Vaxcel T0572 Gebrauchsanweisung

191203

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

T0572

WARNING: Turn off the main power at circuit breaker before installing fixture.

AVERTISSEMENT: Coupez la source d’alimentation principale au panneau

central de disjoncteurs avant d’installer le luminaire.

Installation steps

1. Thread two headless screws (E) through the cross bar (A), and then secure them with four lock nuts (F) (two on each

side of the cross bar (A).) Adjust the length of the headless screws (E) if necessary.

Note: Make sure the headless screws are lined up horizontally to make the fixture level.

2. Attach the

cross bar

(A) to the outlet box by using two mounting screws (B).

Turn off the power at fuse or circuit box.

NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. READ AND SAVE THESE INSTRUCTIONS.

Hardware Package (included):

Green Grounding Screw (D)

Headless screw (E)

Mounting Screw (B) Wire Connector (C)

Lock Nut (F)

Bolt Nut (G) Rubber Pad (H)

Cross Bar (A)

Wire Connector (C)

House Grounding Wire

Outlet Box

Mounting Screw (B)

Green Grounding Screw (D)

Headless Screw (E)

Cross Bar (A)

Lock Nut (F)

Fixture Grounding Wire

Fixture Wire

Backplate

Photocell

Bolt Nut (G)

Rubber Pad (H)

Max.60W Type A Bulb

(not included)

Fixture

Socket

Shade

Socket Ring

191203

3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows:

• Connect the hot wire (usually black insulation) from the fixture to the black wire from the power source.

• Connect the neutral wire (usually white insulation) from the fixture to the white wire from the power source.

• Attach the fixture grounding wire (usually green insulation or bare wire) to the cross bar (A) with the green

grounding screw (D). Then, depending on local code connect it to the house grounding wire with the wire

connector (C).

Carefully put all of the wires back into the outlet box.

4. Attach the backplate of the fixture to the cross bar (A) by aligning and inserting the two headless screws (E) from

the cross bar (A) into the open holes on the backplate, then place the two rubber pads (H) over the exposed

headless screws (E) before screwing the two bolt nuts (G).

Note: With silicone caulking compound, caulk completely around where the backplate meets with the wall

surface to prevent water from seeping into the outlet box.

5. Attach shade to fixture, then secure it with socket ring.

6. Install bulb (not included). Check relamping label at socket area or packaging for maximum wattage allowed .

Turn on the power at fuse or circuit box.

1. Turn off the power at the fuse or circuit box before starting installation.

2. Loosen the wire connectors connected with the wires from photocell. (See Fig.1)

Note: Do not move the photocell to prevent water from seeping into the outlet box.

3. Take a white pigtail and black pigtail and make wire connections using wire connectors (C): (See Fig.2)

a. The black wire from the fixture to one end of the black pigtail.

b. The white wire from the fixture to one end of the white pigtail.

c. The other end of the black pigtail to the black wire from the power source.

d. The other end of the white pigtail to the white wire from the power source.

Put all wires back into the backplate of the fixture.

Operation the Unit Without Photocell

Fig.1 Fig.2

Photocell

White Wires From Photocell

Wire Connector

Wires From Fixture

Wires From

Main Power

Wire Connector (C)

White Pigtail

Pigtail

Red Wires From Photocell

Black Wires From Photocell

191203

Green Grounding Screw (D)

Headless screw (E)

Mounting Screw (B) Wire Connector (C)

Lock Nut (F)

Bolt Nut (G) Rubber Pad (H)

Cross Bar (A)

The following parts are available for re-order if damaged or missing.

Spare Parts List:

Mounting Hardware

6200MM (1SET)

A: 14”

B: 18”

C: 24-1/2”

Inhaltsverzeichnis

Andere Vaxcel Außenleuchte Handbücher

Vaxcel

Vaxcel T0112 Bedienungsanleitung

Vaxcel

Vaxcel T0568 Gebrauchsanweisung

Vaxcel

Vaxcel T0702 Gebrauchsanweisung

Vaxcel

Vaxcel T0620 Gebrauchsanweisung

Vaxcel

Vaxcel T0103 Gebrauchsanweisung

Vaxcel

Vaxcel T0451 Gebrauchsanweisung

Vaxcel

Vaxcel T0294 Gebrauchsanweisung

Vaxcel

Vaxcel T0575 Gebrauchsanweisung

Vaxcel

Vaxcel T0165 Gebrauchsanweisung

Vaxcel

Vaxcel T0363 Gebrauchsanweisung

Vaxcel

Vaxcel T0040 Gebrauchsanweisung

Vaxcel

Vaxcel T0199 Gebrauchsanweisung

Vaxcel

Vaxcel T0350 Gebrauchsanweisung

Vaxcel

Vaxcel T0395 Gebrauchsanweisung

Vaxcel

Vaxcel T0454 Gebrauchsanweisung

Vaxcel

Vaxcel Lambda T0627 Gebrauchsanweisung

Vaxcel

Vaxcel T0696 Gebrauchsanweisung

Vaxcel

Vaxcel T0085 Gebrauchsanweisung

Vaxcel

Vaxcel T0594 Gebrauchsanweisung

Vaxcel

Vaxcel T0366 Gebrauchsanweisung

Vaxcel

Vaxcel T0449 Gebrauchsanweisung

Vaxcel

Vaxcel T0599 Gebrauchsanweisung

Vaxcel

Vaxcel Chatham Gebrauchsanweisung

Vaxcel

Vaxcel T0238 Gebrauchsanweisung

Beliebte Außenleuchte Handbücher anderer Marken

Sealey

Sealey LED37 Bedienungsanleitung

nordlux

nordlux VEJERS Benutzerhandbuch

SImx

SImx ELITE LED LHTC637 Bedienungsanleitung

GEV

GEV CAROLINE 10833 Bedienungsanleitung

NEBO

NEBO NEB-LSP-0020 Bedienungsanleitung

WE-EF

WE-EF PFL540 LED Bedienungsanleitung

Lindby

Lindby 9949029 Bedienungsanleitung

HEPER

HEPER DOGO Side LW6048.585-US Montage- und Bedienungsanleitung

HEPER

HEPER LW8034.003-US Montage- und Bedienungsanleitung

Maretti

Maretti VIBE S 14.6080.04.A Bedienungsanleitung

BEGA

BEGA 84 253 Handbuch

HEPER

HEPER MINIMO Montage- und Bedienungsanleitung

LIGMAN

LIGMAN BAMBOO 3 Bedienungsanleitung

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Bedienungsanleitung

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Bedienungsanleitung

urban ambiance

urban ambiance UQL1273 Bedienungsanleitung

TotalPond

TotalPond 52238 Bedienungsanleitung

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Bedienungsanleitung