Vacmaster VJS1211 Bedienungsanleitung

Wet/Dry Vacuums

Operator’s Manual

Model No.

VJS1211

FOR YOUR SAFETY

Read and understand this manual before use

Keep this manual for future reference

Cleva North America

44 Parkway Commons, Greer, SC 29650 Part No.VJ32SR.00.02

TABLE OF CONTENTS

SECTION PAGE

Warranty……………………………………………………………………………………………….

Safety Instructions and Warnings…………………………………………………………………..

Double Insulation Instructions....……………………………………………………………………

Extension Cord……………………………………………………………………………………….

Unpacking and Checking Carton Contents………….……………………..………………………

General Assembly Instructions……………………………………………………………………...

Dry Vacuum Operation……………………………………………………………………………….

Wet Vacuum Operation………………………………………………………………………………

Blowing Operation…………………………………………………………………………………...

Maintenance…………………………………………………………………………………………..

Installing & Cleaning Cartridge Filter……………………………...………………..….…………..

Installing & Cleaning Foam Sleeve Filter………………………...………………….…..….……..

Troubleshooting………………………………………………………………………………………

Exploded View and Parts List…………………………………………………………..…………..

Thank you for purchasing this Vacmaster™ wet/dry vacuum cleaner. Feel confident that with

Vacmaster™ you are obtaining a high quality product engineered for optimal performance. This

vacuum is capable of picking up liquids and dry materials.

FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS

WARRANT

Vacmaster™ takes pride in producing a high quality, durable product. This Vacmaster™ product carries a

limited two (2) year warranty against defects in workmanship and materials from date of purchase under

normal household use. If product is to be used for commercial, industrial or rental use, a 90 day limited

warranty will apply. Warranty does not apply to defects due to direct or indirect abuse, negligence, misuse,

accidents, repairs or alterations and lack of maintenance. Please keep your receipt as proof of purchase.

This warranty gives you specific legal rights, and you may have other rights, which vary form state to state.

For product service call Customer Service at (866) 384-8432

WARNING: THE POWER CORD ON THIS PRODUCT CONTAINS LEAD, A CHEMICAL KNOWN IN

THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

WASH HANDS AFTER HANDLING.

SAFETY INSTRUCTIONS & WARNINGS

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all instructions before using this vacuum

Read and understand this owner’s manual and all labels on the Wet/Dry Vacuum cleaner before operating.

Safety is a combination of common sense, staying alert and knowing how your vacuum works. Use this

Wet/Dry Vac only as described in this manual. To reduce the risk of personal injury or damage to your

Wet/Dry Vac, use only Vacmaster™ recommended accessories.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

• Do not run vac unattended.

• Do not vacuum, or use this Wet/Dry Vac near flammable liquids, gases, or explosive vapors like gasoline

or other fuels, lighter fluids, cleaners, oil-based paints, natural gas, hydrogen, or explosive dusts like coal

dust, magnesium dust, grain dust, or gun power. Sparks inside the motor can ignite flammable vapors or

dust.

• Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Keep cord away from heated surfaces.

• Do not expose to rain. Store indoors.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not use with damaged cord, plug or other parts.

• If your Wet/Dry Vac is not working as it should, has missing parts, has been dropped or damaged, left

outdoors or dropped into water, return it to an independent service center.

• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or

corners.

• Do not run Wet/Dry Vac over cord.

• Do not handle plug or the Wet/Dry Vac with wet hands.

• To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials.

• Do not use or store near hazardous materials.

• Do not use this Wet/Dry Vac with a torn filter or without the filter installed except when vacuuming liquids

as described in the operation section of this manual.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter.

• Do not leave Wet/Dry Vac unattended when plugged in. Unplug from outlet when not in use and before

servicing.

•Turn off Wet/Dry Vac before unplugging.

• Do not put any object into ventilation openings. Do not vacuum with any ventilation openings blocked;

keep free of dust, lint, hair or anything that may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• To reduce the risk of falls, use extra care when cleaning on stairs.

When using as blower:

• Direct air discharge only at work area.

• Do not use Wet/Dry Vac as a sprayer.

• Do not direct air at bystanders.

• Keep children away when blowing.

DOUBLE INSULATION INSTRUCTIONS

This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use only

identical replacements parts. Read the instructions for Servicing Double-Insulated Wet/Dry Vacs before

servicing. Use this Wet/Dry Vac as described in this manual.

Observe the following warnings that appear on the motor housing of your Wet/Dry Vac.

DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE ONLY

IDENTICAL REPLACEMENT PARTS.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-DO NOT EXPOSE TO RAIN. STORE

INDOORS.

WARNING: FOR YOUR OWN SAFETY, READ AND UNDERSTAND OPERATOR’S MANUAL. DO NOT

RUN UNATTENDED. DO NOT PICK UP HOT ASHES, COALS, TOXIC, FLAMMABLE OR OTHER

HAZARDOUS MATERIALS, DO NOT USE AROUND EXPLOSIVE LIQUIDS OR VAPORS.

CAUTION:

• Do not vacuum drywall dust or fireplace soot or ash with standard Wet/Dry filter. This is a very fine dust

which will not be captured by the filter and may cause damage to motor. Refer to operation section for

proper filter selection.

WARNING: SERVICING OF DOUBLE-INSULATED WET/DRY VACUUMM

WITH A DOUBLE-INSULATED WET/DRY VACUUM, TWO SYSTEMS OF INSULATION ARE PROVIDED

INSTEAD OF GROUNDING. NO GROUNDING MEANS IS PROVIDED ON A DOUBLE-INSULATED

APPLIANCE, NOR SHOULD A MEANS FOR GROUNDING BE ADDED. SERVICING A DOUBLE

INSULATED WET/DRY VACUUM REQUIRES EXTREME CARE AND KNOWLEDGE OF THE SYSTEM,

AND SHOULD BE DONE ONLY BY QUALIFIED SERVICE PERSONNEL. REPLACEMENT PARTS FOR

A DOUBLE-INSULATED WET/DRY VACUUM MUST BE IDENTICAL TO THE PARTS THEY REPLACE.

YOUR DOUBLE-INSULATED WET/DRY VAC IS MARKED WITH THE WORDS ‘DOUBLE INSULATED’

AND THE SYMBOL (SQUARE WITHIN A SQUARE) MAY ALSO BE MARKED ON THE

APPLIANCE.

• For Household Use Only.

• To reduce the risk of electric shock-unplug before cleaning or servicing.

• DO NOT use without filters in place.

CAUTION: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS- UNPLUG BEFORE

SERVICING.

EXTENSION CORDS

When using an extension cord with your Wet/Dry Vac refer to the following table to determine the required

A.W.G. wire size. Before using the cleaner make sure the power cord and extension cord are in good

working conditions. Make repairs or replacements before using the vacuum cleaner.

Length of Extension Cord

110V-120V 25 Feet

7.5 Meter 50 Feet

15.25 Meters 100 Feet

30.5 Meters 150 Feet

45.7 Meters

Amps A.W.G Wire Size

0-6 18 16 16 14

7-10 18 16 14 12

11-12 16 16 14 12

13-16 14 12 Not recommended

UNPACKING AND CHECKING CARTON CONTENTS

Remove entire contents of carton. Check each

item against the carton contents list.

Carton contents lists

Key Description……………………..……QTY

A Vac Assembly.…………………….…….

B Flex Hose………………………………...

C Utility Nozzle..………………………..…..

D Noise Diffuser……………………………

E Floor Brush/Squeegee………..……….

F Crevice Nozzle.………………….….……

G Extension Wands………….…………….

H Air Regulator Handle………..…………..

I Cartridge Filter.………………..…………

J Filter Retainer.…………………………..

K Foam Sleeve.………………….…….…..

L Caster.…………………………........……

M Locking Caster…………………………..

N Rear Wheels……….….……………...…

O Hub Caps….. ….……………………..….

P ‘R’ Lock Pins……………..……...……....

Q Washers………………………………..…

R 4 Screws (Bag)…………………….……

S Wheel Shaft.……………………………..

T Push Handle…………………………….

U Accessory Pouch…………………..…..

V Hose Holder…………………………….

WOperator’s Manual……..…………….…

GENERAL ASSEMBLY INSTRUCTIONS

A Philips head screw driver is required.

WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS

DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC

UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY

1. Verify that the power cord is disconnected from the outlet. (fig.1)

2. Undo the latches. (fig.2)

3. Lift the power head off the container. (fig.3)

4. Remove the contents from inside the container, make sure you have all contents as listed on page 5.

(fig.4)

5. With the power head removed, turn the container upside down. Insert the two casters into the socket on

to bottom of the castor feet and apply pressure until castors snap into place. (fig.5)

6. Insert the rear wheel shaft (S) into the rear support block. Insert washer (Q) on the shaft, then insert rear

wheel (N) on the shaft. Insert the ‘R’ lock pin (P) into the hole on the end of the shaft to lock the wheel.

Snap the hub cap (O) on to the wheel. Repeat the same steps at the other end of the shaft. (fig. 6)

7. Insert the push handle into the handle sockets mounted on the sides of the tank. Push down until the lock

pin clicks in place. (fig. 7)

8. Your vacuum comes ready for dry vacuum cleaning. If cartridge filter is not installed refer to page 10 for

filter installation.（fig. 8 & fig.9）

9. For wet vacuum cleaning, install the supplied foam filter. (fig.10) See page 10 for filter installation.

10. Place the power head back on the container, aligning the top section with the latches, and snap into

place by applying down pressure. (fig.11)

11. Insert the locking end of the hose into the vacuum port on the power head and lock in place. (fig.12)

12. Choose the desired accessories and push onto the extension tube or end of hose. (fig.13)

NOISE DIFFUSER

For quiet operation, install the noise diffuser into the blower port by inserting the locking

end of the diffuser into the blower port and turning clockwise to lock into place.

POLARIZED PLUG

To reduce the risk of electrical shock, this appliance has a double polarized plug (one with the blade wider

than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not

change the plug in any way. Double insulation eliminates the need for the three wire grounded power

cord and grounded power supply system.

ACUUM OPERATION

DRY VACUUMING

WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY

INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS,

OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT

LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE,

ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO;

COAL, MAGNESIUM, GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS

FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.

1. Verify that the power cord is disconnected from the outlet. (fig.1)

2. In order to prepare your vacuum for dry vacuuming, verify that the cartridge filter is securely mounted.

Make sure the filter is pushed in until it stops against the power head. (fig.2) (Your Wet/Dry Vac comes

with the cartridge filter pre-installed, if not see page 10 for installation instructions.)

3. Place filter retainer on top of cartridge filter and tighten down by turning the retainer handle clockwise.

(fig.3)

4. Place the power head back on the container, aligning the top section with the latches, and snap into

place by applying down pressure. (fig.4)

OPERATING INSTRUCTIONS: DRY VACUUMING

5. Insert the locking end of the hose into the vacuum port on the power head and lock in place. Push the

required attachment onto the free end of the hose or extension. (fig.5)

6. Plug in the power cord into the outlet. (fig.6)

7. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig.7)

8. Once you have completed vacuuming, flip the switch to the ‘O’ OFF position and unplug the power cord

from the outlet.

O = OFF I = ON

DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING.

WET-

ACUUM OPERATION

LIQUID VACUUMING

WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED ‘SAFETY

INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES, VAPORS,

OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT ARE NOT

LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE,

ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO;

COAL, MAGNESIUM, GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS

FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.

WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS

DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC

1. Verify that the power cord is disconnected from the outlet. Verify that the container is clean and free of

dust and dirt. (fig.1)

2. Remove cartridge filter, then carefully install the foam sleeve filter over the filter cage and place the

power head back on the container. (fig.2) See filter installing instructions on page 10.

DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING.

OPERATING INSTRUCTIONS – WET VACUUMING

3. Fit the desired nozzle to the vacuum hose. (fig.3)

4. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet. (Fig.4)

5. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig.5)

6. After use, empty the container by unscrewing the drain cap. Drain liquids into a suitable receptacle or

drain. Remember to refit the drain cap to the container after draining container. (fig.6)

IMPORTANT! When vacuuming large quantities of liquids, do not immerse the nozzle completely in the

liquid; leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float valve

that stops the suction action when the container reaches its maximum capacity. You will notice an increase

in motor speed. When this happens, turn off the machine, disconnect from power supply, and drain the

liquid into a suitable receptacle or drain. To continue vacuuming, refit the container with the drain cap. After

wet vacuuming, turn the machine off and remove plug from power supply. Empty the container, clean and

dry the inside and outside before storage.

REMEMBER! The foam filter must be removed after wet vacuuming, and a cartridge filter must be

installed before dry vacuuming again.

BLOWING OPERATION

WARNING: ALWAYS WEAR SAFETY GOGGLES COMPLYING WITH ANSI Z87.1 (OR IN CANADA,

CSAZ94.3) BEFORE USING BLOWER.

WARNING: KEEP BYSTANDERS CLEAR FOR BLOWING DEBRIS.

WARNING: WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE INHALED.

1. Verify that the power cord is disconnected from the outlet. (fig. 1)

2. Make sure the container is empty before using as a blower.

3. Remove hose from the vacuum port.

4. Remove noise diffuser form blower port. (fig. 2)

5. Insert the locking end of the hose into the blowing port on the back side of the power head and lock into

position. (fig. 3)

6. Fit the desired extension wand and or nozzle to the vacuum hose. (fig. 4)

7. Ensure the power switch is turned off and plug in the power supply. (fig. 5)

8. Before turning on the vac, firmly hold loose end of the hose. Turn the motor on by flipping the switch to

the ‘I’ ON position. (fig. 6)

MAINTENANCE

1. Verify that the power cord is disconnected from the outlet. (fig.1)

2. Disconnect the hose from the vacuum. (fig.2)

3. Undo the latches and remove the power head from the container. (fig.3)

4. Clear all dirt or debris from the container and hose. (fig.4)

5. Clean the foam filter by washing it with water and mild soap. (fig.5)

6. Check the hose, attachments, and power cord to verify that they have not been damaged.

IMPORTANT! Clean or change the cartridge filter regularly for best performance. ALWAYS USE

CARTRIDGE FILTER FOR DRY VACUUMING. If the machine is used with out the cartridge filter, the

motor will burn out and the warranty will be voided. Always keep spare filters on-hand.

NOTICE! The filters included are made of high quality materials designed to stop small dust particles. The

cartridge filter should be used for dry pick-up only. A dry cartridge filter is necessary to pick up dust. If the

cartridge filter is wet, it will clog quickly and be very difficult to clean. Handle the filter carefully when

removing it for cleaning and replacing it. Check the filters for tears or small holes, a small hole can let dust

pass through and out of the cleaner. Do not use a filter with holes or tears, replace it immediately.

WARNING! ALWAYS DISCONNECT THE PLUG FROM THE POWER OUTLET BEFORE REMOVING

THE POWER HEAD FROM THE CONTAINER.

INSTALLING & CLEANING CARTRIDGE FILTERS

Installing Cartridge Filter

1. Remove power head and place in upside down position.

2. Slide the cartridge filter down over the filter cage and carefully push filter in until it stops against the

power head. (ﬁg.1 & 2)

3. Place filter retainer on top of cartridge filter and tighten down by turning retainer handle clockwise.

(fig.3 & 4)

Removing and Cleaning Cartridge Filter

1. Unlock and remove the filter retainer by tuning retainer handle counter clockwise.

2. Carefully hold and pull the cartridge filter up for removal. (ﬁg.5)

3. Clean the cartridge filter by gently tapping or brushing dirt off. Cleaning should not be done indoors in

living areas. For optimal performance a new filter is recommended.

4. Install cleaned or new filter into place as instructed above in steps 2 and 3 of Installing Cartridge Filter.

5. Wet filters should be removed and allowed to air dry for 24 hours before installing onto the filter cage.

INSTALLING & CLEANING FOAM SLEEVE FILTER

Installing Foam Sleeve Filter

1. Remove power head and place in upside down position. Follow instructions to remove cartridge filter.

2. Carefully slide foam sleeve filter down over the filter cage making sure the whole cage is covered.

(ﬁg.1 & 2)

3. Replace the power head on to the container.

Inhaltsverzeichnis

Andere Vacmaster Staubsauger Handbücher

Vacmaster

Vacmaster VJ607 Bedienungsanleitung

Vacmaster

Vacmaster VK1638SWC Bedienungsanleitung

Vacmaster

Vacmaster VZA0708P Bedienungsanleitung

Vacmaster

Vacmaster VOM205P Bedienungsanleitung

Vacmaster

Vacmaster VBV1210 Bedienungsanleitung

Vacmaster

Vacmaster VSH01 Bedienungsanleitung

Vacmaster

Vacmaster VJC809PF Bedienungsanleitung

Vacmaster

Vacmaster VJC507P Bedienungsanleitung

Vacmaster

Vacmaster VF408 Bedienungsanleitung

Vacmaster

Vacmaster VBVA1010PF Bedienungsanleitung

Vacmaster

Vacmaster VK609PFR 0201 Bedienungsanleitung

Vacmaster

Vacmaster VJH2012PF 1101 Bedienungsanleitung

Vacmaster

Vacmaster VQ1220PF Bedienungsanleitung

Vacmaster

Vacmaster VOM205P Bedienungsanleitung

Vacmaster

Vacmaster VOC1218PF Bedienungsanleitung

Vacmaster

Vacmaster VSB1801NA Bedienungsanleitung

Vacmaster

Vacmaster VJH1612PF 0201 Bedienungsanleitung

Vacmaster

Vacmaster VK811PH Bedienungsanleitung

Vacmaster

Vacmaster UB0212EUK Bedienungsanleitung

Vacmaster

Vacmaster VJF607PF 1101 Bedienungsanleitung

Vacmaster

Vacmaster VQ607SFD Bedienungsanleitung

Vacmaster

Vacmaster VSD1801 Bedienungsanleitung

Vacmaster

Vacmaster VQ1530SFDC Bedienungsanleitung

Vacmaster

Vacmaster VMVQ1220SS Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung