleitung

Uplus Lighting

Uplus Lighting DUAD540 STROBE Bedienungsanleitung

Uplus Lighting

Uplus Lighting 200 BLINDER Bedienungsanleitung

Uplus Lighting

Uplus Lighting 250 LED BEAM Bedienungsanleitung

Uplus Lighting

Uplus Lighting BL6 Bedienungsanleitung

Uplus Lighting

Uplus Lighting 10X30 COB BAR Bedienungsanleitung

Uplus Lighting

Uplus Lighting BR360 Bedienungsanleitung

Uplus Lighting

Uplus Lighting MH12X40 PIXEL BAR Bedienungsanleitung

Uplus Lighting

Uplus Lighting 37X15ZWASH Bedienungsanleitung

Uplus Lighting

Uplus Lighting IP-L360 Bedienungsanleitung

Uplus Lighting

Uplus Lighting IP 300Z SPOT-WW Bedienungsanleitung

Uplus Lighting

Uplus Lighting IR 1210 PAR Bedienungsanleitung

Uplus Lighting

Uplus Lighting 200 MZ-SPOT PR Bedienungsanleitung

Uplus Lighting

Uplus Lighting IP-Z740 Bedienungsanleitung

Uplus Lighting

Uplus Lighting IP1000 Strobe Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung