VarTech Systems VT064P Bedienungsanleitung

VT064 DiamondVue User Guide 150-025

VT064 Series

6.4” Flat Panel Series LCD Monitors

Model Numbers:

VT064P · VT064P-SS

VT064PHB

VarTech Systems Inc.

Solutions for Demanding Applications

Industrial CRT and Flat Panel Displays

User’s Guide

Read these instructions completely before attempting to operate your new Color Display.

VT064 DiamondVue User Guide 150-025

Table Of Contents

Page Page

Section 1 Section 4

Introduction 1 Touch screen 11

1.1 About LCD Monitors 1 4.1 Introduction 11

1.2 Product Safety Precautions 2 4.2 Installation 11

Section 2 Section 5

Display Setup 3 Troubleshooting Tips 12-13

Display Features 3

2.1 Unpacking The Display 4 Section 6

2.2 Included Parts 4 Cleaning & Maintenance 14

2.3 Connecting Your Display 4

2.4 Signal Connections 4-6 Section 7

Mechanical Drawings 15

Section 3 7.1 Panel Mount Procedure 15

Getting Started 7 6.4” Panel Mount Mechanical Drawing 16

3.1 Adjusting the Display 7

3.2 Adjustment Procedure 8-10 Section 8

Display Specifications 20

VT064 DiamondVue User Guide 150-025

LCDs

INTRODUCTION

Section

About LCD Monitors

What you gain by using an LCD monitor in your industrial controls

1.1

are the future of display technology. Although CRTS have dropped in

cost significantly, they do not offer the performance, reliability, and

mounting options available with LCDs. LCD monitors consist primarily of

an LCD, Video Board and a Back Light video. The LCD determines to a

large extent the viewing angle, brightness and contrast. Beyond that it is

the function of the video board which converts the analog RGB (Red, Green, Blue) signals from a

standard video card to a high quality, digital RGB that the LCD can display.

Recently the video card has taken on a new role. It is the responsibility of this device to “scale” a

particular video resolution to the “native” resolution of the LCD. Simply, consider that a computer is

putting out a VGA [640x480] resolution signal, yet the LCD that is connected is an XGA

[1024x768] display. The displayed picture would be in the center 1/3 of the LCD. With the

introduction of the scaling engine. The converter will mathematically recalculate the 640x480 to

1024x768. This may sound simple but it is in fact a complex algorithm that adjusts for different

aspect ratios and pixel alignment, essentially smoothing text and graphics to produce a picture

that is pleasant to the eye.

All Vartech displays from 12.1” (800x600) to 23.1 (1600x1200) incorporate scaling engines in the

converter card.

VT064 DiamondVue User Guide 150-025

Product Safety Precautions

⇒ Ensure that sufficient space is available around the display to provide the circulation

necessary for cooling.

⇒ Ensure that the ambient air temperature will not exceed the specified maximum

temperature.

⇒ Do not attempt to service this display yourself. The rear chassis has a seal so that non

qualified personal will not expose themselves to dangerous voltages or other risks.

⇒ To protect from electrical shock, unplug the display power supply from the wall before

moving.

⇒ Do not expose the display to direct sunlight or heat.

⇒ Do not use this display near water

⇒ Do not place any heavy objects on the power cords. Damage may cause electrical shock.

⇒ Unplug the power supply from the wall or unit if one of the following conditions exists.

⇒ Power cord or plug is damaged or frayed

⇒ Liquid is spilled into the display or the display is exposed to rain or water.

⇒ The display does not operate normally when the operating instructions are

followed.

⇒ The display has been dropped or the enclosure has been damaged.

⇒ The display exhibits a distinct change in performance, indicating a need for

service.

1.2

VT064 DiamondVue User Guide 150-025

VT064 Series Display Features

⇒ The VT064 is capable of displaying 256K colors in a continuous spectrum. The high contrast

LCD enhances the image with no geometric distortion.

⇒ The VT064 Series directly accepts an analog 5 wire RGB with separate H/V.

⇒ The VT064 Series is set to VGA 640 x 480.

⇒ The VT064 Series is available in Panel Mount or Chassis Mount industrial packages.

⇒ The VT064 Series is supplied with a Anti-Reflective Screen unless equipped with an optional

Touch System.

⇒ The VT064 Series has a +12V DC jack. Vartech provides an optional 115/220VAC “Brick”

supply.

2.1

Section

DISPLAY SETUP

VT064 DiamondVue User Guide 150-025

2.2 Unpacking and setting up your display

Your LCD monitor package will consist of the components listed below. Open shipping

container and lay all components on a flat clean surface.

2.3 What is included with your display

2.4 Connecting the Display

⇒ VT064P, or VT064C LCD Monitor

⇒ 5 ft Video Cable.

⇒ +12VDC power connection. (115/220VAC “Brick” Power Supply is optional)

⇒ 10-32 Mounting Hardware. (For use with Panel Mount only)

⇒ 6 ft RS232 Touch Interface Cable (Optional when touch is installed)

⇒ CD ROM with Touch Screen Drivers (Optional when touch is installed)

⇒ Users Manual

1. Connect all cables to the computer first. This would include the VGA cable and the optional

RS 232 serial touch screen connection.

2. After connecting the cables between the LCD monitor and the computer, plug the customer

supplied +12VDC source to the 12V connection on the rear.

3. Once the +12V connection is made, the display is active.

4. If your computer was off, turn on your computer.

5. Your display should now operate as a normal computer display showing your windows or

whatever video is being sent to the flat panel.

Note: If for any reason the display goes blank and gives an “out of Range” or “No Input Signal”,

your computer or video source is putting out a signal that is out of range of the LCD’s video

board. If this happens, reboot the computer or video source and make sure you are inputting

the correct signal. If the display doesn’t work properly, it may be because:

(a) The resolution is to high or low for the LCD.

(b) The refresh rate is set to high. Refresh on an LCD is different than a CRT. Set the refresh to

60Hz. CRT’s need a high refresh rate to avoid flicker. The refresh rate has no impact on

LCD’s.

(d) The unit is malfunctioning. If you believe this to be true, disconnect the video cable from the

rear of the LCD and connect to a known good computer CRT display. If the computer

display is working satisfactory and the video is within the appropriate range, then contact

Vartech Customer service for a RMA number at 800-223-8050.

2.5 Signal Connections

To avoid irregular operation and /or damage to the display, please insure correct video is being

supplied as shown on the following page.

VT064 DiamondVue User Guide 150-025

2.5 Signal Connections Cont.

Standard Resolution Supported

⇒ 640 x 480 (VGA)

Pin assignments for the HD15

video connector.

1 Red Video

2 Green Video

3 Blue Video

4 Not Used

5 Return

6 Red Video Ground

7 Green Video Ground

8 Blue Video Ground

9 No Connection

10 Sync Ground

11 Not Used

12 Bi-Directional Data

13 Horizontal Sync

14 Vertical Sync

15 Data Clock (SCL)

Composite Video Input Connector: CVBS 1.0V p-p

S-Video: S-VHS

LUMA Signal Input 0.7V p-p

CHROMA Signal Input 0.7V p-p

You can use an HD-15 connector cable or a BNC adapter cable to connect the flat panel

monitor to the host computer. The HD-15 video cable (supplied in the kit) you use with this

monitor is equipped with a conventional HD-15 connector at each end.

Note:

The following figure is the view looking into the pin end of the male connector or solder term

end of the female connector.

VT064 DiamondVue User Guide 150-025

Optional BNC Adaptor Cable

A 5BNC-to-HD15 adapter cable is available. The functions of the cables are described below.

⇒ R, B, and G: Red, Green, and Blue input connectors to establish color.

These are used for RS-343 analog signals.

⇒ HS/CS: Separate horizontal/composite sync signal from the video

source.

⇒ VS: Separate vertical sync signal from the video source.

BNC Adapter Cable

This table describes the signal types you can use with the connectors:

2.5 Signal Connections Cont.

BNC Signal Type Description R G B HS/ CS VS

Sync-on-Green

(Not Available)

Use the three video connectors.

Horizontal and vertical syncs are

supplied on the green video line.

X X X

Composite Sync

(Not available)

Use the three video connectors

plus the horizontal sync/

composite sync input

X X X X

Separate Horizontal

and Vertical Sync.

Use the three video connectors

plus the horizontal sync/

composite sync and vertical sync

input.

X X X X X

BNC Signal Types

VT064 DiamondVue User Guide 150-025

Adjusting the display

GETTING STARTED

Section

The VT104 Series display has an embedded microprocessor in the converter card. Once you

have the unit displaying the resolution you desire for your application do the following:

In order to navigate to the appropriate adjustments, press Menu and the OSD layout chart will

appear as indicated in Fig. 1 from left to right.

If you press the “MENU” the new settings are saved and the OSM appear and your setting will

be stored in the unit’s non volatile memory.

SelectMenu

Vartech Systems

www.vartechsystems.com

3.1

Definition of OSD (on screen display) Adjustments

There are four membrane buttons (as shown above) located on the rear of the unit. They will

activate the OSD and allow navigation to all adjustments if your unit requires adjustment.

OSD Layout

Main Menu Sub Adjustment

Automatic Adjust Geometry & Color Balance

Horizontal Position Horizontal position

Vertical Position Vertical Position

Horizontal Size Horizontal Size

Phase Phase

Brightness Brightness

Contrast Contrast

Color Red, Green, Blue

OSD Language English, Espanol, Deutsch, Francais, Italiano

Advanced Factory Preset, OSD Hor. Pos., OSD Vert. Pos.

Cancel

VT064 DiamondVue User Guide 150-025

3.2 Adjustment Procedure

Feature Adjustment Instructions

Automatic

Adjustment

Press Menu and the automatic adjustment will be the first item to appear on the

OSD.

Hit Select and then press the Up/Down button to navigate to Geometry.

Press Select again and the display will automatically adjust the geometry.

Press the Up/Down button to Color Balance.

Hit Select again and the display will automatically preset the color balance to a

factory preset value.

Horizontal

Position

Press Menu.Press the Up button to the second icon which is Horz. Pos

Hit Select and then press the Up/Down button to achieve the desired position.

The desired value will be graphically illustrated along with a digital value.

When complete press Select and you are ready to move to the next adjustment.

Vertical

Position

Press Menu.Press the Up button to the third icon which is Vertical Position.

Hit Select and then press the Up/Down button to achieve the desired position.

The desired value will be graphically illustrated along with a digital value.

When complete press Select and you are ready to move to the next adjustment.

Horizontal

Size

Press Menu.Press the Up button to the fourth icon which is Horizontal Size.

Hit Select and then press the Up/Down button to achieve the desired size.

The desired value will be graphically illustrated along with a digital value.

When complete press Select and you are ready to move to the next adjustment.

Phase

Press Menu.Press the Up button to the fifth icon which is Phase.

Hit Select and then press the Up/Down button to achieve the desired phase.

The phase should be adjusted until the screen image is sharp and there is no

When complete press Select and you are ready to move to the next adjustment.

Brightness

Press Menu.Press the Up button to the sixth icon which is Brightness.

Hit Select and then press the Up/Down button to achieve the desired brightness

level.

The desired value will be graphically illustrated along with a digital value.

When complete press Select and you are ready to move to the next adjustment.

Contrast

Press Menu.Press the Up button to the seventh icon which is Contrast.

Hit Select and then press the Up/Down button to achieve the desired contrast level.

The desired value will be graphically illustrated along with a digital value.

When complete press Select and you are ready to move to the next adjustment.

Adjustment Procedure

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere VarTech Systems Monitor Handbücher

VarTech Systems

VarTech Systems VT084XA4 Bedienungsanleitung

VarTech Systems

VarTech Systems VT520 Bedienungsanleitung

VarTech Systems

VarTech Systems VT181CH Bedienungsanleitung

VarTech Systems

VarTech Systems DiamondVue VT201C Bedienungsanleitung

VarTech Systems

VarTech Systems VT064C Bedienungsanleitung

VarTech Systems

VarTech Systems VTPC150XPE Bedienungsanleitung

VarTech Systems

VarTech Systems VT121 DiamondVue Series Bedienungsanleitung

VarTech Systems

VarTech Systems VT190PVS Bedienungsanleitung

VarTech Systems

VarTech Systems VT170W Bedienungsanleitung

VarTech Systems

VarTech Systems VT213C Bedienungsanleitung

VarTech Systems

VarTech Systems VT420 Series Bedienungsanleitung

VarTech Systems

VarTech Systems VT20A Bedienungsanleitung

VarTech Systems

VarTech Systems VT084XHB Bedienungsanleitung

VarTech Systems

VarTech Systems vt550 series Bedienungsanleitung

VarTech Systems

VarTech Systems DiamondVue VT150P Bedienungsanleitung

VarTech Systems

VarTech Systems ColorVue VT190PC Bedienungsanleitung

VarTech Systems

VarTech Systems VT14B-C1 Bedienungsanleitung

VarTech Systems

VarTech Systems GDM-5001PT Bedienungsanleitung

VarTech Systems

VarTech Systems VT29B-M Bedienungsanleitung

VarTech Systems

VarTech Systems VT14A-D Bedienungsanleitung

VarTech Systems

VarTech Systems VT121XA4 Bedienungsanleitung

VarTech Systems

VarTech Systems VT201CM Bedienungsanleitung

VarTech Systems

VarTech Systems VT121CC Bedienungsanleitung

VarTech Systems

VarTech Systems VT170CM Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung